Cable Schedule - Electronic Engine Controls Ref. Dwg. No. 6525A-0005 rev. 0

Transcription

1 Cable Schedule - Electronic Engine Controls Ref. Dwg. No. 6525A-0005 rev. 0 Alternative after 2004 Acceptable to use by H. A. 9 Sept. 03 (PO42589 Oct 2004) Kobelt P/N Cable Use Spec. Manufacturer Part No. Approval 6525A-P10 Power 2 cond. 12 AWG Bostrig DPN-12 DNV, ABS, LR 6525A-C10 Comm./ Power 2 pair 18 AWG shielded Bostrig TP(I/S-O/S)18PN-2 DNV, ABS, LR 6525A-A10 Actuator 4 pair 18 AWG shielded Bostrig TP(I/S-O/S)18PN-4 DNV, ABS, LR 6525A-S10 Synchro 7 cond. 18 AWG Bostrig C16PN-7 DNV, ABS, LR 6525A-B10 Brake / Neutral 7 cond. 18 AWG Bostrig C16PN-7 DNV, ABS, LR 6525A-CT10 PWM / 4-20 ma 2 cond. 18 AWG Bostrig TP(OS)18PN-1 DNV, ABS, LR 6525A-CT10 Electric Clutch 3 cond. 18 AWG Bostrig TT(OS)18PN-1 DNV, ABS, LR Cable Satellite 7 cond. 22 AWG expires Cable Satellite 15 cond. 22 AWG (ABS) 03-HS347018A/2-PDA 5/22/2013 Wire Hookup 22 AWG (DNV) E-8792, E-8793, E /31/2011 Wire Hookup 16 AWG (LRS) 95/60161, 95/ /29/2010 Kobelt P/N Cable Use Spec. Manufacturer Part No. Approval 6525A-P10 Power 2 cond. 12 AWG Amercable DNV, ABS, LRS 6525A-C10 Comm./ Power 2 pair 18 AWG shielded Amercable DNV, ABS, LRS 6525A-A10 Actuator 4 pair 18 AWG shielded Amercable DNV, ABS, LRS 6525A-S10 Synchro 7 cond. 18 AWG Amercable DNV, ABS, LRS 6525A-B10 Brake / Neutral 7 cond. 18 AWG Amercable DNV, ABS, LRS 6525A-CT10 PWM / 4-20 ma 2 cond. 18 AWG Amercable DNV, ABS, LRS 6525A-CT10 Electric Clutch 3 cond. 18 AWG Amercable DNV, ABS, LRS Cable Satellite 7 cond. 22 AWG expires Cable Satellite 15 cond. 22 AWG (ABS) 03-HS290310/2 7/30/2013 Wire Hookup 22 AWG (DNV) E5001, E5002 6/30/2003 Wire Hookup 16 AWG (LRS) 91/60333 (E6) 5/10/2009 Cable sources.xls Approved Cables 2009

2

3

4

5

6

7 Certificate Number: 03-HS347018A/4-PDA Confirmation of Product Type Approval 05/MAY/2009 Please refer to the "Service Restrictions" shown below to determine if Unit Certification is required for this product. This is to certify that, pursuant to the Rules of the American Bureau of Shipping (ABS), the manufacturer of the below listed product held a valid Manufacturing Assessment (MA) with expiration date of 16/APR/2014. The continued validity of the Manufacturing Assessment is dependent on completion of satisfactory audits as required by the ABS Rules. And; a Product Design Assessment (PDA) valid until 22/MAY/2013 subject to continued compliance with the Rules or standards used in the evaluation of the product. The above entitle the product to be called Product Type Approved. The Product Design Assessment is valid for products intended for use on ABS classed vessels, MODUs or facilities which are in existence or under contract for construction on the date of the ABS Rules used to evaluate the Product. ABS makes no representations regarding Type Approval of the Product for use on vessels, MODUs or facilities built after the date of the ABS Rules used for this evaluation. Due to wide variety of specifications used in the products ABS has evaluated for Type Approval, it is part of our contract that; whether the standard is an ABS Rule or a non-abs Rule, the Client has full responsibility for continued compliance with the standard. DRAKA CABLETEQ USA Model Name(s): Bostrig 125 Type "P", Multiconductor, 2-91 conductors sizes 18 AWG through 10 AWG Presented to: DRAKA CABLETEQ USA 22 JOSEPH EDWARNER BLVD NORTH DIGHTON MA United States Intended Service: Description: Ratings: Service Restrictions: Comments: Notes / Documentation: General power, lighting, control, and instrumentation Multiconductor, 2-91 conductors sizes 18 AWG through 10 AWG; Unshielded & shielded (Individual and/or overall shield) Instrumentation Cable; Marine shipboard cables employing crosslined polyolefin insulation and polychloroprene jackets with optional aluminum or bronze braided armor and optional overall polychloroprene sheath For IEEE - Voltage Class: 0.6 KV/2K; Insulation: Crosslinked Polyolefin - Type "P"; Temperature Class: 100 degrees C; Flame Tests: IEEE-1580 (2001); For IEC : Voltage Class: 0.6 KV/1KV; Insulation: Class X95; Temperature Class: 95 degrees C; Flame Tests: IEC Category "A, A/F" Unit Certification is not required for this product. If the manufacturer or purchaser request an ABS Certificate for compliance with a specification or standard, the specification or standard, including inspection standards and tolerances, must be clearly defined. Duplicated PDAs have been issued to Draka Cableteq USA, 1 Tamaqua Blvd. Schuylkill Haven, PA 17972; Draka Industrial Cable GMBH, Dickestresse 23, Wuppertal, Germany; and Suzhou Draka Cable Co., Ltd, Suzhou, Jaingsu Province , China. This Product Design Assessment (PDA) is valid only for products intended for use on ABS classed vessels, MODUs or facilities which are in existence or under contract for construction on the date of the ABS Rules used to evaluate the 05/05/ :04:03 AM Copyright 2001 American Bureau of Shipping. All rights reserved. Page 1 of 2

8 Certificate Number: 03-HS347018A/4-PDA Term of Validity: Product. This Design Assessment Certificate number 03-HS347018A/4-PDA, dated 23/May/2008 will expire on 22/May/2013 or at an earlier date should there be alterations to the product's design or changes to the referenced ABS Rules and other specifications, which affect the product. Product use on or after 1 January 2009, will be subject to compliance with the ABS Rules or specifications in effect when the vessel, MODU or facility is contracted. The product's acceptability on board ABS-classed vessels or facilities is defined in the service restrictions of this certificate. ABS Rules: 2008 Steel Vessel Rules 1-1-4/7.7; 4-8-3/ MODU Rules 4-3-4/13.1. National Standards: Intertek Testing Service Report No Revised date 26 Dec 2002 (UL 1309, July 14, 1995; CSA C22.2 No. 245, July 14, 1995; IEEE Std , June 14, 2001) International Standards: Performance tested IEC , IEC Government Authority: EUMED: Others: BIW Specifying Standards J-104, J105, J-106 ABS Programs ABS has used due diligence in the preparation of this certificate and it represents the information on the product in the ABS Records as of the date and time the certificate was printed. Type Approval requires Drawing Assessment, Prototype Testing and assessment of the manufacturer's quality assurance and quality control arrangements. Limited circumstances may allow only Prototype Testing to satisfy Type Approval. The approvals of Drawings and Products remain valid as long as the ABS Rule, to which they were assessed, remains valid. ABS cautions manufacturers to review and maintain compliance with all other specifications to which the product may have been assessed. Further, unless it is specifically indicated in the description of the product; Type Approval does not necessarily waive witnessed inspection or survey procedures (where otherwise required) for products to be used in a vessel, MODU or facility intended to be ABS classed or that is presently in class with ABS. Questions regarding the validity of ABS Rules or the need for supplemental testing or inspection of such products should, in all cases, be addressed to ABS. 05/05/ :04:03 AM Copyright 2001 American Bureau of Shipping. All rights reserved. Page 2 of 2

9 pnfdaxxx Page 1 of 4 DET NORSKE VERITAS TYPE APPROVAL CERTIFICATE CERTIFICATE NO. E-8794 This Certificate consists of 3 pages This is to certify that the Electric Cable, Power Current with type designation(s) BOSTRIG-125 Type P, SP, BOSTRIG-125 Type P, SP2KV Holder of certificate Draka Marine, Oil & Gas International Houston, TX 77032, United States is found to comply with Det Norske Veritas' Rules for Classification of Ships, High Speed & Light Craft and Det Norske Veritas' Offshore Standards IEEE IEEE IEC ( ) Application Switch board Wires Type Voltage class (kv) Temp. class ( C) BOSTRIG-125 Type P, SP 0,6/1 95

10 pnfdaxxx Page 2 of 4 BOSTRIG-125 Type P, SP2KV 2 95 Place and date This Certificate is valid until Høvik, for Det Norske Veritas AS Name and place of manufacturer: Product description Marit Laumann Local Office Ivar Bull Head of Section DNV New York Surveyor Draka Cableteq USA North Dighton MA USA Construction: Conductor: Tinned stranded copper Insulation: XLPO (Type P) Number of cores x conductor cross-section Overall diameter Type designation mm 2 AWG/MCM mm Inches 1 x 18 2,92 0,115 SP-18 1 x 16 3,05 0,120 SP-16 1 x 14 3,43 0,135 SP-14 1 x 3, ,81 0,150 SP-12 1 x 5, ,70 0,185 SP-10 1 x 7,57 8 5,97 0,235 SP-8 1 x 12,5 6 7,49 0,295 SP-6 1 x 18,6 5 8,51 0,335 SP-5 1 x 21,5 4 9,02 0,355 SP-4 1 x 25,6 3 9,65 0,380 SP-3 1 x 30,7 2 10,41 0,410 SP-2 1 x 46,0 1 12,57 0,495 SP-1 1 x 56,3 1/0 13,97 0,550 SP-1/0 1 x 66,5 2/0 14,35 0,565 SP-2/0 1 x 92,1 3/0 17,02 0,670 SP-3/0 1 x 18 3,68 0,145 SP2KV-18 1 x 16 3,81 0,150 SP2KV-16 1 x 14 4,19 0,165 SP2KV-14 1 x 3, ,57 0,180 SP2KV-12

11 pnfdaxxx Page 3 of 4 1 x 5, ,46 0,215 SP2KV-10 1 x 7,57 8 6,48 0,255 SP2KV-8 1 x 12,5 6 8,00 0,315 SP2KV-6 1 x 18,6 5 9,02 0,355 SP2KV-5 1 x 21,5 4 9,53 0,375 SP2KV-4 1 x 25,6 3 10,16 0,400 SP2KV-3 1 x 30,7 2 10,92 0,430 SP2KV-2 1 x 46,0 1 13,08 0,515 SP2KV-1 1 x 56,3 1/0 14,48 0,570 SP2KV-1/0 1 x 66,5 2/0 14,86 0,585 SP2KV-2/0 1 x 92,1 3/0 17,53 0,690 SP2KV-3/0 Application/Limitation The cable may be installed and sized according to IEC , except for the 1 conditions listed below. 1. Cable ends with flexible rope stranded conductors are to be terminated using approved pressurised terminals suitable for these conductors. The requirements of SOLAS Amendments 1981 Chapter II-1, Part D, Reg. 45, 5.2 (provision to be taken to limit Fire Propagation along Bunches of Cables or Wires) are fulfilled without any additional measures. Type Approval documentation Tests carried out Test according to IEEE 45 (1993) Draft, IEEE 45 (1998), IEEE 1580 (2001) and IEC cat. A. Marking of product Draka 32 BOSTRIG-125 Type P - Type designation - Size of conductors - Voltage. Certificate retention survey The scope of the retention/renewal survey is to verify that the conditions stipulated for the Type approval is complied with and that no alterations are made to the product design or choice of materials. The main elements of the survey are: Inspection on factory samples, selected at random from the production line (where practicable) Results from Production Sample Tests (PST) and Routines (RT) checked (if not available tests according to PST and RT to be carried out) Review of type approval documentation

12 pnfdaxxx Page 4 of 4 Review of possible change in design, materials and performance Ensuring traceability between manufacturer's product type marking and Type Approval Certificate. Survey to be performed at least every second year. END OF CERTIFICATE Notice: This Certificate is subject to terms and conditions overleaf. Any significant change in design or construction may render this Certificate invalid. If any person suffers loss or damage which is proved to have been caused by any negligent act or omission of Det Norske Veritas, then Det Norske Veritas shall pay compensation to such person for his proved direct loss or damage. However, the compensation shall not exceed an amount equal to ten times the fee charged for the service in question, provided that the maximum compensation shall never exceed USD 2 million.in this provision "Det Norske Veritas" shall mean the Foundation Det Norske Veritas as well as all its subsidiaries, directors, officers, employees, agents and any other acting on behalf of Det Norske Veritas. DET NORSKE VERITAS AS VERITASVEIEN 1, 1322 HØVIK, NORWAY TEL: (+47) FAX: (+47)

13 gnfdaxxx Page 1 of 13 DET NORSKE VERITAS TYPE APPROVAL CERTIFICATE CERTIFICATE NO. E-8793 This Certificate consists of 6 pages This is to certify that the Electric Cable, Power Current with type designation(s) BOSTRIG-125 Type P,...PN- Holder of certificate Draka Marine, Oil & Gas International Houston, TX 77032, United States is found to comply with Det Norske Veritas' Rules for Classification of Ships, High Speed & Light Craft and Det Norske Veritas' Offshore Standards IEEE IEEE IEC ( ) Application Instrumentation and communication Voltage class (kv) 0,6/1 Temp. class ( C) 95

14 gnfdaxxx Page 2 of 13 Place and date This Certificate is valid until Høvik, for Det Norske Veritas AS Name and place of manufacturer: Product description Marit Laumann Local Office Ivar Bull Head of Section DNV New York Surveyor Draka Cableteq USA North Dighton MA USA Construction: Conductor: Tinned stranded copper Insulation: XLPO (Type P) Shield: Individual shield (I/S) and/or overall shield (OS) Aluminium mylar with a drain wire Tinned copper wire braid Filler: Flame Retardant, non hygroscopic (as needed) Outer sheath: SP1 (Type N) Number of cores x conductor Overall diameter Type designation cross-section mm 2 AWG mm Inches 1 x 2 x 20 8,38 0,330 TP(OS)20PN-1 2 x 2 x 20 12,57 0,495 TP(I/S)20PN-2 3 x 2 x 20 13,21 0,520 TP(I/S)20PN-3 4 x 2 x 20 14,61 0,575 TP(I/S)20PN-4 5 x 2 x 20 16,38 0,645 TP(I/S)20PN-5 6 x 2 x 20 17,65 0,695 TP(I/S)20PN-6 7 x 2 x 20 17,65 0,695 TP(I/S)20PN-7 8 x 2 x 20 19,18 0,755 TP(I/S)20PN-8 10 x 2 x 20 22,73 0,895 TP(I/S)20PN x 2 x 20 23,37 0,920 TP(I/S)20PN-12

15 gnfdaxxx Page 3 of x 2 x 19 x 2 x 20 x 2 x 24 x 2 x 25 x 2 x 20 26,04 1,025 TP(I/S)20PN ,56 1,085 TP(I/S)20PN ,58 1,125 TP(I/S)20PN ,00 1,260 TP(I/S)20PN ,02 1,300 TP(I/S)20PN-25 1 x 2 x 18 8,89 0,350 TP(OS)18PN-1 2 x 2 x 18 13,97 0,550 TP(I/S)18PN-2 3 x 2 x 18 14,22 0,560 TP(I/S)18PN-3 4 x 2 x 18 15,49 0 TP(I/S)18PN-4 5 x 2 x 18 17,27 0,680 TP(I/S)18PN-5 6 x 2 x 18 18,80 0,740 TP(I/S)18PN-6 7 x 2 x 18 18,80 0,740 TP(I/S)18PN-7 8 x 2 x 18 23,11 0,910 TP(I/S)18PN-8 10 x 2 x 18 24,89 0,980 TP(I/S)18PN x 2 x 18 25,65 1,010 TP(I/S)18PN x 2 x 18 27,05 1,065 TP(I/S)18PN x 2 x 18 29,34 1,155 TP(I/S)18PN x 2 x 18 31,37 5 TP(I/S)18PN x 2 x 18 36,20 1,425 TP(I/S)18PN-24 1 x 2 x 16 8,89 0,350 TP(OS)16PN-1 2 x 2 x 16 14,22 0,560 TP(I/S)16PN-2 3 x 2 x 16 15,49 0 TP(I/S)16PN-3 4 x 2 x 16 16,89 0,665 TP(I/S)16PN-4 5 x 2 x 16 18,54 0,730 TP(I/S)16PN-5 6 x 2 x 16 20,32 0,800 TP(I/S)16PN-6 7 x 2 x 16 20,32 0,800 TP(I/S)16PN-7 8 x 2 x 16 23,88 0,940 TP(I/S)16PN-8 10 x 2 x 16 25,53 1,005 TP(I/S)16PN x 2 x 16 26,92 1,060 TP(I/S)16PN x 2 x 16 29,46 1,160 TP(I/S)16PN-15

16 gnfdaxxx Page 4 of x 2 x 20 x 2 x 22 x 2 x 24 x 2 x 16 29,97 1,180 TP(I/S)16PN ,02 1,300 TP(I/S)16PN ,31 1,390 TP(I/S)16PN ,48 1,515 TP(I/S)16PN-24 1 x 2 x 14 10,03 0,395 TP(OS)14PN-1 2 x 2 x 14 15,88 0,625 TP(I/S)14PN-2 3 x 2 x 14 17,15 0,675 TP(I/S)14PN-3 4 x 2 x 14 18,54 0,730 TP(I/S)14PN-4 5 x 2 x 14 20,45 0,805 TP(I/S)14PN-5 6 x 2 x 14 23,24 0,915 TP(I/S)14PN-6 7 x 2 x 14 23,24 0,915 TP(I/S)14PN-7 8 x 2 x 14 25,15 0,990 TP(I/S)14PN-8 10 x 2 x 14 27,05 1,065 TP(I/S)14PN x 2 x 14 29,46 1,160 TP(I/S)14PN x 2 x 14 32,89 1,295 TP(I/S)14PN x 2 x 14 37,72 1,485 TP(I/S)14PN x 2 x 14 42,29 1,665 TP(I/S)14PN-24 1 x 3 x 18 9,14 0,360 TT(OS)18PN-1 2 x 3 x 18 15,24 0,600 TT(I/S)18PN-2 3 x 3 x 18 16,13 0,635 TT(I/S)18PN-3 4 x 3 x 18 17,78 0,700 TT(I/S)18PN-4 5 x 3 x 18 19,56 0,770 TT(I/S)18PN-5 6 x 3 x 18 22,23 0,875 TT(I/S)18PN-6 7 x 3 x 18 22,23 0,875 TT(I/S)18PN-7 8 x 3 x 18 24,13 0,950 TT(I/S)18PN-8 12 x 3 x 18 29,21 1,150 TT(I/S)18PN x 3 x 18 32,64 1,285 TT(I/S)18PN-16 1 x 3 x 16 9,40 0,370 TT(OS)16PN-1 2 x 3 x 16 15,88 0,625 TT(I/S)16PN-2 3 x 3 x 16 16,89 0,665 TT(I/S)16PN-3 4 x 3 x 16 18,67 0,735 TT(I/S)16PN-4 5 x 3 x 16 20,57 0,810 TT(I/S)16PN-5

17 gnfdaxxx Page 5 of 13 6 x 3 x 16 22,99 0,905 TT(I/S)16PN-6 8 x 3 x 16 26,92 1,060 TT(I/S)16PN-8 12 x 3 x 16 30,73 1,210 TT(I/S)16PN x 3 x 16 34,42 1,355 TT(I/S)16PN-16 2 x 2 x 20 13,72 0,540 TP(I/S-OS)20PN-2 3 x 2 x 20 13,97 0,550 TP(I/S-OS)20PN-3 4 x 2 x 20 15,24 0,600 TP(I/S-OS)20PN-4 5 x 2 x 20 16,51 0,650 TP(I/S-OS)20PN-5 6 x 2 x 20 17,78 0,700 TP(I/S-OS)20PN-6 7 x 2 x 20 17,78 0,700 TP(I/S-OS)20PN-7 8 x 2 x 20 19,30 0,760 TP(I/S-OS)20PN-8 10 x 2 x 12 x 2 x 16 x 2 x 20 x 2 x 24 x 2 x 20 22,86 0,900 TP(I/S-OS)20PN ,50 0,925 TP(I/S-OS)20PN ,16 1,030 TP(I/S-OS)20PN ,70 1,130 TP(I/S-OS)20PN ,13 1,265 TP(I/S-OS)20PN x 2 x 18 15,37 0,605 TP(I/S-OS)18PN-2 3 x 2 x 18 16,13 0,635 TP(I/S-OS)18PN-3 4 x 2 x 18 17,15 0,675 TP(I/S-OS)18PN-4 5 x 2 x 18 18,03 0,710 TP(I/S-OS)18PN-5 6 x 2 x 18 19,43 0,765 TP(I/S-OS)18PN-6 7 x 2 x 18 20,32 0,800 TP(I/S-OS)18PN-7 8 x 2 x 18 24,38 0 TP(I/S-OS)18PN-8 10 x 2 x 12 x 2 x 14 x 2 x 16 x 2 x 20 x 2 x 24 x 2 x 18 26,04 1,025 TP(I/S-OS)18PN ,54 1,045 TP(I/S-OS)18PN ,94 1,100 TP(I/S-OS)18PN ,46 1,160 TP(I/S-OS)18PN ,50 1,240 TP(I/S-OS)18PN ,83 1,450 TP(I/S-OS)18PN x 2 x 16 15,75 0,620 TP(I/S-OS)16PN-2 3 x 2 x 16 16,89 0,665 TP(I/S-OS)16PN-3

18 gnfdaxxx Page 6 of 13 4 x 2 x 16 17,65 0,695 TP(I/S-OS)16PN-4 5 x 2 x 16 18,80 0,740 TP(I/S-OS)16PN-5 6 x 2 x 16 20,45 0,805 TP(I/S-OS)16PN-6 7 x 2 x 16 20,45 0,805 TP(I/S-OS)16PN-7 8 x 2 x 16 25,02 0,985 TP(I/S-OS)16PN-8 10 x 2 x 12 x 2 x 16 x 2 x 20 x 2 x 24 x 2 x 16 25,65 1,010 TP(I/S-OS)16PN ,05 1,065 TP(I/S-OS)16PN ,10 1,185 TP(I/S-OS)16PN ,15 1,305 TP(I/S-OS)16PN ,61 1,520 TP(I/S-OS)16PN x 2 x 14 16,26 0,640 TP(I/S-OS)14PN-2 3 x 2 x 14 17,27 0,680 TP(I/S-OS)14PN-3 4 x 2 x 14 19,05 0,750 TP(I/S-OS)14PN-4 5 x 2 x 14 20,57 0,810 TP(I/S-OS)14PN-5 6 x 2 x 14 23,37 0,920 TP(I/S-OS)14PN-6 7 x 2 x 14 23,37 0,920 TP(I/S-OS)14PN-7 8 x 2 x 14 25,27 0,995 TP(I/S-OS)14PN-8 10 x 2 x 12 x 2 x 16 x 2 x 20 x 2 x 24 x 2 x 14 27,18 1,070 TP(I/S-OS)14PN ,59 1,165 TP(I/S-OS)14PN ,02 1,300 TP(I/S-OS)14PN ,85 1,490 TP(I/S-OS)14PN ,42 1,670 TP(I/S-OS)14PN x 2 x 1, ,37 1,550 TP(I/S-OBS) 18PN-14 2 x 3 x 18 15,37 0,605 TT(I/S-OS)18PN-2 3 x 3 x 18 16,26 0,640 TT(I/S-OS)18PN-3 4 x 3 x 18 17,91 0,705 TT(I/S-OS)18PN-4 5 x 3 x 18 19,69 0,775 TT(I/S-OS)18PN-5 6 x 3 x 18 22,35 0,880 TT(I/S-OS)18PN-6 7 x 3 x 18 22,35 0,880 TT(I/S-OS)18PN-7 8 x 3 x 18 24,26 0,955 TT(I/S-OS)18PN-8 12 x 3 x 18 29,34 1,155 TT(I/S-OS)18PN- 12

19 gnfdaxxx Page 7 of x 3 x 18 32,77 1,290 TT(I/S-OS)18PN x 3 x 16 16,00 0,630 TT(I/S-OS)16PN-2 3 x 3 x 16 17,02 0,670 TT(I/S-OS)16PN-3 4 x 3 x 16 18,80 0,740 TT(I/S-OS)16PN-4 5 x 3 x 16 20,70 0,815 TT(I/S-OS)16PN-5 6 x 3 x 16 23,11 0,910 TT(I/S-OS)16PN-6 8 x 3 x 16 25,65 1,010 TT(I/S-OS)16PN-8 12 x 3 x 16 x 3 x 16 30,86 1,215 TT(I/S-OS)16PN ,54 1,360 TT(I/S-OS)16PN x 2 x 20 12,45 0,490 TP(OS)20PN-2 3 x 2 x 20 12,70 0,500 TP(OS)20PN-3 4 x 2 x 20 13,59 0,535 TP(OS)20PN-4 5 x 2 x 20 15,62 5 TP(OS)20PN-5 6 x 2 x 20 16,13 0,635 TP(OS)20PN-6 7 x 2 x 20 16,13 0,635 TP(OS)20PN-7 8 x 2 x 20 17,78 0,700 TP(OS)20PN-8 10 x 2 x 20 20,07 0,790 TP(OS)20PN x 2 x 20 20,83 0,820 TP(OS)20PN x 2 x 20 24,38 0 TP(OS)20PN x 2 x 20 25,40 1,000 TP(OS)20PN x 2 x 20 28,70 1,130 TP(OS)20PN-24 2 x 2 x 18 13,46 0,530 TP(OS)18PN-2 3 x 2 x 18 14,22 0,560 TP(OS)18PN-3 4 x 2 x 18 15,49 0 TP(OS)18PN-4 5 x 2 x 18 17,27 0,680 TP(OS)18PN-5 6 x 2 x 18 17,91 0,705 TP(OS)18PN-6 7 x 2 x 18 17,91 0,705 TP(OS)18PN-7 8 x 2 x 18 19,56 0,770 TP(OS)18PN-8 10 x 2 x 18 23,11 0,910 TP(OS)18PN x 2 x 18 24,00 0,945 TP(OS)18PN x 2 x 18 25,15 0,990 TP(OS)18PN x 2 x 18 26,92 1,060 TP(OS)18PN-16

20 gnfdaxxx Page 8 of x 2 x 24 x 2 x 18 28,07 1,105 TP(OS)18PN ,00 1,260 TP(OS)18PN-24 2 x 2 x 16 13,84 0,545 TP(OS)16PN-2 3 x 2 x 16 14,61 0,575 TP(OS)16PN-3 4 x 2 x 16 15,88 0,625 TP(OS)16PN-4 5 x 2 x 16 17,02 0,670 TP(OS)16PN-5 6 x 2 x 16 18,29 0,720 TP(OS)16PN-6 7 x 2 x 16 18,29 0,720 TP(OS)16PN-7 8 x 2 x 16 23,62 0,930 TP(OS)16PN-8 10 x 2 x 16 23,88 0,940 TP(OS)16PN x 2 x 16 24,77 0,975 TP(OS)16PN x 2 x 16 27,69 1,090 TP(OS)16PN x 2 x 16 28,96 1,140 TP(OS)16PN x 2 x 16 32,77 1,290 TP(OS)16PN-24 2 x 2 x 14 15,24 0,600 TP(OS)14PN-2 3 x 2 x 14 16,00 0,630 TP(OS)14PN-3 4 x 2 x 14 17,53 0,690 TP(OS)14PN-4 5 x 2 x 14 19,56 0,770 TP(OS)14PN-5 6 x 2 x 14 20,32 0,800 TP(OS)14PN-6 7 x 2 x 14 20,32 0,800 TP(OS)14PN-7 8 x 2 x 14 23,37 0,920 TP(OS)14PN-8 10 x 2 x 14 26,42 1,040 TP(OS)14PN x 2 x 14 27,43 1,080 TP(OS)14PN x 2 x 14 30,73 1,210 TP(OS)14PN x 2 x 14 32,26 1,270 TP(OS)14PN x 2 x 14 38,10 1,500 TP(OS)14PN-24 2 x 2 x 20 13,21 0,520 TP(OBS)20PN-2 3 x 2 x 20 13,59 0,535 TP(OBS)20PN-3 4 x 2 x 20 14,99 0,590 TP(OBS)20PN-4 5 x 2 x 20 16,38 0,645 TP(OBS)20PN-5

21 gnfdaxxx Page 9 of 13 6 x 2 x 20 16,89 0,665 TP(OBS)20PN-6 7 x 2 x 20 16,89 0,665 TP(OBS)20PN-7 8 x 2 x 20 18,67 0,735 TP(OBS)20PN-8 10 x 2 x 20 20,83 0,820 TP(OBS)20PN x 2 x 20 22,61 0,890 TP(OBS)20PN x 2 x 20 25,15 0,990 TP(OBS)20PN x 2 x 20 26,16 1,030 TP(OBS)20PN x 2 x 20 29,46 1,160 TP(OBS)20PN-24 1 x 2 x 18 9,27 0,365 TP(OBS)18PN-1 2 x 2 x 18 13,46 0,530 TP(OBS)18PN-2 3 x 2 x 18 14,99 0,590 TP(OBS)18PN-3 4 x 2 x 18 15,49 0 TP(OBS)18PN-4 5 x 2 x 18 18,03 0,710 TP(OBS)18PN-5 6 x 2 x 18 18,42 0,725 TP(OBS)18PN-6 7 x 2 x 18 18,42 0,725 TP(OBS)18PN-7 8 x 2 x 18 20,32 0,800 TP(OBS)18PN-8 9 x 2 x 18 22,86 0,900 TP(OBS)18PN-9 10 x 2 x 18 22,86 0,900 TP(OBS)18PN x 2 x 18 24,77 0,975 TP(OBS)18PN x 2 x 18 25,65 1,010 TP(OBS)18PN x 2 x 18 26,80 1,055 TP(OBS)18PN x 2 x 18 27,69 1,090 TP(OBS)18PN x 2 x 18 28,83 1,135 TP(OBS)18PN x 2 x 18 32,77 1,290 TP(OBS)18PN-24 2 x 2 x 16 14,61 0,575 TP(OBS)16PN-2 3 x 2 x 16 15,37 0,605 TP(OBS)16PN-3 4 x 2 x 16 16,64 0,655 TP(OBS)16PN-4 5 x 2 x 16 18,42 0,725 TP(OBS)16PN-5 6 x 2 x 16 19,05 0,750 TP(OBS)16PN-6 7 x 2 x 16 19,05 0,750 TP(OBS)16PN-7 8 x 2 x 16 21,08 0,830 TP(OBS)16PN-8 10 x 2 x 16 24,64 0,970 TP(OBS)16PN-10

22 gnfdaxxx Page 10 of x 2 x 16 x 2 x 20 x 2 x 24 x 2 x 16 25,53 1,005 TP(OBS)16PN ,45 1,120 TP(OBS)16PN ,72 1,170 TP(OBS)16PN ,53 1,320 TP(OBS)16PN-24 2 x 2 x 14 16,00 0,630 TP(OBS)14PN-2 3 x 2 x 14 16,76 0,660 TP(OBS)14PN-3 4 x 2 x 14 18,29 0,720 TP(OBS)14PN-4 5 x 2 x 14 20,32 0,800 TP(OBS)14PN-5 6 x 2 x 14 21,08 0,830 TP(OBS)14PN-6 7 x 2 x 14 21,08 0,830 TP(OBS)14PN-7 8 x 2 x 14 23,88 0,940 TP(OBS)14PN-8 10 x 2 x 14 26,92 1,060 TP(OBS)14PN x 2 x 14 28,19 1,110 TP(OBS)14PN x 2 x 14 31,50 1,240 TP(OBS)14PN x 2 x 14 33,02 1,300 TP(OBS)14PN x 2 x 14 38,86 1,530 TP(OBS)14PN-24 3 x 20 8,76 0,345 C20(OS)PN-3 4 x 20 9,53 0,375 C20(OS)PN-4 5 x 20 10,29 0,405 C20(OS)PN-5 6 x 20 10,92 0,430 C20(OS)PN-6 3 x 18 9,14 0,360 C18(OS)PN-3 4 x 18 9,91 0,390 C18(OS)PN-4 5 x 18 10,67 0,420 C18(OS)PN-5 6 x 18 11,43 0,450 C18(OS)PN-6 7 x 18 11,43 0,450 C18(OS)PN-7 12 x 18 15,24 0,600 C18(OS)PN x 18 18,42 0,725 C18(OS)PN x 18 20,45 0,805 C18(OS)PN-25 3 x 16 9,40 0,370 C16(OS)PN-3 4 x 16 10,29 0,405 C16(OS)PN-4 5 x 16 11,30 0,445 C16(OS)PN-5 6 x 16 12,07 0,475 C16(OS)PN-6

23 gnfdaxxx Page 11 of x 16 17,27 0,680 C16(OS)PN x 16 17,78 0,700 C16(OS)PN-15 3 x 14 10,54 0,415 C14(OS)PN-3 4 x 14 11,43 0,450 C14(OS)PN-4 5 x 14 12,45 0,490 C14(OS)PN-5 6 x 14 13,21 0,520 C14(OS)PN-6 7 x 14 13,21 0,520 C14(OS)PN-7 14 x 14 18,16 0,715 C14(OS)PN x 14 20,07 0,790 C14(OS)PN x 14 25,78 1,015 C14(OS)PN x 14 31,12 1,225 C14(OS)PN x 14 33,66 1,325 C14(OS)PN x 14 42,42 1,670 C14(OS)PN-91 4 x 5, ,73 0,580 C10(OS)PN-4 3 x 20 9,53 0,375 C20(OBS)PN-3 4 x 20 10,16 0,400 C20(OBS)PN-4 5 x 20 11,05 0,435 C20(OBS)PN-5 6 x ,470 C20(OBS)PN-6 3 x 18 9,91 0,390 C18(OBS)PN-3 4 x 18 10,67 0,420 C18(OBS)PN-4 5 x 18 11,43 0,450 C18(OBS)PN-5 6 x 18 12,19 0,480 C18(OBS)PN-6 7 x 18 12,19 0,480 C18(OBS)PN-7 12 x 18 15,49 0 C18(OBS)PN x 18 19,18 0,755 C18(OBS)PN x 18 21,21 0,835 C18(OBS)PN-25 3 x 16 10,16 0,400 C16(OBS)PN-3 4 x 16 11,05 0,435 C16(OBS)PN-4 5 x 16 12,07 0,475 C16(OBS)PN-5 6 x 16 12,83 0,505 C16(OBS)PN-6 12 x 16 16,26 0,640 C16(OBS)PN x 16 18,03 0,710 C16(OBS)PN-15 2 x 14 10,41 0,410 C14(OBS)PN-2 3 x 14 11,05 0,435 C14(OBS)PN-3 4 x 14 12,19 0,480 C14(OBS)PN-4 5 x 14 12,95 0,510 C14(OBS)PN-5

24 gnfdaxxx Page 12 of 13 6 x 14 13,72 0,540 C14(OBS)PN-6 7 x 14 13,72 0,540 C14(OBS)PN-7 14 x 14 18,42 0,725 C14(OBS)PN x 14 20,57 0,810 C14(OBS)PN x 14 26,54 1,045 C14(OBS)PN x 14 31,37 5 C14(OBS)PN x 14 34,42 1,355 C14(OBS)PN x 14 43,18 1,700 C14(OBS)PN-91 4 x 5, ,49 0 C10(OBS)PN-4 Application/Limitation The cable may be installed and sized according to IEC , except for the 2 conditions listed below. 1. Cables with flexible rope stranded conductors are to be installed on continuous cable trays (vented or non-vented) such as to prevent undue sag, and if horizontal, on the top of the tray giving support of the cable, when used for permanent installation. Cables intended for flexing service may be installed on festooned systems or articulating cableways. 2. Cable ends with flexible rope stranded conductors are to be terminated using approved compression terminals intended and designed for these conductors. The requirements of SOLAS Amendments 1981 Chapter II-1, Part D, Reg. 45, 5.2 (provision to be taken to limit Fire Propagation along Bunches of Cables or Wires) are fulfilled without any additional measures. Type Approval documentation Tests carried out Test according to IEEE 45 (1993) Draft, IEEE 45 (1998), IEEE (2001) and IEC cat. A. Marking of product Draka 32 BOSTRIG-125 Type P - Type designation - Number and size of conductors - Voltage. Certificate retention survey The scope of the retention/renewal survey is to verify that the conditions stipulated for the Type approval is complied with and that no alterations are made to the product design or choice of materials. The main elements of the survey are: Inspection on factory samples, selected at random from the production line (where practicable)

25 gnfdaxxx Page 13 of 13 Results from Production Sample Tests (PST) and Routines (RT) checked (if not available tests according to PST and RT to be carried out) Review of type approval documentation Review of possible change in design, materials and performance Ensuring traceability between manufacturer's product type marking and Type Approval Certificate. Survey to be performed at least every second year. END OF CERTIFICATE Notice: This Certificate is subject to terms and conditions overleaf. Any significant change in design or construction may render this Certificate invalid. If any person suffers loss or damage which is proved to have been caused by any negligent act or omission of Det Norske Veritas, then Det Norske Veritas shall pay compensation to such person for his proved direct loss or damage. However, the compensation shall not exceed an amount equal to ten times the fee charged for the service in question, provided that the maximum compensation shall never exceed USD 2 million.in this provision "Det Norske Veritas" shall mean the Foundation Det Norske Veritas as well as all its subsidiaries, directors, officers, employees, agents and any other acting on behalf of Det Norske Veritas. DET NORSKE VERITAS AS VERITASVEIEN 1, 1322 HØVIK, NORWAY TEL: (+47) FAX: (+47)

26 enfdaxxx Page 1 of 9 DET NORSKE VERITAS TYPE APPROVAL CERTIFICATE CERTIFICATE NO. E-8792 This Certificate consists of 5 pages This is to certify that the Electric Cable, Power Current with type designation(s) BOSTRIG-125 Type P, DPN, TPN, QPN and C..PN, BOSTRIG-125 Type P, SP2KV(HD) Holder of certificate Draka Marine, Oil & Gas International Houston, TX 77032, United States is found to comply with Det Norske Veritas' Rules for Classification of Ships, High Speed & Light Craft and Det Norske Veritas' Offshore Standards IEEE IEEE IEC ( ) Application Power, Lighting and Control Type Voltage class (kv) Temp. class ( C)

27 enfdaxxx Page 2 of 9 BOSTRIG-125 Type P, DPN, TPN, QPN and 0,6/1 95 C..PN BOSTRIG-125 Type P, SP2KV(HD) 2 95 Place and date This Certificate is valid until Høvik, for Det Norske Veritas AS Name and place of manufacturer: Product description Marit Laumann Local Office Ivar Bull Head of Section DNV New York Surveyor Draka Cableteq USA North Dighton MA USA Construction: Conductor: Tinned stranded copper Insulation: XLPO Filler: Flame Retardant, non hygroscopic (as needed) Outer sheath: SP1 (type N) Number of Overall cores x diameter conductor cross-section mm 2 AWG/MCM mm Inches Type designation 1 x 112,6 4/0 20,83 0,820 SP2KV(HD)-4/0 1 x 133, ,10 0,870 SP2KV(HD) x 158, ,75 0,935 SP2KV(HD) x 189, ,53 1,005 SP2KV(HD) x 225, ,31 1,075 SP2KV(HD) x 271, ,35 1,195 SP2KV(HD) x 327, ,89 1,295 SP2KV(HD) x ,18 1,385 SP2KV(HD)-777

28 enfdaxxx Page 3 of 9 393,8 1 x 562, ,51 1,595 SP2KV(HD) x 7, ,99 0,590 DPN-8 2 x 12,5 6 17,91 0,705 DPN-6 2 x 18,6 5 20,57 0,810 DPN-5 2 x 21,5 4 22,10 0,870 DPN-4 2 x 25,6 3 23,37 0,920 DPN-3 2 x 30,7 2 25,02 0,985 DPN-2 2 x 46,0 1 29,21 1,150 DPN-1 2 x 56,3 1/0 32,00 1,260 DPN-1/0 2 x 66,5 2/0 33,53 1,320 DPN-2/0 2 x 92,1 3/0 39,62 1,560 DPN-3/0 2 x 112,6 4/0 42,16 1,660 DPN-4/0 2 x 133, ,48 1,830 DPN x 158, ,91 1,965 DPN x 189, ,47 2,105 DPN x 225, ,02 2,245 DPN x 271, ,37 2,495 DPN x 327, ,45 2,695 DPN x 393, ,66 2,900 DPN x 7, ,88 0,625 TPN-8 3 x 12,5 6 19,05 0,750 TPN-6 3 x 18,6 5 22,61 0,890 TPN-5 3 x 21,5 4 23,50 0,925 TPN-4 3 x 25,6 3 24,77 0,975 TPN-3 3 x 30,7 2 26,54 1,045 TPN-2 3 x 46,0 1 31,12 1,225 TPN-1 3 x 56,3 1/0 34,04 1,340 TPN-1/0 3 x 66,5 2/0 36,58 1,440 TPN-2/0 3 x 92,1 3/0 42,29 1,665 TPN-3/0 3 x 112,6 4/0 45,72 1,800 TPN-4/0 3 x 133, ,53 1,950 TPN x 158, ,21 2,095 TPN x 189, ,02 2,245 TPN x 225, ,60 2,425 TPN x 271, ,56 2,660 TPN x 327, ,79 2,905 TPN-646

29 enfdaxxx Page 4 of 9 3 x 393, ,61 3,095 TPN x 7, ,53 0,690 FPN-8 4 x 12,5 6 20,83 0,820 FPN-6 4 x 18,6 5 24,89 0,980 FPN-5 4 x 21,5 4 25,91 1,020 FPN-4 4 x 25,6 3 27,43 1,080 FPN-3 4 x 30,7 2 29,46 1,160 FPN-2 4 x 46,0 1 34,54 1,360 FPN-1 4 x 56,3 1/0 38,35 1,510 FPN-1/0 4 x 66,5 2/0 40,39 1,590 FPN-2/0 4 x 92,1 3/0 47,63 1,875 FPN-3/0 4 x 112,6 4/0 50,67 1,995 FPN-4/0 4 x 133, ,99 2,165 FPN x 158, ,82 2,355 FPN x 189, ,14 2,525 FPN x 225, ,45 2,695 FPN x 271, ,95 2,990 FPN x 327, ,04 3,230 FPN x 393, ,50 3,445 FPN x 7, ,30 0,760 QPN-8 5 x 12,5 6 24,26 0,955 QPN-6 5 x 18,6 5 27,43 1,080 QPN-5 5 x 21,5 4 28,58 1,125 QPN-4 5 x 25,6 3 30,35 1,195 QPN-3 5 x 30,7 2 32,51 1,280 QPN-2 5 x 46,0 1 39,75 1,565 QPN-1 5 x 56,3 1/0 43,56 1,715 QPN-1/0 5 x 66,5 2/0 45,47 1,790 QPN-2/0 5 x 92,1 3/0 52,71 2,075 QPN-3/0 5 x 112,6 4/0 56,13 2,210 QPN-4/0 7 x 7, ,23 0,875 7PN-8 4 x 3, ,94 0,785 [FP-12/C(OS)14P-4] N-8 4 x 14 shielded 4 x 7, ,15 0,990 [FP-8/C(OS)14P-4]N- 8 4 x 14 shielded 4 x 21,5 4 31,24 0 [FP-4/C(OS)14P-4]N- 8 4 x 14 shielded

30 enfdaxxx Page 5 of 9 4 x 30,7 2 34,04 1,340 [FP-2/C(OS)14P-4]N- 8 4 x 14 shielded 4 x 46,0 1 40,13 1,580 [FP-1/C(OS)14P-4]N- 8 4 x 14 shielded 2 x 18,6 5 41,66 1,640 [DP-2/FP-8/C14P-26/ 4 x 7,57 8 TP(I/S)14P-3]N x 14 3 x2 x 14 shielded 7 x 6,0 9 36,32 1,430 [C9P-7/C13P-7/ 7 x 2,5 13 C15P-12]N x 1, x 18 8,64 0,340 C18PN-2 3 x 18 9,14 0,360 C18PN-3 4 x 18 9,91 0,390 C18PN-4 5 x 18 10,80 0,425 C18PN-5 6 x 18 11,68 0,460 C18PN-6 7 x 18 11,68 0,460 C18PN-7 8 x 18 12,45 0,490 C18PN-8 10 x 18 14,48 0,570 C18PN x 18 14,86 0,585 C18PN x 18 16,76 0,660 C18PN x 18 18,16 0,715 C18PN x 18 20,07 0,790 C18PN x 18 22,23 0,875 C18PN x 18 23,88 0,940 C18PN x 18 26,80 1,055 C18PN x 18 26,80 1,055 C18PN x 18 29,59 1,165 C18PN x 18 35,31 1,390 C18PN-91 2 x 16 9,02 0,355 C16PN-2 3 x 16 9,40 0,370 C16PN-3 4 x 16 10,16 0,400 C16PN-4 5 x 16 11,18 0,440 C16PN-5 6 x 16 12,07 0,475 C16PN-6 7 x 16 12,07 0,475 C16PN-7

31 enfdaxxx Page 6 of 9 8 x 16 13,72 0,540 C16PN-8 10 x 16 15,11 0,595 C16PN x 16 15,49 0 C16PN x 16 17,15 0,675 C16PN x 16 18,03 0,710 C16PN x 16 18,92 0,745 C16PN x 16 19,94 0,785 C16PN x 16 21,34 0,840 C16PN x 16 23,24 0,915 C16PN x 16 25,02 0,985 C16PN x 16 27,94 1,100 C16PN x 16 30,99 1,220 C16PN x 16 37,59 1,480 C16PN-91 2 x 14 9,65 0,380 C14PN-2 or DPN-14 3 x 14 9,91 0,390 C14PN-3 or TPN-14 4 x 14 10,92 0,430 C14PN-4 or FPN-14 5 x 14 12,07 0,475 C14PN-5 or QPN-14 6 x 14 13,08 0,515 C14PN-6 7 x 14 13,08 0,515 C14PN-7 8 x 14 14,22 0,560 C14PN-8 10 x 14 16,51 0,650 C14PN x 14 17,02 0,670 C14PN x 14 17,91 0,705 C14PN x 14 18,80 0,740 C14PN x 14 19,81 0,780 C14PN x 14 20,83 0,820 C14PN x 14 24,13 0,950 C14PN x 14 25,53 1,005 C14PN x 14 27,43 1,080 C14PN x 14 30,86 1,215 C14PN x 14 34,16 1,345 C14PN x 14 41,91 1,650 C14PN-91

32 enfdaxxx Page 7 of 9 2 x 3, ,80 0,425 C12PN-2 or DPN-12 3 x 3, ,18 0,440 C12PN-3 or TPN-12 4 x 3, ,07 0,475 C12PN-4 or FPN-12 5 x 3, ,34 0,525 C12PN-5 or QPN-12 6 x 3, ,48 0,570 C12PN-6 7 x 3, ,48 0,570 C12PN-7 8 x 3, ,75 0,620 C12PN-8 10 x 12 18,29 0,720 C12PN-10 3,08 12 x 12 18,92 0,745 C12PN-12 3,08 16 x 12 21,97 0,865 C12PN-16 3,08 20 x 12 24,26 0,955 C12PN-20 3,08 24 x 12 26,92 1,060 C12PN-24 3,08 30 x 12 28,45 1,120 C12PN-30 3,08 37 x 12 30,73 1,210 C12PN-37 3,08 44 x 12 34,42 1,355 C12PN-44 3,08 60 x 12 39,75 1,565 C12PN-60 3,08 91 x 3, ,75 1,880 C12PN-91 2 x 5, ,45 0,490 C10PN-2 or DPN-10 3 x 5, ,21 0,520 C10PN-3 or TPN-10 4 x 5, ,35 0,565 C10PN-4 or FPN-10 5 x 5, ,75 0,620 C10PN-5 or QPN-10 6 x 5, ,15 0,675 C10PN-6 7 x 5, ,15 0,675 C10PN-7 8 x 5, ,54 0,730 C10PN-8 9 x 5, ,35 0,880 C10PN-9 10 x 5, ,73 0,895 C10PN-10 Application/Limitation When HD cables are installed outside enclosure, precautions are to be taken to avoid mechanical damage. The cable may be installed and sized according to IEC , except for the 2 conditions listed below. 1. Cables with flexible rope stranded conductors are to be installed on continuous cable trays (vented or non-vented) such as to prevent undue sag, and if horizontal, on the top of the tray giving support of the cable, when used for permanent installation. Cables intended

33 enfdaxxx Page 8 of 9 for flexing service may be installed on festooned systems or articulating cableways. 2. Cable ends with flexible rope stranded conductors are to be terminated using approved compression terminals intended and designed for these conductors. The requirements of SOLAS Amendments 1981 Chapter II-1, Part D, Reg. 45, 5.2 (provision to be taken to limit Fire Propagation along Bunches of Cables or Wires) are fulfilled without any additional measures. Type Approval documentation Tests carried out Marking of product Test according to IEEE 45 (1993) Draft, IEEE 45 (1998), IEEE 1580 (2001) and IEC cat. A. Draka 32 BOSTRIG-125 Type P - Type designation - Number and size of conductors - Voltage. Certificate retention survey The scope of the retention/renewal survey is to verify that the conditions stipulated for the Type approval is complied with and that no alterations are made to the product design or choice of materials. The main elements of the survey are: Inspection on factory samples, selected at random from the production line (where practicable) Results from Production Sample Tests (PST) and Routines (RT) checked (if not available tests according to PST and RT to be carried out) Review of type approval documentation Review of possible change in design, materials and performance Ensuring traceability between manufacturer's product type marking and Type Approval Certificate. Survey to be performed at least every second year. END OF CERTIFICATE Notice: This Certificate is subject to terms and conditions overleaf. Any significant change in design or construction may render this Certificate invalid.

34 enfdaxxx Page 9 of 9 If any person suffers loss or damage which is proved to have been caused by any negligent act or omission of Det Norske Veritas, then Det Norske Veritas shall pay compensation to such person for his proved direct loss or damage. However, the compensation shall not exceed an amount equal to ten times the fee charged for the service in question, provided that the maximum compensation shall never exceed USD 2 million.in this provision "Det Norske Veritas" shall mean the Foundation Det Norske Veritas as well as all its subsidiaries, directors, officers, employees, agents and any other acting on behalf of Det Norske Veritas. DET NORSKE VERITAS AS VERITASVEIEN 1, 1322 HØVIK, NORWAY TEL: (+47) FAX: (+47)

35 Part 1B Subject: Electrical Equipment (Not Environmentally Tested) Product: Cables Power (Part 1B) Producer/Licence No. Description of Product Type Details of Approval Application Remarks Cert. No. Draka Cableteq USA, 22 Joseph E. Warner Boulevard, North Dighton, MA 02764, United States of America (USA). Bostrig 125 Type P (600/1000V) Flame retardant, single and multicore power and control cables, crosslinked polyolefin insulated, actic gradeneoprene sheathed. With or without bronze or aluminium braid and arctic grade Neoprene outer sheath Voltage rating: Maximum conductor temperature: 0.6kV, 2kV 95deg. C General fixed power and control wiring for ships and offshore installations Expires: 29 November 2010 IEEE-1580 IEEE -45 UL1309/CSA 245 IEC Category A See manufacturer s literature for cable sizes 95/60161(E3) LLOYD'S REGISTER, 2005 NOTICE AND TERMS OF USE Lloyd's Register, its affiliates and subsidiaries and their respective officers, employees or agents are, individually and collectively, referred to in this clause as the Lloyd's Register Group. The Lloyd's Register Group assumes no responsibility and shall not be liable to any person for any loss, damage or expense caused by reliance on the information or advice in this document or howsoever provided, unless that person has signed a contract with the relevant Lloyd's Register Group entity for the provision of this information or advice and in that case any responsibility or liability is exclusively on the terms and conditions set out in that contract. 1

36 Part 1B Subject: Electrical Equipment (Not Environmentally Tested) Product: Cables Power (Part 1B) Producer/Licence No. Description of Product Type Details of Approval Application Remarks Cert. No. Draka Cableteq USA, 22 Joseph E. Warner Boulevard, North Dighton, MA 02764, United States of America (USA). Bostrig 125 Type P (600V and 2000V) Flame retardant, twisted pair and twisted triple instrumentation and communication cables, crosslinked polyolefin insulated, actic grade Neoprene sheathed. With or without bronze or aluminium braid and arctic grade Neoprene outer sheath Voltage rating: Maximum conductor temperature: 0.6kV and 2kV 95deg. C Instrumentation and communication wiring for ships and offshore installations Expires: 29 November 2010 Standards IEEE-1580 IEEE -45 UL1309/CSA 245 IEC Category A See manufacturer s literature for cable sizes 95/60162(E3) LLOYD'S REGISTER, 2005 NOTICE AND TERMS OF USE Lloyd's Register, its affiliates and subsidiaries and their respective officers, employees or agents are, individually and collectively, referred to in this clause as the Lloyd's Register Group. The Lloyd's Register Group assumes no responsibility and shall not be liable to any person for any loss, damage or expense caused by reliance on the information or advice in this document or howsoever provided, unless that person has signed a contract with the relevant Lloyd's Register Group entity for the provision of this information or advice and in that case any responsibility or liability is exclusively on the terms and conditions set out in that contract. 1

37 Certificate Number: 03-HS290310/2-PDA Confirmation of Product Type Approval 04/MAY/2009 Please refer to the "Service Restrictions" shown below to determine if Unit Certification is required for this product. This is to certify that, pursuant to the Rules of the American Bureau of Shipping (ABS), the manufacturer of the below listed product held a valid Manufacturing Assessment (MA) with expiration date of 30/JUL/2013. The continued validity of the Manufacturing Assessment is dependent on completion of satisfactory audits as required by the ABS Rules. And; a Product Design Assessment (PDA) valid until 09/AUG/2011 subject to continued compliance with the Rules or standards used in the evaluation of the product. The above entitle the product to be called Product Type Approved. The Product Design Assessment is valid for products intended for use on ABS classed vessels, MODUs or facilities which are in existence or under contract for construction on the date of the ABS Rules used to evaluate the Product. ABS makes no representations regarding Type Approval of the Product for use on vessels, MODUs or facilities built after the date of the ABS Rules used for this evaluation. Due to wide variety of specifications used in the products ABS has evaluated for Type Approval, it is part of our contract that; whether the standard is an ABS Rule or a non-abs Rule, the Client has full responsibility for continued compliance with the standard. Presented to: AMERCABLE INCORPORATED 350 BAILEY RD EL DORADO AR United States AMERCABLE INCORPORATED Model Name(s): GEXOL & CIR Intended Service: Description: Ratings: Electrical Cable for use on board marine and offshore vessels and structures Power Distribution Cables: 2kV max., Single conductor- sizes 18AWG through 1111MCM; Multiconductor- 2 to 4 conductors, sizes 20AWG through 777MCM. Control Cables: 1000V maximum, multiconductor, sizes 20AWG through 10AWG. Instrument Cables: 1000V maximum, unshielded & shielded (individual and/or overall shield) aluminum/polyethylene terephthalate tape or braided copper, pairs/triads, sizes 20AWG through 14AWG. Marine shipboard cable employing type X110 (Type X90 when used with Type T jacket) cross-linked polyolefin insulation Amercable GEXOL or GEXOL120X, jacket type N neoprene or type CPE or type TPPO or Type T or type NBR/PVC (ester-based drilling mud resistant), with optional armor- aluminum or tinned copper or bronze braid and optional jacket over the armor type N neoprene or type CPE or type TPPO or Type T or type NBR/PVC (ester-based drilling mud resistant). In addition to approval as a marine cable, model CIR is also approved as Crush & Impact Resistant NEC type TC cable suitable for open wiring (NEC article ). Distribution Cables: Multiconductor- 3 or 4 conductors, sizes 18AWG through 1000MCM (for cable with jacket constructed of polyolefin jacket compound Type TPPO or Type T, sizes 4AWG or larger (for cable with jacket constructed of neoprene jacket compound CR 020X). Control Cables: Multiconductor, sizes 14AWG through 10AWG. Instrument Cables, size 18 & 16AWG. All cables have grounding conductor in accordance with Article of the NEC. UL Approved Marine Cable (UL 1309/CSA C22.2 No. 245):-Voltage Class: Max. 2kV. Ampacity: as per IEEE Std Table 25 Insulation Class Cross-linked Polyolefin Type 'P' 100 degrees C (XLPE Type 'X' 90 degrees C when used with 05/04/ :02:25 PM Copyright 2001 American Bureau of Shipping. All rights reserved. Page 1 of 2

38 Certificate Number: 03-HS290310/2-PDA Service Restrictions: Comments: Notes / Documentation: Term of Validity: ABS Rules: National Standards: International Standards: Government Authority: EUMED: Others: Type T jacket); for offshore applications the cable may be 110 degree C (90degree C with Type T jacket) for industrial/production system loads. Flame Tests IEEE Std 1202 & IEC Cat. A/F. Arctic Rating: (- 40) degrees C (cold impact & bending) for cable with CPE jacket (compound 4200); cable with Type N Neoprene or Type TPPO jacket is rated - 40 degrees C for cold bending & - 35 degrees C for cold impact; cables with Type NBR/PVC (ester-based drilling mud resistant) jacket is rated -40 degrees C for cold bending. The cables are also constructed in accordance with IEEE Std (except for cable with TPPO jacket). Additional Listing as UL Approved NEC Type TC Cable, with 'exposed run':-voltage Class: Max. 2kV. Ampacity: in accordance with article of the NEC, Insulation Class 90 degrees C or 75 degrees C depending upon type of insulation (marked on the cable). Cable with jacketing material Type NBR/PVC is extremely resistant to ester-based drilling mud. Unit Certification is not required for this product. If the manufacturer or purchaser's request an ABS Certificate for compliance with a specification or standard, the specification or standard, including inspection standards and tolerances, must be clearly defined. Cable Model CIR is to be installed in accordance with NEC Article 336 for NEC installations or installed in accordance with IEEE 45 for Offshore applications. Cables size14 AWG 7/C cable, complies with NEK606 for the Mud Resistant NBR/PVC compound addition as per UL letter reference: E111461; PTL/C of 14 October 2002 Certificate 03-HS290310/2-PDA, dated 10/Aug/2006 is valid for 5 years from date of issue or until the applicable Rules or standards are revised (whichever occurs first). Product use on or after 1 January 2007, will be subject to compliance with the ABS Rules or specifications in effect when the vessel, MODU or facility is contracted Steel Vessel Rules 1-1-4/7.7, 4-8-3/9.1, 9.5, 9.9 & 9.17 & 2006 MODU Rules 4-3-4/13.1.1, & UL 1309, UL 1277, UL File E11161, CSA C22.2 No. 245, IEEE Std , IEEE Std , IEEE 1202 IEC (flame retardancy) e cable meets the requirements of USCG 46CFR Manufacturer's Specifications ABS Programs ABS has used due diligence in the preparation of this certificate and it represents the information on the product in the ABS Records as of the date and time the certificate was printed. Type Approval requires Drawing Assessment, Prototype Testing and assessment of the manufacturer's quality assurance and quality control arrangements. Limited circumstances may allow only Prototype Testing to satisfy Type Approval. The approvals of Drawings and Products remain valid as long as the ABS Rule, to which they were assessed, remains valid. ABS cautions manufacturers to review and maintain compliance with all other specifications to which the product may have been assessed. Further, unless it is specifically indicated in the description of the product; Type Approval does not necessarily waive witnessed inspection or survey procedures (where otherwise required) for products to be used in a vessel, MODU or facility intended to be ABS classed or that is presently in class with ABS. Questions regarding the validity of ABS Rules or the need for supplemental testing or inspection of such products should, in all cases, be addressed to ABS. 05/04/ :02:25 PM Copyright 2001 American Bureau of Shipping. All rights reserved. Page 2 of 2

39 Part 1B Subject: Electrical Equipment (Not Environmentally Tested) Product: Cables Power (Part 1B) Producer/Licence No. Description of Product Type Details of Approval Application Remarks Cert. No. AmerCable, 350 Bailey Road, El Dorado, AR 71730, United States of America (USA) Tiger Brand Electric cable. One, three and four core power cable. Multicore control and instrumentation cable. Maximum voltage (V): 2000, single core 600, 3 & 4 & multicore Maximum temperature ( C): 95 Marine and offshore wiring, and general purpose wiring. Expires: 10 May 2009 Complies with: IEEE UL1309/CSA C22.2 No.245 IEC cat. A/F 91/60333(E6) LLOYD'S REGISTER, 2005 NOTICE AND TERMS OF USE Lloyd's Register, its affiliates and subsidiaries and their respective officers, employees or agents are, individually and collectively, referred to in this clause as the Lloyd's Register Group. The Lloyd's Register Group assumes no responsibility and shall not be liable to any person for any loss, damage or expense caused by reliance on the information or advice in this document or howsoever provided, unless that person has signed a contract with the relevant Lloyd's Register Group entity for the provision of this information or advice and in that case any responsibility or liability is exclusively on the terms and conditions set out in that contract. 1