Square D Modbus Solution: Altivar 58 VFD

Size: px

Start display at page:

Download "Square D Modbus Solution: Altivar 58 VFD"

Valentine John Burke
5 years ago
Views:

1 Point Map November 1, 2004 Systems Integration Square D Modbus Solution: Altivar 58 VFD Table 1. Altivar 58 VFD Point Map, Application LAO Slave Address 1to247 2 LAI Application Number LDI Communication Fault Off/On 4 LAO First IP Address Byte 0 to LAO Second IP Address Byte 0to255 6 LAO Third IP Address Byte 0 to LAO Fourth IP Address Byte 0 to LAO IP Port LAO Base Offset 0to LAO Enable to Send Initial Values 0=No 1=Yes 11 LDO Drive Ready Command Notrdy/Ready 12 LDO Enable Output Voltage Command Disabl/Enable 13 LDO E-Stop Command Stop/Run 14 LDO Enable Command Disabl/Enable 18 LDO Fault Reset (Must Be Set Back to NORMAL by PPCL) Normal/Reset 22 LDO Motor Direction Command Fwd/Rev 23 LDO Motor Run/Stop with Ramp Command On/Off 24 LDO Stop by DC Injection Command Off/On 25 LDO Fast Stop Command Off/On 26 LDO Disable Serial Control Command Off/On 27 LAO Frequency Reference Command Hz 31 LDO External Fault Command Off/On 32 LDO Ramp Switching Command Off/On 41 LDO Drive Controller Locked at Stop Command 42 LDO Disable Timeout Enable/Disable 44 LAO PI Setpoint Command % 45 LAI Frequency Reference Hz Siemens Building Technologies, Inc. Page 1 of 6

2 46 LAI Output Frequency Applied to the Motor Hz 47 LAI Motor Speed Estimated by Controller rpm 48 LAI Motor Current A 49 LAI Line Voltage V 50 LAI Motor Thermal State % 51 LAI Drive Controller Thermal State % 52 LAI Last Fault SeeTable2 53 LDI Power Ready for Startup Notrdy/Ready 54 LDI Drive Controller Ready Notrdy/Ready 55 LDI DRIVECOM Stop/Run 56 LDI Fault Present Off/On 57 LDI Power Present On/Off 58 LDI E-Stop in Progress On/Off 59 LDI Status - Switching Enabled On/Off 60 LDI Alarm Present Normal/Alarm 62 LDI Forced Local Active Off/On 63 LDI Speed Reference Reached Off/On 64 LDI LFRD Reference Exceeded Off/On 67 LDI STOP from Keyboard Off/On 68 LDI Direction of Rotation Fwd/Rev 73 LDI Motor Running Off/On 74 LDI DC Injection Off/On 75 LDI Drive Controller Running in Steady Mode Off/On 76 LDI Thermal Overload Alarm Off/On 77 LDI Ecess Breaking Alarm Off/On 78 LDI Drive Controller Accelerating Off/On 79 LDI Drive Controller Decelerating Off/On 80 LDI Current Limit Alarm Off/On 84 LDI Forward/Reverse Request Off/On 88 LDI High Speed Reached Off/On 89 LDI Speed Reference Reached Off/On 90 LDI Frequency Threshold Reached Off/On 91 LDI Current Threshold Reached Off/On 92 LDI PID Feedback Fault Off/On 93 LDI PID Error Exceeded Off/On Page 2 of 6 Siemens Building Technologies, Inc.

3 117 LAI Past Fault No. 1 SeeTable2 118 LAI Status During Past Fault 1 See Table LAI Past Fault No. 2 SeeTable2 120 LAI Status During Past Fault 2 See Table LAI Past Fault No. 3 SeeTable2 122 LAI Status During Past Fault 3 See Table LAI Past Fault No. 4 SeeTable2 124 LAI Status During Past Fault 4 See Table LAI Past Fault No. 5 SeeTable2 126 LAI Status During Past Fault 5 See Table LAI Past Fault No. 6 SeeTable2 128 LAI Status During Past Fault 6 See Table LAI Past Fault No. 7 SeeTable2 130 LAI Status During Past Fault 7 See Table LAI Past Fault No. 8 SeeTable2 132 LAI Status During Past Fault 8 See Table LDI State of Logic Input 1 Off/On 134 LDI State of Logic Input 2 Off/On 135 LDI State of Logic Input 3 Off/On 136 LDI State of Logic Input 4 Off/On 137 LDI State of Logic Input 5 Off/On 138 LDI State of Logic Input 6 Off/On 141 LDO State of Relay1 Command Relay2 if Enabled Off/On 142 LDO State of Relay2 Command Relay2 if Enabled Off/On 143 LDO State of Logic Output Command of Logic Output if Enabled Off/On 144 LDI State of Red Fault LED Off/On 145 LDI State of Precharge Relay Off/On 146 LDI State of Dynamic Break Transistor Off/On 149 LAI State of Analog input AI1 V 150 LAI State of Analog input AI2 ma 151 LAI State of Analog input AI3 V 152 LAO Image of Analog Output Command Analog Output if Enabled ma 153 LDI Incorrect Calibration Constants Normal/Fail 154 LDI Unknown Drive Controller Rating Normal/Fail 155 LDI Unknown or Incompatible Option Normal/Fail Siemens Building Technologies, Inc. Page 3 of 6

4 156 LDI HD (ASIC) Initialization Incorrect Normal/Fail 157 LDI EEPROM Control Board Fault Normal/Fail 158 LDI EPROM Power Board Fault Normal/Fail 159 LDI Incorrect Configuration Normal/Fail 160 LDI Invalid Configuration Normal/Fail 161 LDI Standard Communication Link Fault Normal/Fail 162 LDI Fast Communication Link Fault Normal/Fail 163 LDI Fast Communication Network Fault Normal/Fail 164 LDI External Fault via Standard Serial Link Normal/Fail 165 LDI External Fault via Fast Serial Link Normal/Fail 166 LDI Motor Short Circuit Fault Normal/Fail 167 LDI Precharge Relay Closure Too Long Normal/Fail 168 LDI Precharge Relay Command Cut-off Normal/Fail 169 LDI Speed Feedback Loss Normal/Fail 170 LDI Overspeed with Speed Feedback Normal/Fail 171 LDI Ramp Not Followed with Speed Feedback Normal/Fail 172 LDI Overcurrent Fault Normal/Fail 173 LDI Loss of Follower Fault Normal/Fail 174 LDI Thermal Sensor Fault Normal/Fail 175 LDI Motor Overheating Fault Normal/Fail 176 LDI Drive Controller Overheating Fault Normal/Fail 177 LDI Motor Overload Fault Normal/Fail 178 LDI Fast Communication Time-out Fault Normal/Fail 179 LDI DC Bus Overvoltage Fault Normal/Fail 180 LDI Input Supply Overvoltage Fault Normal/Fail 181 LDI Motor Phase Loss Fault Normal/Fail 182 LDI Input Supply Phase Loss Fault Normal/Fail 183 LDI Input Supply Undervoltage Fault Normal/Fail 184 LDI Control Board Power Supply Fault Normal/Fail 185 LAI Number of Motor Pole Pairs 187 LAI Motor Torque % 188 LAI Ramp Output Hz 191 LAI Output Power Estimated by the Drive Controller % 192 LAO Analog Output AO1 Value (Only FVC Models) ma Page 4 of 6 Siemens Building Technologies, Inc.

5 193 LAI Voltage Applied to Motor (Only FVC Models) V 194 LAI Drive Power Meter 1 to MWh 195 LAI Total Motor Run Time hrs a Values noted for LDIs and LDOs are in the following format: OFF text/on text. b This column indicates the value/range or engineering units or both if known. c The default English value is not italicized. An italicized entry indicates an SI value. Table 2. Fault Values (Points 52, 117, 119, 121, 123, 125, 129, and 131). Value Description 0 No Fault 1 Internal Fault 2 EEPROM Memory Fault 3 Configuration Parameter Incorrect 4 Configuration Parameter Invalid 5 Standard Communication Link Fault 6 Fast Communication Link Fault 7 Fast Communication Network Fault 8 External Fault 9 Overcurrent Fault 10 Precharge Relay Fault 11 Loss of Speed FB Fault 12 Ramp Not Followed Fault 13 Loss of Follower Fault 14 Thermal Sensor Fault 15 Motor Overheating Fault 16 Drive Controller Overheating Fault 17 Motor Overload Fault 18 DC Bus Overvoltage Fault 19 Input Supply Overvoltage Fault 20 Motor Phase Loss Fault 21 Input Supply Phase Loss Siemens Building Technologies, Inc. Page 5 of 6

6 Table 2. Fault Values (Points 52, 117, 119, 121, 123, 125, 129, and 131). (continued) Value Description 22 Input Supply Undervoltage Fault 23 Motor Short Circuit Fault 24 Overspeed Fault Table 3. Fault Status Values (Points 118, 120, 122, 124, 126, 128, 130, and 132). Value Description Bit 0 Controller Ready Bit 1 E-Stop Not in Progress Bit 2 Switching Disabled Bit 3 Forced Local Inactive Bit 4 Reverse Rotation Bit 5 Motor Running Bit 6 DC Injection Bit 7 Thermal Overload Alarm Bit 8 Excessive Breaking Alarm Bit 9 Drive Accelerating Bit 10 Drive Decelerating Bit 11 Current Limit Alarm Bit 12 Reserved Bit 13 Control via Keypad Bit 14 Control via Fast Serial Link Bit 15 Reverse Requested Information in this document is based on specifications believed correct at the time of publication. The right is reserved to make changes as design improvements are introduced. Product or company names mentioned herein may be the trademarks of their respective owners Siemens Building Technologies, Inc. Siemens Building Technologies, Inc Deerfield Parkway Country of Origin: US Buffalo Grove, IL Page 6 of 6 U.S.A.

LONWORKS Solution to Danfoss Graham VLT 6000 Adjustable Frequency Drive

Point Map February 23, 2007 Systems Integration LONWORKS Solution to Danfoss Graham VLT 6000 Adjustable Frequency Drive Table 1. VLT 6000 APOGEE Points, Application Number:9098, Program ID:80:00:08:3C:0A:04:04:04.