GRUNDFOS DATA BOOKLET TP, TPD, TPE. In-line circulator pumps 60 Hz

Transcription

1 GRUNDFOS DATA BOOKLET TP, TPD, TPE In-line circulator pumps Hz

2 Contents Pump data Introduction Type key 5 Performance range Performance range, -pole, PN //1 Performance range, -pole, PN //1 7 Performance range, -pole, PN 5 Performance range, -pole, PN 5 9 Product range Product range, -pole, PN //1 Product range, -pole, PN //1 1 Product range, -pole, PN 5 1 Product range, -pole, PN 5 15 Operating conditions Pressure conditions 1 Ambient temperature 1 Pumped liquids Pumped liquids 17 Liquid temperature 17 List of pumped liquids 1 TP Series pumps Technical data Construction Materials Mechanical shaft seal 1 Connections 1 Features and benefits 1 TP Series 3 pumps Technical data Construction Materials Mechanical shaft seal Connections 3 Features and benefits 3 TP Series pumps Technical data Construction Materials Mechanical shaft seal 5 Connections 5 Features and benefits 5 TPE Series pumps Technical data Construction Applications Control options 7 Communication Communication with TPE pumps Speed regulation of TPE pumps Affinity equations 9 Motor data Motor 3 Motor protection 3 Electrical data, standard motors 31 Electrical data, motors with built-in frequency converter 3 Installation Mechanical installation 33 Electrical installation 3 Flanges for TP pumps Flange dimensions 3 Curve charts How to read the curve charts 39 Curve conditions Performance curves/technical data TP, TPD, TPE -pole, PN //1 TP, TPD, TPE, -pole, PN //1 5 TP, -pole, PN 5 TP, -pole, PN 5 Weights and shipping volume TP, TPD, TPE, -pole, PN //1 9 TP, TPD, TPE, -pole, PN //1 97 TP, -pole, PN 5 9 TP, -pole, PN 5 99

3 Contents Accessories Counter flanges Base plates 3 Blanking flanges Insulating kits 7 Sensors Potentiometer 9 R 9 G-LON interface 9 EMC filter 9 Minimum inlet pressure - NPSH TP, TPD -pole, PN //1 111 TP, TPD -pole, PN //1 11 TP Series, -pole, PN 5 11 TP Series, -pole, PN Further product documentation WebCAPS 11 WinCAPS 115 3

4 Pump data TP, TPD, TPE Introduction TP pumps are designed for applications such as district heating systems heating systems air-conditioning systems district cooling systems water supply industrial processes industrial cooling. Most of the pumps are available with either standard motors (TP and TPD) or electronically speed-controlled motors (TPE). The pumps are all single-stage, in-line centrifugal pumps with standard motor and mechanical shaft seal. The pumps are of the close-coupled type, i.e. pump and motor are separate units. Consequently, the pumps are less sensitive to impurities in the pumped liquid than similar pumps of the canned rotor type. TP pumps uncontrolled pumps The TP range is divided into the following four groups based on their construction: TP Series,, 3 and pumps. TP Series with flange connection DN 3 to DN and motor sizes from.1 to 3 kw. For further information, see page. TP Series 3 with flange connection DN 3 to DN and motor sizes from.55 to 55 kw. For further information, see page. TP Series with flange connection Grundfos offers two TP Series versions: bar version with DN 1 to DN flange and motor sizes from 37 to 13 kw. 5 bar version with DN to DN and motor sizes from 7.5 to 315 kw. For further information about TP Series pumps, see page. TPE pumps speed-controlled pumps Based on the construction and choice of material of TP pumps, Grundfos offers speed-controlled TPE Series pumps. TPE Series pumps The difference between the TP and the TPE Series pump range is the motor. The motors of TPE Series pumps have built-in frequency converter. Via an external signal (from a sensor or a controller), TPE Series pumps allow for any configuration and control method required: Constant pressure, constant temperature or constant flow. Note: TPE Series pumps are delivered without a differential-pressure sensor. TPE Series pumps are based on TP Series and 3 pumps. The pump materials are the same as those of the TP pump range. For further information, see page. Why select a TPE pump? A TPE pump with electronic, speed-controlled adaptation of performance offers these obvious benefits: energy savings increased comfort control and monitoring of the pump performance communication with the pump. ATEX-approved TP pumps On request, Grundfos offers TP and TPD pumps with ATEX-approval. All ATEX-approved TP pumps are in accordance with Council directive 9/9/EC (Group II, category 3). High-efficiency motors TP pumps are fitted with high-efficiency motors. - and -pole TP pumps with motor sizes from 1.1 to 9 kw are fitted with high-efficiency motors (EFF1). EFF1 is the highest efficiency class defined by CEMEP.

5 Pump data TP, TPD, TPE Type key Example TP E D 5-1 / -A -F -A -AUUE Pump range Electronically speed controlled pump Series Twin-head pump Nominal diameter of suction and discharge ports (DN) Maximum head [dm] Pole number Code for pump version: A = Basic version I = PN flange X = Special version Code for pipework connection: F = DIN flange O = Union Code for materials: A = Basic version Z = Bronze pump housing and motor stool B = Bronze impeller Code for shaft seal (incl. other plastic and rubber components in the pump except the neck ring) Codes for shaft seal Example B B U E Grundfos type designation A = O-ring seal with fixed seal driver B = Rubber bellows seal D = O-ring seal, balanced G = Bellows seal with reduced seal faces R = O-ring seal with reduced seal faces Material of rotating face A = Carbon, antimony-impregnated B = Carbon, synthetic resin-impregnated Q = Silicon carbide U = Tungsten carbide Material of stationary seat B = Carbon, synthetic resin-impregnated Q = Silicon carbide U = Tungsten carbide Material of secondary seal E = EPDM P = NBR rubber V = FKM 5

6 Performance range TP, TPD, TPE -pole, PN //1 Performance range, -pole, PN //1 (See page for performance curves) p [kpa] H TM 51 1 TP(D), TPE PN -1, -pole, Hz Q [m³/h] Q [l/s] Note: All QH curves apply to single-head pumps. For further information about curve conditions, see page. The hatched area shows the performance range of TPE pumps.

7 Performance range TP, TPD, TPE -pole, PN //1 Performance range, -pole, PN //1 (See page 5 for performance curves) p [kpa] 7 H TM TP(D), TPE PN -1, -pole, Hz Q [m³/h] Q [l/s] Note: All QH curves apply to single-head pumps. For further information about curve conditions, see page. The hatched area shows the performance range of TPE pumps. 7

8 Performance range TP -pole, PN 5 Performance range, -pole, PN 5 (See page for performance curves) p [kpa] H TM 7 5 TP PN 5, -pole, Hz Q [m³/h] Q [l/s]

9 Performance range TP -pole, PN 5 Performance range, -pole, PN 5 (See page for performance curves) p [kpa] H TM 73 5 TP PN 5, -pole, Hz Q [m³/h] Q [l/s] 9

10 Product range TP, TPD, TPE Product range, -pole, PN //1 Pump type Design Shaft seal Pressure stage Materials Standard motor TPE Series (1 TP Series TP Series 3 TP Series BUBE AUUE RUUE BAQE BQQE GQQE DBUE PN / combination flange PN PN 1 PN 5 Electronically speed controlled motor Pump housing Impeller Voltage [V] Voltage [V] Cast iron EN-GJL- Nodular cast iron EN-GJS--1 Bronze Stainless steel Cast iron Nodular cast iron EN-GJS--15 Bronze TP 3-/.37 TP 3-1/.55 TP 3-/.75 3 x -55 ΔV/ 3 x 3- YV P TP 3-/ 1.1 TP 3-33/ 1.5 TP, TPD 3-3/... TP, TPD 3-3/ TP, TPD 3-/... TP, TPD 3-5/ TP, TPD 3-/ TP, TPD 3-/ TP -/.55 TP -1/.75 TP -/ 1.1 TP -7/ 1.5 TP -33/. TP -39/ 3. TP, TPD -37/... TP, TPD -/ TP, TPD -5/ TP, TPD -7/ TP, TPD -/ TP, TPD -93/ TP -/.55 TP -1/ 1.1 TP -/ 1.5 TP, TPD -/... TP, TPD -3/ TP, TPD -3/... TP, TPD -/ TP, TPD -/ TP, TPD -5/ TP, TPD -7/ TP, TPD -79/ TP, TPD -/... TP, TPD -/ TP 5-/ 1.1 TP 5-1/ 1.5 TP 5-/. TP, TPD 5-/ TP, TPD 5-/... TP, TPD 5-3/ TP, TPD 5-39/ TP, TPD 5-/ TP, TPD 5-5/ TP, TPD 5-3/ TP, TPD 5-7/... TP, TPD 5-9/ x -77 ΔV/ 3 x 3- YV P 3 x 3- ΔV P 3 x 3- ΔV/ 3 x -9 YV ( P 3 x 3-15 V P 3 x 3- V P

11 Product range TP, TPD, TPE Pump type TP, TPD 5-/ TP -1/ 3. TP, TPD -/... TP, TPD -/ TP, TPD -9/ TP, TPD -33/ TP, TPD -/ TP, TPD -/ TP, TPD -53/... TP, TPD -/ TP, TPD -7/ TP, TPD -3/ TP, TPD -3/ TP, TPD -37/ TP, TPD -3/ TP, TPD -3/... TP, TPD -53/ TP, TPD -3/ TP, TPD -7/ Standard Design Shaft seal Pressure stage Materials Standard motor TPE Series (1 TP Series TP Series 3 TP Series BUBE AUUE RUUE BAQE BQQE GQQE DBUE PN / combination flange PN PN 1 PN 5 1 TPE pumps are not available in twin-head versions. -pole motors above 7.5 kw can be operated at 3 x -9 YV. Smaller motor sizes cannot. Electronically speed controlled motor Pump housing Impeller Voltage [V] Voltage [V] Cast iron EN-GJL- Nodular cast iron EN-GJS--1 Bronze Stainless steel Cast iron Nodular cast iron EN-GJS--15 Bronze 3 x -55 ΔV/ 3 x 3- YV P 3 x -77 ΔV/ 3 x 3- YV P 3 x 3- ΔV P 3 x 3- ΔV/ 3 x -9 YV ( P 3 x 3-15 V P 3 x 3- V P 11

12 Product range TP, TPD, TPE Product range, -pole, PN //1 Pump type Design Shaft seal Pressure stage Materials Standard motor TPE Series (1 TP Series TP Series 3 TP Series BUBE AUUE RUUE BAQE BQQE GQQE DBUE PN / combination flange PN PN 1 PN 5 Electronically speed controlled motor Pump housing Impeller Voltage [V] Voltage [V] Cast iron EN-GJL- Nodular cast iron EN-GJS--1 Bronze Stainless steel Cast iron TP 3-/.1 TP 3-/.5 TP, TPD 3-1/.55 TP, TPD 3-1/.75 TP, TPD 3-19/ TP -/.5 TP -/.55 TP, TPD -1/.75 TP, TPD -1/ TP, TPD -19/ TP, TPD -/... TP -/.5 TP -/.55 TP, TPD -1/.75 TP, TPD -1/ TP, TPD -1/ TP, TPD -19/... TP, TPD -/ TP, TPD -7/... TP, TPD -3/ TP 5-/.37 Nodular cast iron EN-GJS--15 Bronze 3 x -55 ΔV/ 3 x 3- YV P TP 5-/ 1.1 TP, TPD 5-13/ TP, TPD 5-1/... TP, TPD 5-19/ TP, TPD 5-3/... TP, TPD 5-3/ TP, TPD 5-33/ TP -/.75 TP -/ TP, TPD -1/... TP, TPD -1/ TP, TPD -17/... TP, TPD -3/ TP, TPD -/ TP, TPD -3/ TP, TPD -/ TP, TPD -/ TP, TPD -5/... TP -/ TP -/.. TP, TPD -/ TP, TPD -13/... TP, TPD -17/ TP, TPD -/ TP, TPD -/ TP, TPD -9/ TP, TPD -3/ x -77 ΔV/ 3 x 3- YV P 3 x 3- ΔV P 3 x 3- ΔV/ 3 x -9 YV( P 3 x 3-15 V P 3 x 3- V P 1

13 Product range TP, TPD, TPE Pump type TP, TPD -39/... TP, TPD -7/ TP, TPD 15-13/ TP, TPD 15-1/ TP, TPD 15-/ TP, TPD 15-/ TP, TPD 15-3/ TP, TPD 15-3/... TP, TPD 15-3/ TP, TPD 15-9/ TP, TPD 1-1/ TP, TPD 1-/ TP, TPD 1-/... TP, TPD 1-3/ 3. TP 1-3/ 3. TP 1-3/ 37. TP 1-/ 37. TP 1-/ 5. TP 1-9/ 55. TP 1-5/ 75. TP -7/ 37. TP -/ 3. TP -9/ 5. TP -3/ 37. TP -33/ 55. TP -3/ 5. TP -3/ 55. TP -3/ 55. TP -5/ 75. TP -57/ 9. TP -/ 9. TP -53/ 1. TP -5/ 13. Standard Design Shaft seal Pressure stage Materials Standard motor TPE Series (1 TP Series TP Series 3 TP Series BUBE AUUE RUUE BAQE BQQE GQQE DBUE PN / combination flange PN PN 1 PN 5 1 TPE pumps are not available in twin-head versions. -pole motors above kw can be operated at 3 x -9 YV. Smaller motor sizes cannot. Electronically speed controlled motor Pump housing Impeller Voltage [V] Voltage [V] Cast iron EN-GJL- Nodular cast iron EN-GJS--1 Bronze Stainless steel Cast iron Nodular cast iron EN-GJS--15 Bronze 3 x -55 ΔV/ 3 x 3- YV P 3 x -77 ΔV/ 3 x 3- YV P 3 x 3- ΔV P 3 x 3- ΔV/ 3 x -9 YV( P 3 x 3-15 V P 3 x 3- V P 13

14 Product range TP, TPD, TPE Product range, -pole, PN 5 Pump type Standard Electronically speed Design Shaft seal Pressure stage Materials Standard motor controlled motor Pump housing Impeller Voltage [V] Voltage [V] TPE Series (1 TP Series TP Series 3 TP Series BUBE AUUE RUUE BAQE BQQE GQQE DBUE PN / combination flange PN PN 1 PN 5 Cast iron EN-GJL- Nodular cast iron EN-GJS--1 Bronze Stainless steel Cast iron Nodular cast iron EN- GJS--15 Bronze TP -/ 75. TP -1/ 9. TP -1/ 1. TP -13/ 13. TP -1/ 1. TP -15/ 13. TP -17/ 1. TP -/. TP -3/. 3 x -55 ΔV/ 3 x 3- YV P 3 x -77 ΔV/ 3 x 3- YV P 3 x 3- ΔV P 3 x 3- ΔV/ 3 x -9 YV P 3 x 3-15 V P 3 x 3- V P 1

15 Product range TP, TPD, TPE Product range, -pole, PN 5 Pump type Standard Design Shaft seal Pressure stage Materials Standard motor TTPE Series (1 TP Series TP Series 3 TP Series BUBE AUUE RUUE BAQE BQQE GQQE DBUE PN / combination flange PN PN 1 PN 5 Electronically speed controlled motor Pump housing Impeller Voltage [V] Voltage [V] Cast iron EN-GJL- Nodular cast iron EN-GJS--1 Bronze Stainless steel Cast iron TP -/ 7.5 TP -/ 11. TP -33/ 15. TP -3/ 1.5 TP -/ 1.5 TP -/. TP -53/ 3. TP -59/ 37. TP 15-/ 15. TP 15-7/ 1.5 TP 15-3/. TP 15-37/ 3. TP 15-3/. TP 15-/ 3. TP 15-/ 37. TP 15-57/ 5. TP 15-/ 55. TP 1-33/ 3. TP 1-37/ 37. TP 1-/ 5. TP 1-9/ 55. TP 1-7/ 9. TP 1-/ 1. TP 1-93/ 13. TP -3/ 5. TP -37/ 55. TP -5/ 75. TP -5/ 9. TP -7/ 1. TP -7/ 13. TP -/ 1. TP -93/. TP -3/ 9. TP -/ 1. TP -5/ 13. TP -7/ 1. TP -/. TP -9/. TP -/ 315. Nodular cast iron EN- GJS--15 Bronze 3 x -55 ΔV/ 3 x 3- YV P 3 x -77 ΔV/ 3 x 3- YV P 3 x 3- ΔV P 3 x 3- ΔV/ 3 x -9 YV P 3 x 3-15 V P 3 x 3- V P 15

16 Operating conditions TP, TPD, TPE Pressure conditions System and test pressures Pressure System pressure Test pressure [bar] [MPa] [bar] [MPa] PN. 1. PN / PN PN PN Sound pressure level Max. sound pressure level [db(a)] - ISO 373 Motor Three-phase motors -pole -pole The audible noise from TP pumps is primarily noise from the motor fan. The selection of TPE pumps will reduce the noise at partial load, as the motor, and consequently, the motor fan runs at a lower speed. Possible flow noise from control valves is also reduced at partial load in the case of the TPE pump. Ambient temperature MG EFF1-motors: kw motors, -pole 1.1- kw, -pole Siemens EFF1-motors: 15-9 kw motors, -pole kw motors, -pole Other motor sizes: Storage: If the ambient temperature exceeds above maximum values or if the motor is located more than metres above sea level, the motor output () must be reduced due to the low density and consequent low cooling effect of the air. In such cases, it may be necessary to use an oversize motor with a higher rated output. Key 3 to + C 3 to +55 C 3 to + C Down to 3 C [%] t [ C] 3 7 m Fig. 1 Relationship between motor output (P ) and altitude Pos 1 Description Siemens EFF1-motors: 15-9 kw motors, -pole kw motors, -pole MG EFF1-motors: kw motors, -pole 1.1- kw, -pole 3 Other motor sizes TM

17 Pumped liquids TP, TPD, TPE, TPED Pumped liquids Thin, clean, non-aggressive and non-explosive liquids, not containing solid particles or fibres that may mechanically or chemically attack the pump, please see "List of pumped liquids" page 1. Examples of liquids: central heating system water (the water should meet the requirements of accepted standards on water quality in heating systems) cooling liquids domestic hot water industrial liquids softened water. If glycol or another antifreeze agent is added to the pumped liquid, the pump must have a shaft seal of the type RUUE or GQQE. The pumping of liquids with densities or kinematic viscosities higher than those of water can cause a considerable pressure drop a drop in the hydraulic performance a rise in the power consumption. In these situations, equip the pump with an oversize motor. If in doubt, contact Grundfos. If the water contains mineral oils or chemicals, or if other liquids than water are pumped, the O-rings should be chosen accordingly. Liquid temperature Liquid temperature: 5 C to +1 C. Please note that shaft seals operating close to their maximum temperature will require regular maintenance, i.e. replacement. Pump type Shaft seal Temperature TP Series TP Series TP Series 3 TP Series, bar version TP Series, 5 bar version BUBE BQQE GQQE C to +1 C C to +9 C 5 C to +9 C BUBE C to +1 C AUUE C to +9 C RUUE 5 C to +9 C BAQE C to +1 C (1 C) (1 BQQE GQQE BAQE BQQE GQQE C to +9 C 5 C to +9 C C to +1 C C to +9 C 5 C to +9 C DBUE C to +1 C ( 1) TP Series 3 pumps are designed for a maximum operating temperature of 1 C. For operation above 1 C, an alternative shaft seal is to be selected. Contact Grundfos. ) At +1 to +1 C, the maximum operating pressure 3 bar. Depending on the type of cast iron used and the pump application, the maximum liquid temperature may be limited by local regulations and laws. 17

18 Pumped liquids TP, TPD, TPE, TPED List of pumped liquids Grundfos TP and TPD pumps are designed for circulation systems with constant flow; TPE pumps for systems with variable flow. Thanks to their design, the pumps can be used in a wider liquid temperature range than pumps of the canned rotor type. A number of typical liquids are listed below. Other pump versions may be used, but we consider the ones stated in the list to be the best choices. The list is intended as a general guide only, and it cannot replace actual testing of the pumped liquids and pump materials under specific working conditions. If in doubt, contact Grundfos. Use the list with some caution, as factors such as concentration of the pumped liquid liquid temperature or pressure may affect the chemical resistance of a specific pump version. Legend A B C D E F G H May contain additives or impurities that may cause shaft seal problems. The density and/or viscosity differ from those of water. Consider this when calculating motor and pump performance. The liquid must be oxygen-free (anaerobic). Risk of crystallisation/precipitation in shaft seal. Insoluble in water. The shaft seal rubber parts must be replaced with FKM rubber. Bronze housing/impeller required. Risk of formation of ice on the standby pump. (The risk only applies to TP, TPE Series pumps). Pumped liquids Water Groundwater Notes Additional information Shaft seal TP Series TP Series TP Series 3 <+9 C BQQE AUUE BQQE >+9 C BUBE BUBE BAQE 1) BBQE 3) TP Series PN BAQE TP Series PN 5 Boiler-feed water <+1 C BUBE ) BUBE BAQE BAQE DBUE +1 C to +1 C BUBE BQBE 3) DBUE District heating water <+1 C BUBE BUBE BAQE BAQE DBUE Condensate Softened water Brackish water Coolants Ethylene glycol B, D, H + C, % Glycerine (glycerol) B, D, H + C, % Potassium acetate B, D, C, H + C, % Potassium formate B, D, C, H + C, % Propylene glycol C G B, D, H Brine-sodium chloride B, D, C, H +5 C, 3% Synthetic oils Silicone oil B, E <+9 C BQQE AUUE BQQE >+9 C BUBE BUBE BAQE <+9 C BQQE AUUE BQQE >+9 C BUBE BUBE BAQE ph>.5, + C, ppm Cl - BUBE BQQE BQQE GQQE BQQE GQQE BQQE GQQE BQQE GQQE BQQE GQQE BQQE GQQE BUBE BQQE BUBE AUUE AUUE RUUE AUUE RUUE AUUE RUUE AUUE RUUE AUUE RUUE AUUE RUUE BUBE AUUE BAQE BAQE DBUE DBUE DBUE BQQE BQQE DBUE BAQE ) BQQE GQQE BQQE GQQE BQQE GQQE BQQE GQQE BAQE ) BQQE GQQE BQQE GQQE BAQE BQQE GQQE DQQE 3) GQQE DQQE 3) GQQE DQQE 3) GQQE DQQE 3) GQQE DQQE 3) GQQE DQQE 3) BAQE DBUE (To be continued) 1

19 Pumped liquids TP, TPD, TPE, TPED Pumped liquids Vegetable oils Corn oil (1 BAQE must not be used for potable water. For potable water, Grundfos recommends a BBQE shaft seal. ( BAQE can be used in air-condition applications at temperatures above C. (3 The shaft seal is not standard, but available on request. ( Maximum +1 C. B, F, E Olive oil B, F, E <+ C Peanut oil Rape seed oil Soya bean oil Cleaning agents B, F, E D, B, F, E B, F, E Soap (salts of fatty acids) A, E, (F) <+ C Alkaline degreasing agent A, E, (F) <+ C Oxidants Notes Additional information Hydrogen peroxide <+ C, <% BUBV 3) BUBV 3) BAQV 3) BQQV 3) AUUV 3) BQQV 3) BAQV 3) DBUV 3) BUBV 3) BUBV 3) BAQV 3) BQQV 3) AUUV 3) BQQV 3) BAQV 3) DBUV 3) BUBV 3) BUBV 3) BAQV 3) BQQV 3) AUUV 3) BQQV 3) BAQV 3) DBUV 3) BUBV 3) BUBV 3) BAQV 3) BQQV 3) AUUV 3) BQQV 3) BAQV 3) DBUV 3) BUBV 3) BUBV 3) BAQV 3) BQQV 3) AUUV 3) BQQV 3) BAQV 3) DBUV 3) BQQE (BQQV) 3) BQQE (BQQV) 3) BUBE BQQE AUUE (AUUV) 3) AUUE (AUUV) 3) BUBE AUUE Shaft seal TP Series TP Series TP Series 3 TP Series PN TP Series PN 5 BQQE (BQQV) 3) GQQE DQQE 3) BQQE (BQQV) 3) GQQE DQQE 3) BQQE BQQV 3) DQQE 3) Salts Ammonium bicarbonate A <+ C, <15% BQQE AUUE BQQE GQQE DQQE 3) Calcium acetate A, B <+ C, <3% BQQE AUUE BQQE GQQE DQQE 3) Potassium bicarbonate A <+ C, <% BQQE AUUE BQQE GQQE DQQE 3) Potassium carbonate A <+ C, <% BQQE AUUE BQQE GQQE DQQE 3) Potassium permanganate A <+ C, <% BQQE AUUE BQQE GQQE DQQE 3) Potassium sulphate A <+ C, <% BQQE AUUE BQQE GQQE DQQE 3) Sodium acetate A <+ C, <% BQQE AUUE BQQE GQQE DQQE 3) Sodium bicarbonate A <+ C, <% BQQE AUUE BQQE GQQE DQQE 3) Sodium carbonate A <+ C, <% BQQE AUUE BQQE GQQE DQQE 3) Sodium nitrate A <+ C, <% BQQE AUUE BQQE GQQE DQQE 3) Sodium nitrite A <+ C, <% BQQE AUUE BQQE GQQE DQQE 3) Sodium phosphate (di) A <+ C, <3% BQQE AUUE BQQE GQQE DQQE 3) Sodium phosphate (tri) A <+9 C, <% BQQE AUUE BQQE GQQE DQQE 3) Sodium sulphate A <+ C, <% BQQE AUUE BQQE GQQE DQQE 3) Sodium sulphite A <+ C, <1% BQQE AUUE BQQE GQQE DQQE 3) Alkalis Ammonium hydroxide <+ C, <3% BQQE AUUE BQQE GQQE DQQE 3) Calcium hydroxide A <+ C, <% BQQE AUUE BQQE GQQE DQQE 3) Potassium hydroxide A <+ C, <% BQQE AUUE BQQE GQQE DQQE 3) Sodium hydroxide A <+ C, <% BQQE AUUE BQQE GQQE DQQE 3) 19

20 TP Series pumps TP, TPD, TPE Materials TP, TPE Series 5 3 Fig. TP Series Technical data Flow rate: up to 9 m 3 /h Head: up to 7 m Liquid temperature: 5 to +1 C Max. operating pressure: up to 1 bar Direction of rotation: Construction Counter-clockwise Grundfos TP Series pumps are single-stage, closecoupled pumps with inline suction and discharge ports of identical diameter. The pumps are equipped with a fan-cooled asynchronous motor. Motor and pump shafts are connected via a rigid two-part coupling. TP Series pumps are available as single-head (TP) and twin-head (TPD) models. TP Series pumps have flange connection and are equipped with PN or PN flanges. The pumps are equipped with an unbalanced mechanical shaft seal. The pumps are of the top-pull-out design, i.e. the power head (motor, pump head and impeller) can be removed for maintenance or service while the pump housing remains in the pipework. The twin-head pumps are designed with two parallel power heads. A non-return flap valve in the common discharge port is opened by the flow of the pumped liquid and prevents backflow of liquid into the idle pump head. As radial and axial forces are absorbed by the fixed bearing in the motor drive-end, the pump requires no bearing. TP and TPD Series pumps are equipped with highefficiency motors. Pumps with bronze pump housing (version B) are suitable circulation of domestic hot water. GR1 Fig. 3 Sectional drawing of a TPE Series (flanged model) Material specification Series Pos. Component Material EN/DIN 1 Pump housing Cast iron EN-GJL-, bronze CuSn..93 Impeller Stainless steel Shaft Stainless steel 1.35 Coupling Cast iron EN-GJL-.7 5 Pump head Secondary seals Rotating seal face Stationary seat Cast iron EN-GJL-, bronze EPDM Tungsten carbide 1 Carbon (synthetic resinimpregnated) silicon carbide.5.93 TM

21 TP Series pumps TP, TPD, TPE Mechanical shaft seal Three types of unbalanced mechanical shaft seals are available as standard: BUBE The BUBE shaft seal is a Grundfos rubber bellows seal with tungsten carbide/carbon seal faces and secondary seals of EPDM. RUUE/GQQE The RUUE shaft seal is a Grundfos O-ring seal with reduced tungsten carbide/tungsten carbide seal faces and secondary seals of EPDM. The GQQE shaft seal is a Grundfos rubber bellows seal with reduced seal faces and silicon carbide/ silicon carbide seal faces and secondary seals of EPDM. AUUE/BQQE The AUUE shaft seal is a Grundfos O-ring seal with fixed seal driver, tungsten carbide/tungsten carbide seal faces and secondary seals of EPDM. The BQQE shaft seal is a Grundfos rubber bellows seal with silicon carbide/silicon carbide seal faces and secondary seals of EPDM. Information on a selection of common pumped liquids with recommended shaft seals is shown on page 1. Shaft seal specification Unbalanced shaft seal Shaft diameter Rubber bellows Seal faces TP, TPD Series version NU according to EN and 1 mm EPDM Tungsten carbide/carbon Tungsten carbide/ tungsten carbide Silicon carbide/ silicon carbide Special shaft seals are available for partly conditioned water or other liquids containing abrasive or crystallising particles. See page 1. Features and benefits TP Series pumps have the following product features and benefits: Optimised hydraulics for high efficiency - reduced power consumption. High-efficiency motors - TP pumps are fitted with high-efficiency motors. High-efficiency motors offer reduced energy consumption. -pole and -pole TP pumps from 1.1 kw and above have EFF1 motors fitted. Top-pull-out design - easy dismantling in case of service. In-line design - contrary to end-suction pumps, in-line pumps allow a straight pipework and thus often reduced installation costs. Pump housing and pump head are electrocoated to improve the corrosion resistance - Electrocoating includes: 1. Alkaline cleaning. Pre-treatment with zinc phosphate coating 3. Cathodic electrocoating (epoxy). Curing of paint film at - C. For low-temperature applications at a high humidity, Grundfos offers TP pumps with extra surface treatment to avoid corrosion. These pumps are available on request. Stainless steel impeller and neck ring - wear-free operation with high efficiency. Connections TP Series pumps up to DN 5 are equipped with combination flanges PN /PN. DN or DN pumps have either PN or PN flanges. All flanges can be connected to flanges in accordance with EN 9- and ISO

22 TP Series 3 pumps TP, TPD, TPE TP, TPD, TPE Series 3 pumps are equipped with high-efficiency motors. TP Series 3 pumps with bronze impeller are suitable for pumping brine. Materials Fig. TP Series 3 Technical data Flow rate: up to m 3 /h Head: up to 93 m Liquid temperature: 5 to +1 C Max. operating pressure: 1 bar GR Fig. 5 Sectional drawing of TP Series 3 Material specification TM Direction of rotation: Construction Clockwise Grundfos TP, TPD Series 3 pumps are single-stage, close-coupled pumps with in-line suction and discharge ports of identical diameter. The pumps are equipped with a fan-cooled asynchronous motor. Motor and pump shafts are connected via a rigid sleeve coupling. Most TP Series 3 pumps are available as singlehead (TP) and twin-head (TPD) models. TP Series 3 pumps have flange connection and are equipped with PN 1 flanges. The pumps are equipped with an unbalanced mechanical shaft seal. The pumps are of the top-pull-out design, i.e. the power head (motor, pump head and/or motor stool and impeller) can be removed for maintenance or service while the pump housing remains in the pipework. The twin-head pumps are designed with two parallel power heads. A non-return flap valve in the common discharge port is opened by the flow of the pumped liquid and prevents backflow of liquid into the idle pump head. As radial and axial forces are absorbed by the fixed bearing in the motor drive-end, the pump requires no bearing. The impeller is hydraulically balanced to minimize axial forces. Pos. Component Material EN/DIN 1 Pump housing Cast iron EN-GJL- EN-JL Impeller 3 Shaft/sleeve coupling Pump head/ motor stool Secondary seals Rotating seal face Stationary seat Cast iron EN-GJL-, bronze CuSn5Zn5Pb Steel/stainless steel Mechanical shaft seal EN-JL Cast iron EN-GJL- EN-JL EPDM Metal-impregnated carbon, silicon carbide Silicon carbide Three types of unbalanced mechanical shaft seal are available as standard: BAQE The BAQE shaft seal is a Grundfos rubber bellows seal with carbon/silicon carbide seal faces and secondary seals of EPDM. GQQE The GQQE shaft seal is a Grundfos rubber bellows seal with reduced silicon carbide/silicon carbide seal faces and secondary seals of EPDM. BQQE The BQQE shaft seal is a Grundfos rubber bellows seal with silicon carbide/silicon carbide seal faces and secondary seals of EPDM. Information on a selection of common pumped liquids with recommended shaft seals is shown on page 1.

23 TP Series 3 pumps TP, TPD, TPE Shaft seal specification Unbalanced shaft seal version NU according to EN 175 Shaft diameter, 3, and 55 mm Rubber bellows EPDM Seal faces Special shaft seals are available for partly conditioned water or other liquids containing abrasive or crystallising particles. See page 1. Connections Carbon/silicon carbide Silicon carbide/silicon carbide TP, TPD Series 3 pumps are equipped with PN 1 flanges. All dimensions are according to ISO 75- or EN 9-. Features and benefits TP Series 3 pumps have the following features and benefits: Optimised hydraulics for high efficiency - reduced power consumption. High-efficiency motors - TP pumps are fitted with high-efficiency motors. High-efficiency motors offer reduced energy consumption. -pole and -pole TP pumps from 1.1 kw to 9 kw have EFF1 motors fitted. Top-pull-out design - easy dismantling in case of service. In-line design - contrary to end-suction pumps, in-line pumps allow a straight pipework and thus often reduced installation costs. Motor-pump shaft with sleeve coupling - - Stable and quiet operation. Easy dismantling in case of service. Hydraulically and mechanically balanced impeller - The impeller is hydraulically and mechanically balanced to increase the life of motor bearings and shaft seal. Pump housing and motor stool are electrocoated to improve the corrosion resistance - Electrocoating includes: 1. Alkaline cleaning. Pre-treatment with zinc phosphate coating 3. Cathodic electrocoating (epoxy). Curing of paint film at - C. For low-temperature applications at a high humidity, Grundfos offers TP pumps with extra surface treatment to avoid corrosion. These pumps are available on request. TPE - pumps with built-in frequency converter - -pole and -pole TP pumps from 1.1 to kw are available as TPE pumps with built-in frequency converter. For further information, see page. 3

24 TP Series pumps TP, TPD, TPE Materials GR7539 Fig. 7 Sectional drawing of TP Series TM 9 Fig. TP Series Technical data Flow rate: Head: Liquid temperature: Construction PN version: PN 5 version: PN version: PN 5 version: PN version: up to 13 m 3 /h up to m 3 /h up to 55 m up to 17 m 5 to +1 C PN 5 version: to +1 C From +1 to +1 C, max. 3 bar Max. operating pressure: bar version: bar 5 bar version: 5 bar Direction of rotation: Clockwise Grundfos TP Series pumps are single-stage, closecoupled pumps with in-line suction and discharge ports. The pumps are equipped with a fan-cooled asynchronous motor. Motor and pump shafts are connected via a rigid flange coupling. Material specification TP Series, PN Pos. Component Material EN/DIN 1 Pump housing Cast iron EN-GJL- EN-JL Impeller Ductile cast iron EN-GJS- EN-JL3 Bronze Pump shaft Stainless steel 1.3 Coupling Cast iron EN-GJL- EN-JL 5 Motor stool Cast iron EN-GJL- EN-JL Secondary seals EPDM rubber Rotating seal face Stationary seat TP Series, PN 5 Carbon, metal-impregnated Silicon carbide Silicon carbide Pos. Component Material EN/DIN 1 Pump housing Ductile cast iron EN-GJS--1 (A-LT) EN-JS Impeller Ductile cast iron EN-GJS- EN-JS3 Bronze Pump shaft Stainless steel 1.3 Coupling Cast iron EN-GJL- EN-JL 5 Motor stool Cast iron EN-GJL- EN-JL Secondary seals EPDM rubber Rotating seal face Stationary seat Carbon, synthetic resin-impregated Tungsten carbide TP Series pumps are available as single-head (TP) models. All TP Series pumps have flange connection PN or PN 5. The largest pumps have DN, PN discharge flanges and a maximum operating pressure of 5 bar. The pumps are equipped with an unbalanced mechanical shaft seal. The pumps are of the top-pull-out design, i.e. the power head (motor, motor stool, pump head and impeller) can be removed for maintenance or service while the pump housing remains in the pipework. As radial and axial forces are absorbed by the fixed bearing in the motor drive-end, the pump requires no bearing. TP Series pumps are equipped with high-efficiency motors.

25 TP Series pumps TP, TPD, TPE Mechanical shaft seal For bar versions, the following three types of unbalanced mechanical shaft seals are available as standard: BAQE The BAQE shaft seal is a Grundfos rubber bellows seal with carbon/silicon carbide seal faces and secondary seals of EPDM. GQQE The GQQE shaft seal is a Grundfos rubber bellows seal with reduced silicon carbide/silicon carbide seal faces and secondary seals of EPDM. BQQE The BQQE shaft seal is a Grundfos rubber bellows seal with silicon carbide/silicon carbide seal faces and secondary seals of EPDM. For 5 bar versions, the following mechanical shaft seal is available as standard: DBUE The DBUE shaft seal is a Grundfos balanced O-ring seal with carbon/tungsten carbide seal faces and secondary seals of EPDM. Information on a selection of common pumped liquids with recommended shaft seals is shown on page 1. Special shaft seals are available for partly conditioned water or other liquids containing abrasive or crystallising particles. See page 1. Connections TP Series pumps are the only TP pumps with suction and discharge ports of different diameters. The suction port is one dimension larger than the discharge port in order to obtain a low inlet velocity. This reduces risk of cavitation and noise. From DN to DN 3 TP Series pumps have flanges according to ISO 75- or EN 9-. Features and benefits TP Series pumps have the following features and benefits: Optimised hydraulics for high efficiency - reduced power consumption. High-efficiency motors - TP pumps are fitted with high-efficiency motors. High-efficiency motors offer reduced energy consumption. -pole and -pole pumps from kw to 9 kw have EFF1 motors fitted. Top-pull-out design - easy dismantling in case of service. In-line design - contrary to end-suction pumps, in-line pumps allow a straight pipework and thus often reduced installation costs. Motor-pump shaft with flanged coupling - - stable and quiet operation easy dismantling in case of service. Supported flange connection - The pump housing have flange connections with integrated feet in order to stabilize the pump. Surface treatment TP Series pumps are given the following surface treatment: Pump type Electrocoating Spray painting TP Series (from DN to DN 3) x x TP Series (DN ) x Electrocoating includes: 1. Alkaline cleaning. Pre-treatment with zinc phosphate coating 3. Cathodic electrocoating (epoxy). Curing of paint film at - C. For low-temperature applications at a high humidity, Grundfos offers TP pumps with extra surface treatment to avoid corrosion. These pumps are available on request. 5

26 TPE Series pumps TP, TPD, TPE Fig. TPE Series Technical data Flow rate: up to 3m 3 /h Head: up to 9 m Liquid temperature: 5 up to +1 C Max. operating pressure: 1 bar Motor sizes (three-phase): 1.1 to kw Construction TPE Series pumps are based on TP Series and 3 pumps. The main difference between the TP and the TPE Series pump range is the motor. The motor of TPE Series pumps a has built-in frequency converter for continuous adjustment of the pressure to the flow rate. TPE Series pumps are suitable for applications where the pressure, temperature, flow rate or another parameter is to be controlled on the basis of signals from a sensor at some point in the system. Note: TPE Series pumps are not fitted with a sensor from factory. For further information on construction and materials of TPE Series pumps, see page to 3. TM3 3 5 Applications TPE Series pumps have integrated speed control for automatic adaptation of performance to current conditions. This ensures that the energy consumption is kept at a minimum. TPE pumps can operate in any duty point in the range between 5% and % speed. H 5% % Q [m³/h] Fig. 9 Duty range of TPE Series pumps In the QH-chart the %-curve corresponds to the curve for a pump fitted with a standard fixed speed motor. Depending on the nature of the application, TPE Series pumps offer energy-savings, increased comfort or improved processing. The pumps can be fitted with sensor types meeting the requirements mentioned in the data booklet titled Grundfos E-pumps. TM

27 TPE Series pumps TP, TPD, TPE The charts below show possible control modes of TPE Series pumps in different applications. Control mode Constant curve Application Single-pipe heating system Systems with three-way valves Heating and cooling surfaces Chiller pumps Constant differential pressure Systems with two-way valves (Sensor is needed) Control options Communication with TPE Series pumps is possible via a central building management system remote control (Grundfos R) or a control panel. The purpose of controlling a TPE Series pump is to monitor and control the pressure, temperature, flow and liquid level of the system. For further information about control options of TPE pumps, see page. Temperature control Constant flow Single-pipe heating system Systems with three-way valves Cooling towers Chiller pumps Domestic hot water recirculation (Sensor is needed) Heating and cooling surfaces Cooling towers Flow filters (Sensor is needed) Proportional differential pressure (measured) System with two-way valves (Differential pressure sensor is located in the system) 7

28 Communication TP, TPD, TPE Communication with TPE pumps Communication with TPE pumps is possible via a central building management system, remote control (Grundfos R) or control panel. Central building management system The operator can communicate with a TPE pump at a distance. Communication can take place via a central building management system allowing the operator to monitor and change control modes and setpoint settings. Remote control The R remote control produced by Grundfos is available as an accessory. The operator can communicate with the TPE pump by pointing the IR-signal transmitter at the control panel of the terminal box. TM3 11 LON-bus connection Fig. 11 R remote control The operator can monitor and change control modes and settings of the TPE pump via the R display. Control panel The operator can change the setpoint settings manually on the control panel of the TPE pump terminal box. G-LON Inteface GENIbus connection TPE pump TM Fig. 1 Control panel of a TPE pump TM 7 Fig. Structure of a central building management system

29 Speed regulation of TPE pumps TP, TPD, TPE Affinity equations Normally, TPE pumps are used in applications characterised by a variable flow. Consequently, it is not possible to select a pump that is constantly operating at its optimum efficiency. H H n Q n n n = Q x n x In order to achieve optimum operating economy, the pump should be selected at the flow rate at the duty point close to the optimum efficiency (eta) for most operating hours. Between the min. and max. performance curves, TPE pumps have an infinite number of performance curves each representing a specific speed. It may therefore not be possible to select a duty point close to the max. curve. H x Eta Q x n n n x Q n n x n n Q H n n n = H x n x η n η x H Max. curve P n P Q x Q n n n Q P n n n = P n x x Min. curve Q [m³/h] Fig. 13 Min. and max. performance curves In situations where it is not possible to select a duty point close to the max. curve, use the affinity equations below. The head (H), the flow rate (Q) and the input power (P) are the appropriate variables you need for calculating the motor speed (n). Note: The approximated formulas apply on condition that the system characteristic remains unchanged for n n and n x, and that it is based on the formula H = k x Q where k is a constant. The power equation implies that the pump efficiency is unchanged at the two speeds. In practice this is not quite correct. Finally, it is worth noting that the efficiency of the frequency converter and the motor must be taken into account if a precise calculation of the power saving resulting from a reduction of the pump speed is wanted. TM Px Fig. 1 Affinity equations Legend H n Rated head in metres H x Current head in metres Q n Rated flow rate in m 3 /h Q x Current flow rate in m 3 /h n n Rated motor speed in min -1 n x Current motor speed in min -1 η n Rated efficiency in % η x Current efficiency in % WinCAPS and WebCAPS WinCAPS and WebCAPS are selection programs offered by Grundfos. n x The two programs make it possible to calculate the specific duty point and energy consumption of a TPE pump. When you enter the dimensions of the pump, WinCAPS and WebCAPS can calculate the exact duty point and energy consumption. For further information, see page 11. Q TM

30 Motor data TP, TPD, TPE Motor The motor fitted on TP pumps is a totally enclosed, fancooled standard motor with main dimensions to IEC and DIN standards. Electrical tolerances to IEC 3. Mounting designation Pump type Mounting designation - IEC 3-7 TP Series TP Series IM 31 (IM B 1) /IM 311 (IM V 1) TP Series 3 IM 31 (IM B 1) /IM 311 (IM V 1) IM 31 (IM B 5) /IM 311 (IM V 1) TP Series IM 31 (IM B 5) /IM 311 (IM V 1) Relative humidity: Max. 95% Enclosure class: IP 55 Insulation class: F, to IEC 5 Ambient temperature: Max. +55 C (EFF1 motors) Max. + C (other motor sizes) Min. 3 C. If the pump is installed in humid locations, open the lowest drain hole in the motor. This will reduce the motor enclosure class to IP. Motor range kw Electronic speed controlled Standard motors motors -pole -pole -pole -pole MG MG MGE MGE 15. MMGE MMGE Siemens Siemens MG and MGE are Grundfos motor brands. Siemens and MMGE are sourced high-quality motor brands. The grey-shaded areas indicate non-available motors. High-efficiency motors TP pumps are fitted with high-efficiency motors. TP, TPD pumps with - and -pole three-phase motors from 1.1 to 9 kw are equipped with EFF1 motors. TPE pumps with three-phase motors, -pole from 1.1 to 7.5 kw and -pole from 1.1 to. kw, are equipped with motors equivalent to EFF1. EFF1 is the highest efficiency class defined by CEMEP (European Committee of Manufactures of Electrica Machines and Power Electronics). Motor protection MG/Siemens Three-phase motors must be connected to a motor starter. All three-phase standard motors can be connected to an external frequency converter. If you connect a frequency converter the motor insulation system will often be overloaded, and the motor will be more noisy than in normal operation. In addition, large motors will be exposed to bearing currents caused by the frequency converter. If you operate the motor via a frequency converter, considered the following: In -, - and -pole motors of 75 kw (frame size ) and upwards, isolate one of the motor bearings electrically to prevent damaging currents from passing through the motor bearings. If you have noise-sensitive applications, you can reduce the motor noise by fitting a du/dt filter between the motor and the frequency converter. In particularly noise-sensitive applications, we recommend you to fit a sinusoidal filter. The length of the cable between motor and frequency converter affects the motor load. Therefore, check that the cable length meets the specifications laid down by the frequency converter supplier. For supply voltages between and 9 V, fit either a du/dt filter to reduce voltage peaks or use a motor with reinforced insulation. For supply voltages of 9 V, use a motor with reinforced insulation and fit a du/dt filter. MGE/MMGE MGE, MMGE motors with built-in frequency converter do not require protection by a motor-protective circuit breaker. 3

31 Motor data TP, TPD, TPE Electrical data, standard motors Electrical data, -pole 3 x -55/3- V Electrical data, -pole Motor Electrical data, -pole Electrical data, -pole 3 x -55/3- V I 1/1 [A] Cos ϕ 1/1 η [%] n [min -1 ] / / / Motor x -77/3- V I 1/1 [A] Cos ϕ 1/1 η[%] n [min -1 ] / / / / / / / / / / / / / / Motor 3 x 3-/-9 V I 1/1 [A] Cos ϕ 1/1 η [%] n [min -1 ] I Start I 1/1 I Start I 1/1 I Start I 1/ / / / / / / / / / / / / / / Motor Electrical data, -pole Electrical data, -pole I 1/1 [A] Cos ϕ 1/1 η [%] n [min -1 ] / / / / Motor 3 x -77/3- V I 1/1 [A] Cos ϕ 1/1 η [%] n [min -1 ] / / / / / / / / / / / Motor 3 x 3-/-9 V I 1/1 [A] Cos ϕ 1/1 η [%] n [min -1 ] I Start I 1/1 I Start I 1/1 I Start I 1/ / / / / / / / / / / / / / / / / / / /

32 Motor data TP, TPD, TPE Electrical data, motors with built-in frequency converter Electrical data, -pole 3x3- V, 9 min -1 Motor I 1/1 [A] Electrical data, -pole 3x3-15 V, 9 min -1 Motor I 1/1 [A] Electrical data, -pole 3x3- V, 1 min -1 Motor I 1/1 [A] Electrical data, -pole 3x3-15 V, 1 min -1 Motor I 1/1 [A]

33 Installation TP, TPD, TPE Mechanical installation TP, TPD, TPE pumps up to 11 kw can be installed in horizontal and vertical pipes. Twin-head pump housings have two Rp 1/ tappings (TP Series ) or four Rp 1/ tappings (TP Series 3) for mounting of automatic air vents. Fig. 15 Installation of motor sizes up to 11 kw TP, TPD, TPE pumps from 11 kw and upwards can only be installed in horizontal pipes. Fig. 1 Installation of motor sizes from 11 kw and upwards Note: The motor must never point downwards. Install the pumps in such a way that strain from the pipework is not transferred to the pump housing. Pumps with motors up to 11 kw may be suspended direct in the pipes, provided the pipework can support the pump. If not, install the pump on a mounting bracket or base plate. Pumps with motors larger than 11 kw can only be installed in horizontal pipes with the motor placed in vertical position. Always install the pump on an even and rigid foundation. When installing a twin-head pump in a horizontal pipe and with horizontal shaft, fit the upper pump housing with an automatic air vent. TM TM Fig. 17 Tappings for mounting of automatic air vents in TP Series and TP Series 3 For further information about identification of TP Series and TP Series 3 models, see page to. Cooling To ensure sufficient cooling of motor and electronics, observe the following: Place the pump in such a way that sufficient cooling is ensured. Make sure that the temperature of the cooling air does not exceed + C. Keep the motor cooling fins, holes in fan cover and fan blades clean. Make sure the frequency for the motor is at least Hz (1% of maximum speed). TM

34 Installation TP, TPD, TPE Condensation cover for TPE pumps When installing TPE pumps outdoors, provide the motor with a suitable cover to avoid condensation on the electronic components and to protect the pump and motor against the direct effects of the elements. When mounting the condensation cover on top of the motor, make sure to leave enough space for the air to cool the motor. Fig. 1 MGE and MMGE motors with condensation cover Elimination of noise and vibrations In order to achieve optimum operation and minimum noise and vibration, consider vibration dampening of the pump. Generally, always consider this for pumps with motors above 11 kw. Smaller motor sizes, however, may also cause undesirable noise and vibration. Noise and vibration are generated by the revolutions of the motor and pump and by the flow in pipes and fittings. The effect on the environment is subjective and depends on correct installation and the state of the remaining system. Elimination of noise and vibrations is best achieved by means of a concrete foundation, vibration dampers and expansion joints. Concrete foundation Expansion joint TM3 37 Vibration dampers To prevent the transmission of vibrations to buildings, we recommend you to isolate the pump foundation from building parts by means of vibration dampers. The selection of the right vibration damper requires the following data: forces transmitted through the damper motor speed considering speed control, if any required dampening in % (suggested value is 7%). Which is the right damper varies from installation to installation, and a wrong damper may increase the vibration level. Vibration dampers should therefore be sized by the supplier. If you install the pump on a foundation with vibration dampers, always fit expansion joints on the pump flanges. This is important to prevent the pump from "hanging" in the flanges. Expansion joints Install expansion joints to absorb expansions/contractions in the pipework caused by changing liquid temperature reduce mechanical strains in connection with pressure surges in the pipework isolate mechanical structure-borne noise in the pipework (only rubber bellows expansion joints). Note: Do not install expansion joints to compensate for inaccuracies in the pipework such as centre displacement of flanges. Fit expansion joints at a distance of minimum 1 to 1½ times the nominal flange diameter away from the pump on the suction as well as on the discharge side. This will prevent the development of turbulence in the expansion joints, resulting in better suction conditions and a minimum pressure loss on the pressure side. At high water velocities (> 5 m/s) we recommend you to install larger expansion joints corresponding to the pipework. The illustration below shows examples of rubber bellows expansion joints with or without limit rods. Vibration dampers Fig. 19 Foundation of TP pump Concrete foundation Install the pump on a plane and rigid concrete foundation. This is the optimum solution for vibration dampening. As a rule of thumb, the weight of a concrete foundation should be 1.5 times the pump weight. TM 993 Fig. Examples of rubber bellows expansion joints TM TM

35 Installation TP, TPD, TPE Expansion joints with limit rods can be used to reduce the effects of the expansion/contraction forces on the pipework. We always recommend expansion joints with limit rods for flanges larger than DN. Anchor the pipes in such a way that they do not stress the expansion joints and the pump. Follow the supplier s instructions and pass them on to advisers or pipe installers. The illustration below shows an example of a metal bellows expansion joint with limit rods. TM 9 19 Fig. 1 Example of metal expansion joint Due to the risk of rupture of the rubber bellows, metal bellows expansion joints may be preferred at temperatures above + C combined with high pressure. Terminal box positions TP single-head pumps As standard, the terminal boxes of TP and TPE pumps are mounted in position 9 o clock. The possible terminal box positions are shown below. Position Stellung 3 3o clock Position o clock Position 9 o clock Standard Position 1 o clock Stellung Stellung 9 Stellung 1 TM Fig. Possible terminal box positions Note: Due to the motor construction the terminal boxes of some TP pumps with motor sizes above kw are mounted in position.3. TPD twin-head pumps As standard, the terminal boxes of all TPD pumps are mounted in position 1 o clock, see above. 35

36 Installation TP, TPD, TPE Electrical installation Electrical connection Carry out electrical connection and protection in accordance with local regulations. The pump must be connected to an external mains switch with a minimum contact gap of 3 mm in all poles. Electronically speed-controlled pumps must always be correctly earthed. Note: The. - kw motors must be connected to especially reliable/sturdy earth connections to avoid earth leakage currents above 3.5 ma. Three-phase standard motors must be connected to a motor-protective circuit breaker. Motors as from 3 kw incorporate thermistors (PTC). The thermistors are designed according to DIN. When the pump is switched on via the mains, the pump will start after approx. 5 seconds. Note: Carry out the mains connection of the pump as shown in the diagram inside the terminal box cover. Do not start the pump until it has been filled with liquid and vented. Protection Protection against fault currents If the pump is connected to an electric installation where an earth leakage circuit breaker (ELCB) is used as additional protection, the earth leakage circuit breaker must be marked with the following symbols. Three-phase: The earth leakage circuit breaker must trip out when earth fault currents with DC content (pulsating DC) and smooth DC earth fault currents occur. Protection against voltage peaks If you use speed controllers or frequency converters of other makes than Grundfos, you may have the following problems: increased motor noise detrimental voltage peaks additional motor losses. Pumps with voltage peaks exceeding V (maximum value) must therefore be protected. The voltage increase rate du/dt must not exceed Vμs. Noise and detrimental voltage peaks can be prevented by fitting an LC filter between the speed controller and the motor. Communication cables for TPE Use screened cables (min..5 mm ) for external on/off switch, digital input, sensor and setpoint signals. The screens of the cables should be connected to frame at both ends. The screen of the cable must have good frame connection which must be as close as possible to the terminals. Screen Fig. 3 External start/stop cable connection of TPE Use a screened -core cable for the bus connection. Connect the screen to terminal Y at both ends. Screen Y TM TM Fig. Bus connection of TPE 3

37 Installation TP, TPD, TPE Other connections, TPE See the wiring diagrams for instructions on how to connect external potential-free contacts for start/stop and digital function, external setpoint signal and fault signal. Wiring diagram, three-phase, 11 - kw, -pole and kw, -pole Connect the wires to the following terminal groups: Group 1: Group : Inputs (external start/stop, digital function, setpoint and sensor signals, terminals 1-9 and bus connection, A, Y, B). All inputs are separated from the mains conducting parts by reinforced insulation. Output (signal relay). The output, terminals C, NO and NC, are galvanically separated from other circuits. Therefore, the supply voltage or protective extra-low voltage can be connected to the output as desired. : + V 7: Sensor input : GND (frame) 5: +5 V : Setpoint input 3: GND (frame) : Start/stop 1: Digital input A: RS-5A Y: Screen B: RS-5B Group 1 Group Group 3 Group 3: Mains supply. Note: As a precaution, separate the wires from each other by reinforced insulation in their entire lengths. If no external on/off switch is connected, maintain the connection across terminals and 3. Wiring diagram, three-phase, kw, -pole and kw, -pole Fig. Wiring diagram, three-phase TPE pumps TM NC C NO Group L1 L L3 Group 3 - V /- ma - ma 1/ B Y A Group 1 STOP RUN /- ma - V K 5 3 TM 1 53 Fig. 5 Wiring diagram, three-phase TPE pumps 37

38 Flanges for TP pumps TP, TPD, TPE Flange dimensions PN and PN flanges D 1 D D 3 S TM EN 9- PN (. MPa) EN 9- PN (1. MPa) Nominal diameter (DN) Nominal diameter (DN) D D D S x1 x1 x1 x1 x19 x19 x19 x19 x19 x19 x19 x19 x19 x3 x3 1x3 PN 1 and PN 5 flanges D 1 D D 3 S TM EN 9- PN 1 (1. MPa) EN 9- PN 5 (.5 MPa) Nominal diameter (DN) Nominal diameter (DN) D D D S x19 x19 x19 x19 x19 x19 x19 x3 1x3 x19 x19 x3 x x 1x 1x31 1x31 PN flanges D 1 D D 3 S TM EN/DIN 35 PN (. MPa) Nominal diameter (DN) D 1 D D 3 S 1x x 3

39 Curve charts TP, TPD, TPE How to read the curve charts H 1 -/ TP, TPE Hz Pump type and frequency 9 7 -/ -79/ -7/ -5/ QH curve for the individual single-head pump. The bold curve indicates the recommended performance range. -/ Q [m³/h] -7/ -5/ -/ -/ -79/ -/ 3 7 Q [m³/h] NPSH Q [m³/h] Eta [%] / -/ -5/ -/ -79/ -/ 3 7 Q [m³/h] The power curve indicates pump input power [P ]. The NPSH(3%) curve shows the required net positive suction head (NPSH) to ensure that the pump head is not reduced by more than 3%. The available system pressure at the pump inlet must be according to the NPSH(3%) curve + a safety margin of at least.5 m. The eta curve shows the pump efficiency Q [l/s] v [m/s] TM 39 39

40 Curve charts TP, TPD, TPE Curve conditions The guidelines below apply to the curves shown on the following pages: 1. Tolerances to ISO 99, Annex A.. The curves apply to the performance of singlehead three-phase pumps. For other pump versions, please see the exact curves in WinCAPS or WebCAPS. For other pump versions, the performance may differ for the following reasons: - The valve in twin-head pumps may cause losses. Note: Grundfos does not recommend continuous parallel operation of twin-head pumps due to the increased flow in the pump. A too high flow results in noisy operation, increased wear of the impeller due to cavitation, etc. 3. QH curves of the individual single-head pumps are shown with expected speed of a three-phase standard motor. For further information, see the tables of technical data on the following pages.. Curves of TPE Series pumps are shown as max. curves (% curves) only. Please refer to WinCAPS for the exact curves. 5. Measurements have been made with airless water at a temperature of + C.. The curves apply to a kinematic viscosity of υ =1mm /s (1 cst). 7. Due to the risk overheating, the pump must not run constantly below the minimum flow rate indicated by the bold curves.. If the pumped liquid density and/or viscosity are higher than those of water, it may be necessary to use a motor with a higher performance.

41 1

42 Performance curves/ Technical data DN 3 -pole, PN //1 TP, TPD, TPE -pole, PN //1 TP, TPD, TPE 3-XX/ H 3-33/ TP 3 Hz H 9 -/ TP, TPE 3 Hz -/ 7 -/ -/ -5/ 1-1/ -/ 1-3/ -/ 3-3/ Q [m³/h] -33/ -/ -/ -1/ -/ 1 1 Q [m³/h] NPSH -1/ -/, -/, -33/ Eta [%] 7 3 -/ 1 1 Q [m³/h] -/ -/ -/ -33/ -1/ Q [m³/h] -/ -3/ -3/ -5/ -/ -/ Q [m³/h] NPSH 1 1 Eta [%] Q [m³/h] -5/ -/ -/ -/ -3/ -3/ 1 1 Q [m³/h] 1 3 Q [l/s] 1 3 v [m/s] Note: All QH-curves apply to single-head pumps. For further information, see page. TM Q [m³/h] Q [l/s] v [m/s] TM 35

43 Technical data DN 3 -pole, PN //1 P B3 P Rp 1/ H AF AE D1 B1 B M L1 C5 H H1 H C1 B1 D1 B AE AF AE AF M M L1 C C5 H H1 C1 TM 3 - TM 31 Technical data TP 3 -/ -1/ -/ -/ -33/ -3/ -3/ -/ -5/ -/ -/ TPD TPE TPED Series phase TP IEC size 3-phase TP phase TPE phase TPE /3-phase TP* -/.37 -/.55 -/.75 -/1.1 -/1.5 -/. -/3 -/ -/5.5 -/7.5 -/11 1-/3-phase TPE -/- -/- -/- -/- -/- -/. -/3 -/ -/5.5 -/7.5 -/11 PN PN/ PN/ PN/ PN/ PN/ PN 1 PN 1 PN 1 PN 1 PN 1 PN 1 T min ; T max [ C] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] D1 [mm] /3-phase TP [mm] -/1 -/1 -/1 -/1 -/17 -/17 -/19 -/ -/ -/ -/ 1-/3-phase TPE [mm] -/- -/- -/- -/- -/- -/17 -/17 -/19 -/ -/ -/5 1-/3-phase TP [mm] -/9 -/9 -/9 -/9 -/1 -/1 -/1 -/13 -/13 -/13 -/17 1-/3-phase TPE [mm] -/- -/- -/- -/- -/- -/17 -/17 -/177 -/1 -/1 -/39 AE 1-/3-phase TPE [mm] AF 1-/3-phase TPE [mm] P [mm] B1** [mm] 75/- 75/- /- /- /- 1/31 1/31 1/31 1/31 1/31 1/31 B** [mm] 75/- 75/- /- /- /- 1/31 1/31 1/31 1/31 1/31 1/31 B3 [mm] ** TP [mm] 9/- 9/- 9/- 9/- 1/- 1/31 1/31 1/31 1/3 1/3 175/353 TPE [mm] -/- -/- -/- -/- -/- 17/- 17/- 177/- 1/- 1/- 39/- C1** [mm] /- /- /- /- /- 1/35 1/35 1/35 1/35 1/35 1/35 C5** [mm] / / / / / / C [mm] L1 [mm] H1 [mm] H [mm] /3-phase TP [mm] -/395 -/395 -/7 -/97 -/7 -/577 -/19 -/5 -/71 -/71 -/17 1-/3-phase TPE [mm] -/- -/- -/- -/- -/- -/537 -/5 -/19 -/95 -/711 -/ H [mm] M M1 M1 M1 M1 M1 M1 M1 M1 M1 M1 M1 - and -pole TP and TPD pumps from 1.1 to 9 kw are fitted with motors as standard. The dimension before the slash applies to the single-head pump and the dimension after the slash applies to the twin-head pump. 3

44 Performance curves DN -pole, PN //1 TP, TPD, TPE -XX/ H / -33/ -7/ -/ -1/ -/ TP, TPE Hz Q [m³/h] -39/ -33/ -7/ -/ -1/ -/ Q [m³/h] NPSH -7/, -33/, -39/ H / -/ -7/ -5/ -/ -37/ TP, TPE Hz Q [m³/h] 1-93/ -7/ -5/ -/ -37/ -/ Q [m³/h] NPSH -/ -1/ -/ Q [m³/h] Eta [%] 7 -/ / -33/ -/ -39/ -7/ Q [m³/h] Q [l/s] 1 3 v [m/s] Note: All QH-curves apply to single-head pumps. For further information, see page. TM Q [m³/h] Eta [%] 55-93/ -/ 5-7/ -/ -37/ -5/ Q [m³/h] 1 Q [l/s] v [m/s] TM 37

45 Technical data DN -pole, PN //1 P B3 P Rp 1/ H AF AE D1 B1 B M L1 C5 H H1 H C1 B1 D1 B AE AF AE AF M M L1 C C5 H H1 C1 TM 3 - TM 31 Technical data TP -/ -1/ -/ -7/ -33/ -39/ -37/ -/ -5/ -7/ -/ -93/ TPD TPE TPED Series phase TP IEC size 3-phase TP phase TPE phase TPE /3-phase TP* -/.55 -/.75 -/1.1 -/1.5 -/. -/3 -/ -/5.5 -/7.5 -/11 -/15 -/1.5 1-/3-phase TPE -/- -/- -/- -/- -/- -/- -/ -/5.5 -/7.5 -/11 -/15 -/1.5 PN PN / PN / PN / PN 1 PN 1 PN 1 PN 1 PN 1 PN 1 PN 1 PN 1 PN 1 T min ; T max [ C] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] D1 [mm] 1-/3-phase TP [mm] -/1 -/1 -/1 -/17 -/17 -/17 -/ -/ -/ -/ -/335 -/335 1-/3-phase TPE [mm] -/- -/- -/- -/- -/- -/- -/19 -/ -/ -/5 -/313 -/313 1-/3-phase TP [mm] -/9 -/9 -/9 -/1 -/1 -/1 -/13 -/13 -/13 -/17 -/1 -/1 1-/3-phase TPE [mm] -/- -/- -/- -/- -/- -/- -/177 -/1 -/1 -/39 -/17 -/17 AE 1-/3-phase TPE [mm] AF 1-/3-phase TPE [mm] P [mm] B1** [mm] 5/- 75/- 1/- /- /- /- 19/35 19/35 19/35 19/35 19/35 19/35 B** [mm] 75/- 75/- 1/- /- /- /- 1/31 1/31 1/31 1/31 1/31 1/31 B3 [mm] ** TP [mm] 9/- 9/- 9/- 1/- 1/- 1/- 19/35 1/3 1/3 175/353 1/353 1/353 TPE [mm] -/- -/- -/- -/- -/- -/- 177/- 1/- 1/- 39/- 17/- 17/- C1** [mm] 1/- /- /- 1/- 1/- 1/- 1/35 1/35 1/35 1/35 1/35 1/35 C5** [mm] / / / / / / C [mm] L1 [mm] H1 [mm] H [mm] /3-phase TP [mm] -/39 -/37 -/93 -/ -/5 -/5 -/ -/7 -/7 -/9 -/ -/91 1-/3-phase TPE [mm] -/- -/- -/- -/- -/- -/- -/31 -/77 -/73 -/1 -/ -/ H [mm] M M1 M1 M1 M1 M1 M1 M1 M1 M1 M1 M1 M1 - and -pole TP and TPD pumps from 1.1 to 9 kw are fitted with motors as standard. The dimension before the slash applies to the single-head pump and the dimension after the slash applies to the twin-head pump. 5

46 Performance curves DN -pole, PN //1 TP, TPD, TPE -XX/ H / -3/ -3/ -/ -/ -1/ -/ TP, TPE Hz Q [m³/h] 5-3/ -/ 3 1 -/ -3/ -/ -1/ -/ Q [m³/h] NPSH Eta [%] / -/ -1/ -/, 3/, 3/, / Q [m³/h] -/ -/ -/ -3/ -1/ -3/ -/ Q [m³/h] Q [l/s] v [m/s] TM 3 Note: All QH-curves apply to single-head pumps. For further information, see page.

47 Technical data DN -pole, PN //1 P B3 P Rp 1/ H AF AE D1 B1 B M L1 C5 H H1 H C1 B1 D1 B AE AF AE AF M M L1 C C5 H H1 C1 TM 3 - TM 31 Technical data TP -/ -1/ -/ -/ -3/ -3/ -/ TPD TPE TPED Series phase TP IEC size 3-phase TP phase TPE phase TPE /3-phase TP* -/.55 -/1.1 -/1.5 -/. -/3 -/ -/5.5 1-/3-phase TPE -/- -/- -/- -/. -/3 -/ -/5.5 PN PN/ PN / PN / PN 1 PN 1 PN 1 PN 1 T min ; T max [ C] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] D1 [mm] 1-/3-phase TP [mm] -/1 -/1 -/175 -/17 -/19 -/ -/ 1-/3-phase TPE [mm] -/- -/- -/- -/17 -/17 -/19 -/ 1-/3-phase TP [mm] -/9 -/9 -/1 -/1 -/1 -/13 -/13 1-/3-phase TPE [mm] -/- -/- -/- -/17 -/17 -/177 -/1 AE 1-/3-phase TPE [mm] AF 1-/3-phase TPE [mm] P [mm] B1** [mm] 95/- /- /- 117/5 117/5 133/9 133/9 B** [mm] 3/- /- /- 117/5 117/5 119/ 119/ B3 [mm] ** TP [mm] 9/- 9/- 1/- 117/5 15/ 13/9 1/3 TPE [mm] -/- -/- -/- 17/- 17/- 177/- 1/- C1** [mm] 1/- 1/- 1/- 1/3 1/3 1/ 1/ C5** [mm] / 17/ 17/5 17/5 C [mm] L1 [mm] H1 [mm] H [mm] /3-phase TP [mm] -/3 -/91 -/1 -/5 -/3 -/7 -/73 1-/3-phase TPE [mm] -/- -/- -/- -/5 -/1 -/39 -/715 H [mm] M M1 M1 M1 M1 M1 M1 M1 - and -pole TP and TPD pumps from 1.1 to 9 kw are fitted with motors as standard. The dimension before the slash applies to the single-head pump and the dimension after the slash applies to the twin-head pump. 7

48 Performance curves DN -pole, PN //1 TP, TPD, TPE -XX/ H / -/ -79/ -7/ -5/ -/ TP, TPE Hz Q [m³/h] -7/ -5/ -/ -/ -79/ -/ 3 7 Q [m³/h] NPSH 1 1 Eta [%] Q [m³/h] -7/ -/ -5/ -/ -79/ -/ 3 7 Q [m³/h] 5 15 Q [l/s] v [m/s] TM 39 Note: All QH-curves apply to single-head pumps. For further information, see page.

49 Technical data DN -pole, PN //1 P B3 P Rp 1/ H AF AE D1 B1 B M L1 C5 H H1 H C1 B1 D1 B AE AF AE AF M M L1 C C5 H H1 C1 TM 3 - TM 31 Technical data TP -/ -5/ -7/ -79/ -/ -/ TPD TPE - TPED Series phase TP IEC size 3-phase TP phase TPE phase TPE /3-phase TP* -/7.5 -/11 -/15 -/1.5 -/ -/3 1-/3-phase TPE -/7.5 -/11 -/15 -/1.5 -/ -/- PN PN 1 PN 1 PN 1 PN 1 PN 1 PN 1 T min ; T max [ C] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] D1 [mm] 1-/3-phase TP [mm] -/ -/ -/335 -/335 -/3 -/5 1-/3-phase TPE [mm] -/ -/5 -/313 -/313 -/3 -/- 1-/3-phase TP [mm] -/13 -/17 -/1 -/1 -/5 -/37 1-/3-phase TPE [mm] -/1 -/39 -/17 -/17 -/39 -/- AE 1-/3-phase TPE [mm] AF 1-/3-phase TPE [mm] P [mm] B1** [mm] 1/3 1/3 1/3 1/3 1/3 1/3 B** [mm] 1/379 1/379 1/379 1/379 1/379 1/379 B3 [mm] ** TP [mm] 1/3 1/3 1/3 1/3 5/393 37/13 TPE [mm] 1/- 39/- 17/- 17/- 39/- -/- C1** [mm] 1/ 1/ 1/ 1/ 1/ 1/ C5** [mm] /13 /13 /13 /13 /13 /13 C [mm] L1 [mm] H1 [mm] H [mm] 3 1-/3-phase TP [mm] -/7 -/3 -/ -/9 -/91 -/ 1-/3-phase TPE [mm] -/737 -/ -/ -/7 -/9 -/- H [mm] M M1 M1 M1 M1 M1 M1 - and -pole TP and TPD pumps from 1.1 to 9 kw are fitted with motors as standard. The dimension before the slash applies to the single-head pump and the dimension after the slash applies to the twin-head pump. 9

50 Performance curves DN 5 -pole, PN //1 TP, TPD, TPE 5-XX/ H / -/ -/ -1/ -/ TP, TPE 5 Hz -/ 3 Q [m³/h] -39/ / -/ -3/ -/ -/ -1/ 3 Q [m³/h] NPSH -1/ Eta [%] / -/ -/, -/, -3/, -39/ 3 Q [m³/h] -1/ -3/ -39/ -/ -/ -/ -/ 3 Q [m³/h] 5 15 Q [l/s] v [m/s] TM Note: All QH-curves apply to single-head pumps. For further information, see page.

51 Technical data DN 5 -pole, PN //1 P B3 P Rp 1/ H AF AE D1 B1 B M L1 C5 H H1 H C1 B1 D1 B AE AF AE AF M M L1 C C5 H H1 C1 TM 3 - TM 31 Technical data TP 5 -/ -1/ -/ -/ -/ -3/ -39/ TPD TPE TPED Series phase TP IEC size 3-phase TP phase TPE phase TPE /3-phase TP* -/1.1 -/1.5 -/. -/3 -/ -/5.5 -/7.5 1-/3-phase TPE -/- -/- -/- -/3 -/ -/5.5 -/7.5 PN PN/ PN/ PN/ PN 1 PN 1 PN 1 PN 1 T min ; T max [ C] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] D1 [mm] /3-phase TP [mm] -/1 -/175 -/175 -/19 -/ -/ -/ 1-/3-phase TPE [mm] -/- -/- -/- -/17 -/19 -/ -/ 1-/3-phase TP [mm] -/9 -/1 -/1 -/1 -/13 -/13 -/13 1-/3-phase TPE [mm] -/- -/- -/- -/17 -/177 -/1 -/1 AE 1-/3-phase TPE [mm] AF 1-/3-phase TPE [mm] P [mm] B1** [mm] 93/- /- /- 1/9 1/9 1/9 1/9 B** [mm] 93/- /- /- 1/9 1/9 1/9 1/9 B3 [mm] ** TP [mm] 9/- 1/- 1/- 1/9 1/9 1/3 1/3 TPE [mm] -/- -/- -/- 17/- 177/- 1/- 1/- C1** [mm] 1/- 1/- 1/- 1/ 1/ 1/ 1/ C5** [mm] /5 1/5 1/5 1/5 C [mm] L1 [mm] H1 [mm] H [mm] /3-phase TP [mm] -/519 -/517 -/557 -/1 -/7 -/735 -/735 1-/3-phase TPE [mm] -/- -/- -/- -//7 -//1 -/71 -/73 H [mm] M M1 M1 M1 M1 M1 M1 M1 - and -pole TP and TPD pumps from 1.1 to 9 kw are fitted with motors as standard. The dimension before the slash applies to the single-head pump and the dimension after the slash applies to the twin-head pump. 51

52 Performance curves DN 5 -pole, PN //1 TP, TPD, TPE 5-XX/ H / -9/ -7/ -3/ -5/ -/ TP, TPE 5 Hz 3 Q [m³/h] 35 -/ / -5/ -/ -7/ -9/ Q [m³/h] NPSH Eta [%] Q [m³/h] -/ -5/ -3/ -7/ -9/ -/ Q [m³/h] 3 Q [l/s] v [m/s] TM 1 Note: All QH-curves apply to single-head pumps. For further information, see page. 5

53 Technical data DN 5 -pole, PN //1 P B3 P Rp 1/ H AF AE D1 B1 B M L1 C5 H H1 H C1 B1 D1 B AE AF AE AF M M L1 C C5 H H1 C1 TM 3 - TM 31 Technical data TP 5 -/ -5/ -3/ -7/ -9/ -/ TPD TPE - - TPED Series phase TP IEC size 3-phase TP phase TPE phase TPE /3-phase TP* -/11 -/15 -/1.5 -/ -/3 -/37 1-/3-phase TPE -/11 -/15 -/1.5 -/ -/- -/- PN PN 1 PN 1 PN 1 PN 1 PN 1 PN 1 T min ; T max [ C] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] D1 [mm] /3-phase TP [mm] -/ -/335 -/335 -/3 -/5 -/5 1-/3-phase TPE [mm] -/5 -/313 -/313 -/3 -/- -/- 1-/3-phase TP [mm] -/17 -/1 -/1 -/5 -/37 -/37 1-/3-phase TPE [mm] -/39 -/17 -/17 -/39 -/- -/- AE 1-/3-phase TPE [mm] AF 1-/3-phase TPE [mm] P [mm] B1** [mm] 17/39 17/39 17/39 17/39 17/39 17/39 B** [mm] 1/33 1/33 1/33 1/33 1/33 1/33 B3 [mm] ** TP [mm] 17/395 1/395 1/395 5/3 37/3 37/3 TPE [mm] 39/- 17/- 17/- 39/- -/- -/- C1** [mm] 1/5 1/5 1/5 1/5 1/5 1/5 C5** [mm] 3/111 3/111 3/111 3/111 3/111 3/111 C [mm] L1 [mm] H1 [mm] H [mm] /3-phase TP [mm] -/5 -/91 -/935 -/99 -/57 -/57 1-/3-phase TPE [mm] -/37 -/9 -/7 -/913 -/- -/- H [mm] M M1 M1 M1 M1 M1 M1 - and -pole TP and TPD pumps from 1.1 to 9 kw are fitted with motors as standard. The dimension before the slash applies to the single-head pump and the dimension after the slash applies to the twin-head pump. 53

54 Performance curves DN -pole, PN //1 TP, TPD, TPE -XX/ H / -/ -/ -1/ TP, TPE Hz H 7-7/ -/ -53/ -/ -/ -33/ TP, TPE Hz Q [m³/h] -/ -1/ -9/ -/ 3 7 Q [m³/h] NPSH -1/ Q [m³/h] 3-7/ / -53/ -/ -/ -/ 1 1 1Q [m³/h] NPSH 1 -/ -/, -9/ -33/, -/ -/, -53/, -/, -7/ Eta [%] Q [m³/h] -9/ -/ -/ -1/ Eta [%] Q [m³/h] -7/ -/ -33/ -53/ -/ -/ Q [m³/h] Q [m³/h] Q [l/s] v [m/s] TM 1 3 Q [l/s] v [m/s] TM 79 1 Note: All QH-curves apply to single-head pumps. For further information, see page. 5

55 Technical data DN -pole, PN //1 P B3 P Rp 1/ H AF AE D1 B1 B M L1 C5 H H1 H C1 B1 D1 B AE AF AE AF M M L1 C C5 H H1 C1 TM TM Technical data TP -1/ -/ -/ -9/ -33/ -/ -/ -53/ -/ -7/ TPD - TPE TPED Series phase TP IEC size 3-phase TP phase TPE phase TPE /3-phase TP* -/3 -/ -/5.5 -/7.5 -/11 -/15 -/1.5 -/ -/3 -/37 1-/3-phase TPE -/- -/ -/5.5 -/7.5 -/11 -/15 -/1.5 -/ -/- -/- PN PN /PN PN 1 PN 1 PN 1 PN 1 PN 1 PN 1 PN 1 PN 1 PN 1 T min ; T max [ C] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] D1 [mm] 1-/3-phase TP [mm] -/175 -/ -/ -/ -/ -/3 -/335 -/3 -/5 -/5 1-/3-phase TPE [mm] -/- -/19 -/ -/ -/5 -/313 -/313 -/3 -/- -/- 1-/3-phase TP [mm] -/1 -/13 -/13 -/13 -/17 -/197 -/1 -/5 -/37 -/37 1-/3-phase TPE [mm] -/- -/177 -/1 -/1 -/39 -/17 -/17 -/39 -/- -/- AE 1-/3-phase TPE [mm] AF 1-/3-phase TPE [mm] P [mm] B1** [mm] 15/- 15/ 15/ 15/ 1/3 1/3 1/1 1/1 1/1 1/1 B** [mm] /- 133/9 133/9 133/9 17/35 17/35 17/5 17/5 17/5 17/5 B3 [mm] ** TP [mm] 1/- 13/95 1/3 1/3 17/ /375 1/1 5/1 37/3 37/3 TPE [mm] -/- 177/- 1/- 1/- 39/- 17/- 17/- 39/- -/- -/- C1** [mm] 1/- 1/ 1/ 1/ 1/ 1/ 1/5 1/5 1/5 1/5 C5** [mm] 1 1/7 1/7 1/7 /93 /93 /133 /133 /133 /133 C [mm] L1 [mm] H1 [mm] H [mm] /3-phase TP [mm] -/ -/1 -/739 -/739 -/5 -/ -/935 -/99 -/57 -/57 1-/3-phase TPE [mm] -/- -/ -/7 -/7 -/37 -/9 -/7 -/913 -/- -/- H [mm] M M1 M1 M1 M1 M1 M1 M1 M1 M1 M1 - and -pole TP and TPD pumps from 1.1 to 9 kw are fitted with motors as standard. The dimension before the slash applies to the single-head pump and the dimension after the slash applies to the twin-head pump. 55

56 Performance curves DN -pole, PN //1 TP, TPD, TPE -XX/ H / -3/ -3/ TP, TPE Hz 1 1 Q [m³/h] -3/ -37/ -3/ 1 1 Q [m³/h] NPSH -3/ -3/, -37/ H / -3/ -53/ -3/ -3/ TP, TPE Hz 1 1 Q [m³/h] -3/ -53/ -7/ -3/ -3/ 1 1 Q [m³/h] NPSH -53/, -3/, -7/ 1 1-3/, -3/ Eta [%] Q [m³/h] Eta [%] Q [m³/h] -7/ / -3/ -3/ / -3/ -3/ -53/ Q [m³/h] Q [m³/h] 3 Q [l/s] 1 3 v [m/s] TM Q [l/s] v [m/s] TM Note: All QH-curves apply to single-head pumps. For further information, see page. 5

57 Technical data DN -pole, PN //1 P B3 P Rp 1/ H AF AE D1 B1 B M L1 C5 H H1 H C1 B1 D1 B AE AF AE AF M M L1 C C5 H H1 C1 TM TM Technical data TP -3/ -3/ -37/ -3/ -3/ -53/ -3/ -7/ TPD TPE TPED Series phase TP IEC size 3-phase TP phase TPE phase TPE /3-phase TP* -/7.5 -/11 -/15 -/1.5 -/ -/3 -/37 -/5 1-/3-phase TPE -/7.5 -/11 -/15 -/1.5 -/ -/- -/- -/- PN PN 1 PN 1 PN 1 PN 1 PN 1 PN 1 PN 1 PN 1 T min ; T max [ C] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] D1 [mm] 1-/3-phase TP [mm] -/ -/ -/3 -/3 -/33 -/ -/ -/ 1-/3-phase TPE [mm] -/ -/5 -/313 -/313 -/3 -/- -/- -/- 1-/3-phase TP [mm] -/13 -/17 -/197 -/197 -/5 -/35 -/35 -/35 1-/3-phase TPE [mm] -/1 -/39 -/17 -/17 -/39 -/- -/- -/- AE 1-/3-phase TPE [mm] AF 1-/3-phase TPE [mm] P [mm] B1** [mm] 1/37 1/37 1/37 151/1 151/1 173/3 173/3 173/3 B** [mm] 15/33 15/33 15/33 19/395 19/395 1/9 1/9 1/9 B3 [mm] 7 7 ** TP [mm] 15/3 175/ / /1 5/17 35/51 35/51 35/75 TPE [mm] 1/- 39/- 17/- 17/- 39/- -/- -/- -/- C1** [mm] 1/ 1/ 1/ 3/5 3/5 3/5 3/5 3/5 C5** [mm] / / / 75/1 75/1 75/1 75/1 75/1 C [mm] L1 [mm] H1 [mm] H [mm] /3-phase TP [mm] -/77 -/79 -/93 -/9 -/1 -/1 -/1 -/11 1-/3-phase TPE [mm] -/757 -/ -/7 -/99 -/935 -/- -/- -/- H [mm] M M1 M1 M1 M1 M1 M1 M1 M1 - and -pole TP and TPD pumps from 1.1 to 9 kw are fitted with motors as standard. The dimension before the slash applies to the single-head pump and the dimension after the slash applies to the twin-head pump. 57

58 Performance curves DN 3 -pole, PN //1 TP, TPD, TPE, -pole, PN //1 TP, TPD, TPE 3-XXX/ H / TP, TPE 3 Hz H / -1/ TP, TPE 3 Hz 3 1 -/ 1-1/ Q [m³/h].1.1 -/ / Q [m³/h] NPSH / -/ Q [m³/h] 1 1 Q [m³/h] NPSH / -1/ -19/. Eta Q [m³/h] [%] / -/ 3 5 Q [m³/h]. Eta [%] Q [m³/h] -1/ -19/ -1/ 1 1 Q [m³/h] 1 3 Q [l/s] 1 3 v [m/s] TM 1 3 Q [l/s] 1 3 v [m/s] TM 7 Note: All QH-curves apply to single-head pumps. For further information, see page. 5

59 Technical data DN 3 -pole, PN //1 P B3 P Rp 1/ H AF AE D1 B1 B M L1 C5 H H1 H C1 B1 D1 B AE AF AE AF M M L1 C C5 H H1 C1 TM 3 - TM 31 Technical data TP 3 -/ -/ -1/ -1/ -19/ TPD TPE TPED Series phase TP IEC size 3-phase TP phase TPE phase TPE /3-phase TP* -/.1 -/.5 -/.55 -/.75 -/1.1 1-/3-phase TPE -/- -/- -/- -/- -/1.1 PN PN/ PN/ PN 1 PN 1 PN 1 T min ; T max [ C] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] D1 [mm] /3-phase TP [mm] -/1 -/15 -/11 -/11 -/17 1-/3-phase TPE [mm] -/- -/- -/- -/- -/17 1-/3-phase TP [mm] -/37 -/395 -/9 -/9 -/1 1-/3-phase TPE [mm] -/- -/- -/- -/- -/17 AE 1-/3-phase TPE [mm] AF 1-/3-phase TPE [mm] P [mm] - - B1** [mm] 75/- /- 1/31 1/31 1/31 B** [mm] 75/- /- 1/31 1/31 1/31 B3 [mm] ** TP [mm] 37/- 395/- 1/31 1/31 1/31 TPE [mm] -/- -/- -/- -/- 17/- C1** [mm] /- /- 1/35 1/35 1/35 C5** [mm] 1 1 / / / C [mm] L1 [mm] H1 [mm] 79 H [mm] /3-phase TP [mm] -/1 -/7 -/7 -/7 -/537 1-/3-phase TPE [mm] -/- -/- -/- -/- -/537 H [mm] M M1 M1 M1 M1 M1 - and -pole TP and TPD pumps from 1.1 to 9 kw are fitted with motors as standard. The dimension before the slash applies to the single-head pump and the dimension after the slash applies to the twin-head pump. 59

60 Performance curves DN -pole, PN //1 TP, TPD, TPE -XXX/ H / -/ TP, TPE Hz H / -19/ -1/ -1/ TP, TPE Hz Q [m³/h] 1 1 Q [m³/h].5. -/. 1. -/ / / -1/ -1/ Q [m³/h] NPSH Eta [%] / -/ Q [m³/h] -/ -/ Q [m³/h]. 1 1 Q [m³/h] NPSH Eta [%] Q [m³/h] -/ -1/ -1/ -19/ 1 1 Q [m³/h] Q [l/s] 1 3 v [m/s] TM Q [l/s] 1 3 v [m/s] TM 9 Note: All QH-curves apply to single-head pumps. For further information, see page.

61 Technical data DN -pole, PN //1 P B3 P Rp 1/ H AF AE D1 B1 B M L1 C5 H H1 H C1 B1 D1 B AE AF AE AF M M L1 C C5 H H1 C1 TM 3 - TM 31 Technical data TP -/ -/ -1/ -1/ -19/ -/ TPD TPE - - TPED Series phase TP IEC size 3-phase TP phase TPE phase TPE /3-phase TP* -/.5 -/.55 -/.75 -/1.1 -/1.5 -/. 1-/3-phase TPE -/- -/- -/.75 -/1.1 -/1.5 -/. PN PN / PN / PN 1 PN 1 PN 1 PN 1 T min ; T max [ C] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] D1 [mm] 1-/3-phase TP [mm] -/1 -/1 -/11 -/17 -/17 -/19 1-/3-phase TPE [mm] -/- -/- -/11 -/17 -/17 -/17 1-/3-phase TP [mm] -/9 -/9 -/9 -/1 -/1 -/1 1-/3-phase TPE [mm] -/- -/- -/1 -/17 -/17 -/17 AE 1-/3-phase TPE [mm] AF 1-/3-phase TPE [mm] P [mm] - - B1** [mm] 5/- /- 19/35 19/35 19/35 19/35 B** [mm] 75/- /- 1/31 1/31 1/31 1/31 B3 [mm] ** TP [mm] 9/- 9/- 19/35 19/35 19/35 19/35 TPE [mm] -/- -/- 19/- 17/- 17/- 17/- C1** [mm] 1/- 1/- 1/35 1/35 1/35 1/35 C5** [mm] / / / / C [mm] L1 [mm] H1 [mm] H [mm] /3-phase TP [mm] -/39 -/1 -/99 -/59 -/59 -/31 1-/3-phase TPE [mm] -/- -/- -/519 -/59 -/59 -/17 H [mm] M M1 M1 M1 M1 M1 M1 - and -pole TP and TPD pumps from 1.1 to 9 kw are fitted with motors as standard. The dimension before the slash applies to the single-head pump and the dimension after the slash applies to the twin-head pump. 1

62 Performance curves DN -pole, PN //1 TP, TPD, TPE -XXX/ H / -1/ -1/ -/ TP, TPE Hz H 3 3-3/ -7/ -/ -19/ TP, TPE Hz -/ Q [m³/h] -1/ -1/ -/ -1/ -/ 1 1 Q [m³/h] NPSH -/ Eta [%] / -1/, -1/, -1/ 1 1 Q [m³/h] -/ -1/ -1/ -1/ -/ 1 1 Q [m³/h] Q [m³/h] Q [m³/h] NPSH Eta [%] / -/ -7/ -3/ Q [m³/h] -7/ -3/ -19/ -/ Q [m³/h] Q [l/s] 1 3 v [m/s] TM 1 Q [l/s] v [m/s] TM 51 Note: All QH-curves apply to single-head pumps. For further information, see page.

63 Technical data DN -pole, PN //1 P B3 P Rp 1/ H AF AE D1 B1 B M L1 C5 H H1 H C1 B1 D1 B AE AF AE AF M M L1 C C5 H H1 C1 TM 3 - TM 31 Technical data TP -/ -/ -1/ -1/ -1/ -19/ -/ -7/ -3/ TPD TPE - - TPED Series phase TP IEC size 3-phase TP phase TPE phase TPE /3-phase TP* -/.5 -/.55 -/.75 -/1.1 -/1.5 -/. -/3 -/ -/5.5 1-/3-phase TPE -/- -/- -/.75 -/1.1 -/1.5 -/. -/3 -/ -/5.5 PN PN / PN / PN 1 PN 1 PN 1 PN 1 PN 1 PN 1 PN 1 T min ; T max [ C] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] D1 [mm] 1-/3-phase TP [mm] -/1 -/1 -/11 -/17 -/17 -/19 -/19 -/ -/ 1-/3-phase TPE [mm] -/- -/- -/11 -/17 -/17 -/17 -/17 -/19 -/ 1-/3-phase TP [mm] -/9 -/9 -/9 -/1 -/1 -/1 -/1 -/13 -/13 1-/3-phase TPE [mm] -/- -/- -/1 -/17 -/17 -/17 -/17 -/177 -/1 AE 1-/3-phase TPE [mm] AF 1-/3-phase TPE [mm] P [mm] B1** [mm] 9/- 1/- 1/3 1/3 1/3 1/3 1/3 1/3 1/3 B** [mm] 75/- /- 1/379 1/379 1/379 1/379 1/379 1/379 1/379 B3 [mm] - - ** TP [mm] 9/- 9/- 1/3 1/3 1/3 1/3 1/3 1/3 1/3 TPE [mm] -/- -/- -/- 1/- 1/- 1/- 1/- 1/- 1/- C1** [mm] 1/- 1/- 1/ 1/ 1/ 1/ 1/ 1/ 1/ C5** [mm] 1 1 /13 /13 /13 /13 /13 /13 /13 C [mm] L1 [mm] H1 [mm] H [mm] /3-phase TP [mm] -/9 -/53 -/513 -/53 -/53 -/5 -/5 -/ -/7 1-/3-phase TPE [mm] -/- -/- -/533 -/53 -/53 -/31 -/31 -/5 -/71 H [mm] M M1 M1 M1 M1 M1 M1 M1 M1 M1 - and -pole TP and TPD pumps from 1.1 to 9 kw are fitted with motors as standard. The dimension before the slash applies to the single-head pump and the dimension after the slash applies to the twin-head pump. 3

64 Performance curves DN 5 -pole, PN //1 TP, TPD, TPE 5-XXX/ H / -13/ -/ TP, TPE 5 Hz H / -3/ -3/ -19/ TP, TPE 5 Hz -/ Q [m³/h] -13/ -/ -1/ -/ Q [m³/h] NPSH 7 -/ Q [m³/h] 3 Q [m³/h] NPSH -19/ -3/ -3/ -33/ 5 3 -/ 3 1 Eta [%] 75-13/, -1/ Q [m³/h] 1 Eta [%] 7 3 Q [m³/h] -3/ / -1/ / -3/ -33/ 5 -/ -/ Q [m³/h] 35 3 Q [m³/h] 1 1 Q [l/s] v [m/s] TM Q [l/s] v [m/s] TM 53 Note: All QH-curves apply to single-head pumps. For further information, see page.

65 Technical data DN 5 -pole, PN //1 P B3 P Rp 1/ H AF AE D1 B1 B M L1 C5 H H1 H C1 B1 D1 B AE AF AE AF M M L1 C C5 H H1 C1 TM 3 - TM 31 Technical data TP 5 -/ -/ -13/ -1/ -19/ -3/ -3/ -33/ TPD TPE - - TPED Series phase TP IEC size 3-phase TP phase TPE phase TPE /3-phase TP* -/.37 -/1.1 -/1.5 -/. -/3 -/ -/5.5 -/7.5 1-/3-phase TPE -/- -/- -/1.5 -/. -/3 -/ -/5.5 -/7.5 PN PN / PN / PN 1 PN 1 PN 1 PN 1 PN 1 PN 1 T min ; T max [ C] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] D1 [mm] /3-phase TP [mm] -/1 -/175 -/17 -/19 -/19 -/ -/7 -/7 1-/3-phase TPE [mm] -/- -/- -/17 -/17 -/17 -/19 -/ -/5 1-/3-phase TP [mm] -/9 -/1 -/1 -/1 -/1 -/13 -/19 -/19 1-/3-phase TPE [mm] -/- -/- -/17 -/17 -/17 -/177 -/1 -/39 AE 1-/3-phase TPE [mm] AF 1-/3-phase TPE [mm] P [mm] B1** [mm] 15/- 15/- 17/39 17/39 17/39 17/39 17/39 17/39 B** [mm] /- /- 1/33 1/33 1/33 1/33 1/33 1/33 B3 [mm] - - ** TP [mm] 9/- 1/- 17/33 17/33 17/33 17/33 19/33 19/33 TPE [mm] -/- -/- 17/- 17/- 17/- 17/- 1/- 39/- C1** [mm] 1/- 1/- 1/5 1/5 1/5 1/5 1/5 1/5 C5** [mm] /111 3/111 3/111 3/111 3/111 3/111 C [mm] L1 [mm] H1 [mm] H [mm] /3-phase TP [mm] -/ -/53 -/1 -/5 -/5 -/91 -/777 -/15 1-/3-phase TPE [mm] -/- -/- -/57 -/ -/ -/5 -/73 -/37 H [mm] M M1 M1 M1 M1 M1 M1 M1 M1 - and -pole TP and TPD pumps from 1.1 to 9 kw are fitted with motors as standard. The dimension before the slash applies to the single-head pump and the dimension after the slash applies to the twin-head pump. 5

66 Performance curves DN -pole, PN //1 TP, TPD, TPE -XXX/ H / -1/ -1/ -/ -/ TP, TPE Hz H / -/ -/ -3/ -/ -3/ TP, TPE Hz Q [m³/h]. -17/ / -1/ -1/ -/ 3 7 Q [m³/h] NPSH 7 -/ 5 -/ Q [m³/h] 1 1 Q [m³/h] NPSH -/, -3/, -/ 7 -/, -5/ 5 -/ -3/ -3/ -/ -5/ -/ 3-1/ 3-3/ 1-1/, -17/ 1 Eta [%] Q [m³/h] -1/ -17/ -1/ Eta [%] Q [m³/h] -/ -3/ -5/ -3/ -/ -/ 55 -/ -/ Q [m³/h] 1 1 Q [m³/h] 5 15 Q [l/s] 1 3 v [m/s] TM Q [l/s] v [m/s] TM 77 1 Note: All QH-curves apply to single-head pumps. For further information, see page.

67 Technical data DN -pole, PN //1 P B3 P Rp 1/ H AF AE D1 B1 B M L1 C5 H H1 H C1 B1 D1 B AE AF AE AF M M L1 C C5 H H1 C1 TM TM Technical data TP -/ -/ -1/ -1/ -17/ -3/ -/ -3/ -/ -/ -5/ TPD TPE - - TPED Series phase TP IEC size 3-phase TP phase TPE phase TPE /3-phase TP* -/.75 -/1.5 -/. -/3 -/ -/5.5 -/7.5 -/11 -/15 -/1.5 -/ 1-/3-phase TPE -/- -/- -/. -/3 -/ -/5.5 -/7.5 -/11 -/15 -/1.5 -/ PN PN /PN PN /PN PN 1 PN 1 PN 1 PN 1 PN 1 PN 1 PN 1 PN 1 PN 1 T min ; T max [ C] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] D1 [mm] 1-/3-phase TP [mm] -/1 -/175 -/19 -/19 -/ -/7 -/7 -/3 -/3 -/33 -/33 1-/3-phase TPE [mm] -/- -/- -/17 -/19 -/19 -/ -/5 -/5 -/313 -/313 -/3 1-/3-phase TP [mm] -/9 -/1 -/1 -/1 -/13 -/19 -/19 -/197 -/197 -/5 -/5 1-/3-phase TPE [mm] -/- -/- -/17 -/177 -/177 -/1 -/39 -/39 -/17 -/17 -/39 AE 1-/3-phase TPE [mm] AF 1-/3-phase TPE [mm] P [mm] B1** [mm] 13/- 135/- 1/3 1/1 1/1 /91 /91 /91 /91 /91 /91 B** [mm] /- /- 17/35 17/5 17/5 3/ 3/ 3/ 3/ 3/ 3/ B3 [mm] ** TP [mm] 9/- 1/- 17/3 17/1 17/1 3/91 3/91 3/91 3/91 5/91 5/91 TPE [mm] -/- -/- 17/- 17/- 17/- 3/- 39/- 39/- 17/- 17/- 39/- C1** [mm] 1/- 1/- 1/ 1/5 1/5 3/5 3/5 3/5 3/5 3/5 3/5 C5** [mm] 1 1 /93 /133 /133 3/5 3/5 3/5 3/5 3/5 3/5 C [mm] L1 [mm] 3 3 H1 [mm] H [mm] /3-phase TP [mm] -/513 -/59 -/5 -/5 -/91 -/33 -/71 -/91 -/91 -/5 -/5 1-/3-phase TPE [mm] -/- -/- -/ -/5 -/5 -/75 -/9 -/9 -/9 -/9 -/9 H [mm] M M1 M1 M1 M1 M1 M1 M1 M1 M1 M1 M1 - and -pole TP and TPD pumps from 1.1 to 9 kw are fitted with motors as standard. The dimension before the slash applies to the single-head pump and the dimension after the slash applies to the twin-head pump. 7

68 Performance curves DN -pole, PN //1 TP, TPD, TPE -XXX/ H / -13/ -/ -/ -/ TP, TPE Hz Q [m³/h] -/ -13/ -17/ -/ -/ Q [m³/h] NPSH -/ -13/, -17/ -/ -/ H / -39/ -3/ -9/ -/ -/ TP, TPE Hz Q [m³/h] Q [m³/h] NPSH 1 -/ -/ -7/ -39/ -3/ -9/ -9/, -3/, -39/, -7/ -/, -/ Eta [%] Q [m³/h] -/ -13/ -17/ -/ -/ Q [m³/h] Eta [%] Q [m³/h] -9/ -/ -7/ -3/ -39/ -/ Q [m³/h] Q [l/s] v [m/s] TM Q [l/s] v [m/s] TM Note: All QH-curves apply to single-head pumps. For further information, see page.

69 Technical data DN -pole, PN //1 P B3 P Rp 1/ H AF AE D1 B1 B M L1 C5 H H1 H C1 B1 D1 B AE AF AE AF M M L1 C C5 H H1 C1 TM TM Technical data TP -/ -/ -/ -13/ -17/ -/ -/ -9/ -3/ -39/ -7/ TPD TPE TPED Series phase TP IEC size 3-phase TP phase TPE phase TPE /3-phase TP* -/1.1 -/. -/3 -/ -/5.5 -/7.5 -/11 -/15 -/1.5 -/ -/3 1-/3-phase TPE -/- -/- -/3 -/ -/5.5 -/7.5 -/11 -/15 -/1.5 -/ -/- PN PN/PN PN /PN PN 1 PN 1 PN 1 PN 1 PN 1 PN 1 PN 1 PN 1 PN 1 T min ; T max [ C] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] D1 [mm] 1-/3-phase TP [mm] -/175 -/175 -/19 -/ -/7 -/7 -/3 -/3 -/33 -/33 -/ 1-/3-phase TPE [mm] -/- -/- -/19 -/19 -/ -/5 -/5 -/313 -/313 -/3 -/- 1-/3-phase TP [mm] -/1 -/1 -/1 -/13 -/19 -/17 -/197 -/197 -/5 -/5 -/35 1-/3-phase TPE [mm] -/- -/- -/177 -/177 -/1 -/39 -/39 -/17 -/17 -/39 -/- AE 1-/3-phase TPE [mm] AF 1-/3-phase TPE [mm] P [mm] B1** [mm] 17/- 17/- 151/1 173/3 173/3 9/579 9/579 9/579 9/579 9/579 9/579 B** [mm] 1/- 1/- 19/395 1/9 1/9 9/51 9/51 9/51 9/51 9/51 9/51 B3 [mm] ** TP [mm] 1/- 1/- 19/1 1/3 1/3 9/579 9/579 9/579 9/579 9/579 35/579 TPE [mm] -/- -/- 19/- 1/- 1/- 39/- 39/- 17/- 17/- 39/- -/- C1** [mm] /- /- 3/5 3/5 3/5 3/ 3/ 3/ 3/ 3/ 3/ C5** [mm] /1 75/1 75/1 335/1 335/1 335/1 335/1 335/1 335/1 C [mm] L1 [mm] H1 [mm] H [mm] /3-phase TP [mm] -/55 -/ -/7 -/773 -/37 -/ -/91 -/1 -/5 -/5 -/11 1-/3-phase TPE [mm] -/- -/- -/7 -/73 -/79 -/9 -/93 -/9 -/9 -/ -/- H [mm] M M1 M1 M1 M1 M1 M1 M1 M1 M1 M1 M1 - and -pole TP and TPD pumps from 1.1 to 9 kw are fitted with motors as standard. The dimension before the slash applies to the single-head pump and the dimension after the slash applies to the twin-head pump. 9

70 Performance curves DN 15 -pole, PN //1 TP, TPD, TPE 15-XXX/ H / -/ -1/ -13/ TP, TPE 15 Hz Q [m³/h] -/ -/ -1/ -13/ Q [m³/h] NPSH H / -3/ -3/ -3/ TP, TPE 15 Hz 1 1 Q [m³/h] 1 1 Q [m³/h] NPSH 7-3/ -3/ -3/ -9/ /, -/ -13/, -1/ 5 3 Eta [%] Q [m³/h] -/ -/ -1/ -13/ 1 Eta [%] Q [m³/h] -3/ -3/ -9/ -3/ Q [m³/h] 1 1 Q [m³/h] 3 Q [l/s] 1 3 v [m/s] TM Q [l/s] v [m/s] TM Note: All QH-curves apply to single-head pumps. For further information, see page. 7

71 Technical data DN 15 -pole, PN //1 P B3 P Rp 1/ H AF AE D1 B1 B M L1 C5 H H1 H C1 B1 D1 B AE AF AE AF M M L1 C C5 H H1 C1 TM TM Technical data TP 15-13/ -1/ -/ -/ -3/ -3/ -3/ -9/ TPD TPE - - TPED Series phase TP IEC size 3-phase TP phase TPE phase TPE /3-phase TP* -/5.5 -/7.5 -/11 -/15 -/1.5 -/ -/3 -/37 1-/3-phase TPE -/5.5 -/7.5 -/11 -/15 -/1.5 -/ -/- -/- PN PN 1 PN 1 PN 1 PN 1 PN 1 PN 1 PN 1 PN 1 T min ; T max [ C] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] D1 [mm] /3-phase TP [mm] -/7 -/7 -/3 -/3 -/33 -/33 -/ -/ 1-/3-phase TPE [mm] -/ -/5 -/5 -/313 -/313 -/3 -/- -/- 1-/3-phase TP [mm] -/19 -/19 -/197 -/197 -/5 -/5 -/35 -/35 1-/3-phase TPE [mm] -/1 -/39 -/39 -/17 -/17 -/39 -/- -/- AE 1-/3-phase TPE [mm] AF 1-/3-phase TPE [mm] P [mm] B1** [mm] /537 /537 3/5 3/5 3/5 3/5 3/5 3/5 B** [mm] /51 /51 71/55 71/55 71/55 71/55 71/55 71/55 B3 [mm] ** TP [mm] /537 /537 71/5 71/5 71/5 71/5 35/5 35/5 TPE [mm] /- 39/- 39/- 17/- 17/- 39/- -/- -/- C1** [mm] 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ C5** [mm] 3/ 3/ /175 /175 /175 /175 /175 /175 C [mm] L1 [mm] H1 [mm] H [mm] /3-phase TP [mm] -/917 -/955 -/11 -/51 -/1135 -/1135 -/119 -/11 1-/3-phase TPE [mm] -/7 -/99 -/9 -/3 -/3 -/5 -/- -/- H [mm] M M1 M1 M1 M1 M1 M1 M1 M1 - and -pole TP and TPD pumps from 1.1 to 9 kw are fitted with motors as standard. The dimension before the slash applies to the single-head pump and the dimension after the slash applies to the twin-head pump. 71

72 Performance curves DN 1 -pole, PN //1 TP, TPD, TPE 1-XXX/ H / -/ -/ -1/ TP, TPE 1 Hz Q [m³/h] -3/ H / -3/ TP, TPE 1 Hz Q [m³/h] 5 -/ -/ 3-3/ -/ 15-1/ Q [m³/h] NPSH Q [m³/h] NPSH 1-3/ Eta [%] Q [m³/h] -3/ -/ -/ -1/ Q [m³/h] 1 Eta [%] / Q [m³/h] -3/ -/ Q [m³/h] Q [l/s] v [m/s] TM 77 1 Q [l/s] v [m/s] TM3 5 Note: All QH-curves apply to single-head pumps. For further information, see page. 7

73 Technical data DN 1 -pole, PN //1 P B3 P Rp 1/ H AF AE D1 B1 B M L1 C5 H H1 H C1 B1 D1 B AE AF AE AF M M L1 C C5 H H1 C1 TM TM Technical data TP 1-1/ -/ -/ -3/ -3/ -/ TPD - - TPE TPED Series phase TP IEC size 3-phase TP phase TPE phase TPE /3-phase TP* -/15 -/1.5 -/ -/3 -/3 -/37 1-/3-phase TPE -/15 -/1.5 -/ -/- -/- -/- PN PN 1 PN 1 PN 1 PN 1 PN 1 PN 1 T min ; T max [ C] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] D1 [mm] /3-phase TP [mm] -/3 -/33 -/33 -/ -/ -/ 1-/3-phase TPE [mm] -/313 -/313 -/3 -/- -/- -/- 1-/3-phase TP [mm] -/197 -/5 -/5 -/35 -/35 -/35 1-/3-phase TPE [mm] -/17 -/17 -/39 -/- -/- -/- AE 1-/3-phase TPE [mm] AF 1-/3-phase TPE [mm] P [mm] B1** [mm] 37/53 37/53 37/53 37/53 93/- 93/- B** [mm] 9/553 9/553 9/553 9/553 /- /- B3 [mm] - - ** TP [mm] 9/53 9/53 9/53 35/53 35/- 35/- TPE [mm] 17/- 17/- 39/- -/- -/- -/- C1** [mm] 3/ 3/ 3/ 3/ 3/- 3/- C5** [mm] /153 /153 /153 /153 /- /- C [mm] L1 [mm] H1 [mm] H [mm] /3-phase TP [mm] -/55 -/1139 -/1139 -/1195 -/11 -/113 1-/3-phase TPE [mm] -/3 -/3 -/ -/- -/- -/- H [mm] M M1 M1 M1 M1 M1 M1 - and -pole TP and TPD pumps from 1.1 to 9 kw are fitted with motors as standard. The dimension before the slash applies to the single-head pump and the dimension after the slash applies to the twin-head pump. 73

74 Performance curves DN 1 -pole, PN TP 1-XXX/ H / -9/ -/ -3/ TP 1 Hz Q [m³/h] -3/ -5/ -9/ -/ Q [m³/h] NPSH Eta [%] Q [m³/h] -3/ -5/ -9/ -/ Q [m³/h] 1 1Q [l/s] v [m/s] TM 3 7

75 Technical data DN 1 -pole, PN P D1D Rp 3/ L3 L1 H1 H L D1S C C Rp 3/ C C7 ø B B9 B1 B B7 TM 39 3 Technical data TP 1-3/ -/ -9/ -5/ TPD TPE TPED Series 1-phase TP IEC size 3-phase TP 5 S 5 M M S 1-phase TPE phase TPE PN T min ; T max [ C] [-5;1] [-5;1] [-5;1] [-5;1] D1 D /D1 S [mm] / / / / [mm] [mm] P [mm] B1 [mm] B [mm] [mm] B7 [mm] B [mm] B9 [mm] C [mm] C7 [mm] C [mm] Ø [mm] L1 [mm] L [mm] L3 [mm] H1 [mm] H [mm] [mm] and -pole TP and TPD pumps from 1.1 to 9 kw are fitted with motors as standard. 75

76 Performance curves DN -pole, PN 1 TP -XXX/ H / -9/ -7/ TP, TPE Hz Q [m³/h] -7/ -33/ -9/ 3 Q [m³/h] NPSH 1 1-7/, -9/, -33/ 3 Q [m³/h] Eta [%] / -9/ -33/ 3 Q [m³/h] 1 Q [l/s] v [m/s] TM3 53 7

77 Technical data DN -pole, 1 P Rp 1/ H1 H D1 B1 B L1 H M AF AE C5 C1 TM Technical data TP -7/ -9/ -33/ TPD TPE TPED Series phase TP IEC size 3-phase TP phase TPE phase TPE /3-phase TP* -/37 -/5 -/55 1-/3-phase TPE -/- -/- -/- PN PN 1 PN 1 PN 1 T min ; T max [ C] [-5;1] [-5;1] [-5;1] D1 [mm] 1-/3-phase TP [mm] -/ -/ -/95 1-/3-phase TPE [mm] -/- -/- -/- 1-/3-phase TP [mm] -/35 -/35 -/39 1-/3-phase TPE [mm] -/- -/- -/- AE 1-/3-phase TPE [mm] AF 1-/3-phase TPE [mm] P [mm] 5 B1** [mm] 33/- 33/- 33/- B** [mm] 79/- 79/- 79/- B3 [mm] ** TP [mm] 33/- 33/- 39/- TPE [mm] -/- -/- -/- C1** [mm] /- /- /- C5** [mm] /- /- /- C [mm] L1 [mm] H1 [mm] H [mm] /3-phase TP [mm] -/15 -/131 -/1 1-/3-phase TPE [mm] -/- -/- -/- H [mm] M M1 M1 M1 - and -pole TP and TPD pumps from 1.1 to 9 kw are fitted with motors as standard. 77

78 Performance curves DN -pole, PN 1 TP -XXX/ H -3/ TP, TPE Hz Q [m³/h] -3/ 3 Q [m³/h] NPSH -3/ Eta [%] Q [m³/h] -3/ 3 Q [m³/h] Q [l/s] 1 3 v [m/s] TM3 5 7

79 Technical data DN -pole, PN 1 P Rp 1/ H1 H D1 B1 B L1 H M AF AE C5 C1 TM Technical data TP -3/ TPD - TPE - TPED - Series 3 1-phase TP - IEC size 3-phase TP 1-phase TPE - 3-phase TPE - 1-/3-phase TP* -/55 1-/3-phase TPE -/- PN PN 1 T min ; T max [ C] [-5;1] D1 [mm] 1-/3-phase TP [mm] -/95 1-/3-phase TPE [mm] -/- 1-/3-phase TP [mm] -/39 1-/3-phase TPE [mm] -/- AE 1-/3-phase TPE [mm] - AF 1-/3-phase TPE [mm] - P [mm] 5 B1** [mm] 3/- B** [mm] 313/- B3 [mm] - ** TP [mm] 39/- TPE [mm] -/- C1** [mm] /- C5** [mm] /- C [mm] - L1 [mm] H1 [mm] 5 H [mm] 3 1-/3-phase TP [mm] -/1 1-/3-phase TPE [mm] -/- H [mm] M M1 - and -pole TP and TPD pumps from 1.1 to 9 kw are fitted with motors as standard. 79

80 Performance curves DN -pole, PN TP -XXX/ H 3 3-3/ -3/ -/ TP Hz H / -5/ TP Hz -3/ Q [m³/h] -/ -3/ -3/ 3 Q [m³/h] NPSH Q [m³/h] 3 7 Q [m³/h] NPSH -3/ -5/ -57/ Eta [%] Q [m³/h] -/ -3/ -3/ 3 Q [m³/h] Eta 3 7 Q [m³/h] [%] / -57/ -3/ Q [m³/h] 1 Q [l/s] v [m/s] TM 1 Q [l/s] v [m/s] TM 5

81 Technical data DN -pole, PN P D1D Rp 3/ L3 L1 H1 H L D1S C C Rp 3/ C C7 ø B B9 B1 B B7 TM 39 3 Technical data TP -/ -3/ -3/ -3/ -5/ -57/ TPD TPE TPED Series 1-phase TP IEC size 3-phase TP L 5 S 5 M M S M 1-phase TPE phase TPE PN T min ; T max [ C] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] [-5;1] D1 D /D1 S [mm] / / / / / / [mm] [mm] P [mm] B1 [mm] B [mm] [mm] B7 [mm] B [mm] B9 [mm] C [mm] C7 [mm] C [mm] Ø [mm] L1 [mm] L [mm] L3 [mm] H1 [mm] H [mm] [mm] and -pole TP and TPD pumps from 1.1 to 9 kw are fitted with motors as standard. 1

82 Performance curves DN -pole, PN TP -XXX/ H / -53/ -/ TP Hz 15 Q [m³/h] 1 -/ -5/ -53/ Q [m³/h] NPSH Eta [%] Q [m³/h] -/ -53/ -5/ Q [m³/h] 3 Q [l/s] v [m/s] TM

83 Technical data DN -pole, PN P D1D Rp 3/ L3 L1 H1 H L D1S C C Rp 3/ C C7 ø B B9 B1 B B7 TM 39 Technical data TP -/ -53/ -5/ TPD TPE TPED Series 1-phase TP IEC size 3-phase TP M 315 S 315 M 1-phase TPE phase TPE PN T min ; T max [ C] [-5;1] [-5;1] [-5;1] D1 D /D1 S [mm] /3 /3 /3 [mm] 555 [mm] P [mm] 5 B1 [mm] B [mm] [mm] B7 [mm] B [mm] B9 [mm] C [mm] C7 [mm] C [mm] Ø [mm] L1 [mm] L [mm] L3 [mm] H1 [mm] H [mm] [mm] and -pole TP and TPD pumps from 1.1 to 9 kw are fitted with motors as standard. 3

84 Performance curves DN -pole, PN 5 TP, -pole, PN 5 TP -XXX/ H / -1/ -1/ -/ TP Hz H / -/ -17/ -15/ -1/ TP Hz Q [m³/h] -13/ -1/ -1/ -/ Q [m³/h] -17/ -15/ -1/ -3/ -/ Q [m³/h] NPSH Q [m³/h] NPSH Eta [%] Q [m³/h] Eta [%] Q [m³/h] / -1/ -1/ -/ / -/ -17/ -15/ -1/ Q [m³/h] Q [m³/h] Q [l/s] 1 v [m/s] TM 53 Q [l/s] 1 v [m/s] TTM 5

85 Technical data DN -pole, PN 5 Rp 1/ P H D1D Rp 1/ L1 H1 D1S B B9 B C C9 ø C3 B5 B1 B B7 TM 3 Technical data TP -/ -1/ -1/ -13/ -1/ -15/ -17/ -/ -3/ TPD TPE TPED Series 1-phase TP IEC size 3-phase TP S M 315 S 315 M 315 S 315 M 315 L 315 L phase TPE phase TPE PN T min ; T max [ C] [;1] [;1] [;1] [;1] [;1] [;1] [;1] [;1] [;1] D1 D /D1 S [mm] /15 /15 /15 /15 /15 /15 /15 /15 /15 [mm] [mm] P [mm] 5 5 B1 [mm] B [mm] [mm] B5 [mm] B [mm] B7 [mm] B [mm] B9 [mm] C3 [mm] C [mm] C9 [mm] Ø [mm] L1 [mm] H1 [mm] H [mm] [mm] and -pole TP and TPD pumps from 1.1 to 9 kw are fitted with motors as standard. 5

86 Performance curves DN -pole, PN 5 TP, -pole, PN 5 TP -XXX/ H 3 3-3/ -33/ TP Hz H 55-59/ -53/ TP Hz -/ -/ 5 -/ -/ Q [m³/h] -/ -/ -3/ -33/ Q [m³/h] NPSH Q [m³/h] Q [m³/h] NPSH -59/ -/ -/ -53/ Eta [%] Q [m³/h] -33/ -/ -/ -3/ Q [m³/h] 3 Q [l/s] v [m/s] TM 5 Eta [%] Q [m³/h] -/ -/ -53/ -59/ Q [m³/h] 3 Q [l/s] v [m/s] TM 59

87 Technical data DN -pole, PN 5 Rp 1/ P H D1D Rp 1/ L1 H1 D1S B B9 B C C9 ø C3 B5 B1 B B7 TM 3 Technical data TP -/ -/ -33/ -3/ -/ -/ -53/ -59/ TPD TPE TPED Series 1-phase TP IEC size 3-phase TP 13 M 1 M 1 L 1 M 1 M 1 L L 5 S 1-phase TPE phase TPE PN T min ; T max [ C] [;1] [;1] [;1] [;1] [;1] [;1] [;1] [;1] D1 D /D1 S [mm] /15 /15 /15 /15 /15 /15 /15 /15 [mm] [mm] P [mm] 5 B1 [mm] B [mm] [mm] B5 [mm] B [mm] B7 [mm] B [mm] B9 [mm] C3 [mm] C [mm] C9 [mm] Ø [mm] L1 [mm] H1 [mm] H [mm] [mm] and -pole TP and TPD pumps from 1.1 to 9 kw are fitted with motors as standard. 7

88 Performance curves DN 15 -pole, PN 5 TP 15-XXX/ H / -3/ -7/ -/ TP 15 Hz 1 1 Q [m³/h] -7/ -/ -3/ -37/ 1 1 Q [m³/h] NPSH 5 3 H / -57/ -/ -/ -3/ TP 15 Hz Q [m³/h] -3/ -/ -/ -57/ -/ Q [m³/h] NPSH 1 Eta [%] Q [m³/h] -7/ -37/ -3/ -/ 1 1 Q [m³/h] Eta [%] Q [m³/h] -3/ -/ -/ -57/ -/ Q [m³/h] Q [l/s] v [m/s] TM Q [l/s] v [m/s] TM 1

89 Technical data DN 15 -pole, PN 5 Rp 1/ P H D1D Rp 1/ L1 H1 D1S B B9 B C C9 ø C3 B5 B1 B B7 TM 3 Technical data TP 15 -/ -7/ -3/ -37/ -3/ -/ -/ -57/ -/ TPD TPE TPED Series 1-phase TP IEC size 3-phase TP 1 L 1 M 1 L L 1 L L 5 S 5 M M 1-phase TPE phase TPE PN T min ; T max [ C] [;1] [;1] [;1] [;1] [;1] [;1] [;1] [;1] [;1] D1 D /D1 S [mm] 15/1 15/1 15/1 15/1 15/1 15/1 15/1 15/1 15/1 [mm] [mm] P [mm] B1 [mm] B [mm] [mm] B5 [mm] B [mm] B7 [mm] B [mm] B9 [mm] C3 [mm] C [mm] C9 [mm] Ø [mm] L1 [mm] H1 [mm] H [mm] [mm] and -pole TP and TPD pumps from 1.1 to 9 kw are fitted with motors as standard. 9

90 Performance curves DN 1 -pole, PN 5 TP 1-XXX/ H / -/ -7/ -9/ -/ -37/ -33/ TP 1 Hz Q [m³/h] -93/ -/ -7/ -9/ -/ -37/ -33/ Q [m³/h] NPSH Eta [%] Q [m³/h] -37/ -33/ -9/ -/ -/ -7/ -93/ Q [m³/h] 1 1Q [l/s] v [m/s] M 3 9

91 Technical data DN 1 -pole, PN 5 Rp 1/ P H D1D Rp 1/ L1 H1 D1S B B9 B C C9 ø C3 B5 B1 B B7 TM 3 Technical data TP 1-33/ -37/ -/ -9/ -7/ -/ -93/ TPD TPE TPED Series 1-phase TP IEC size 3-phase TP L 5 S 5 M M M 315 S 315 M 1-phase TPE phase TPE PN T min ; T max [ C] [;1] [;1] [;1] [;1] [;1] [;1] [;1] D1 D /D1 S [mm] 1/ 1/ 1/ 1/ 1/ 1/ 1/ [mm] [mm] P [mm] B1 [mm] B [mm] [mm] B5 [mm] B [mm] B7 [mm] B [mm] B9 [mm] C3 [mm] C [mm] C9 [mm] Ø [mm] L1 [mm] H1 [mm] H [mm] [mm] and -pole TP and TPD pumps from 1.1 to 9 kw are fitted with motors as standard. 91

92 Performance curves DN -pole, PN 5 TP -XXX/ H / -5/ -37/ -3/ TP Hz H / -/ -7/ -7/ TP Hz Q [m³/h] -5/ -5/ Q [m³/h] -93/ -/ -7/ -7/ 3-37/ -3/ 3 7 Q [m³/h] NPSH Eta [%] Q [m³/h] -5/ -37/ -3/ -5/ 3 7 Q [m³/h] 3 7 Q [m³/h] NPSH 1 Eta [%] Q [m³/h] -7/ -7/ -/ -93/ 3 7 Q [m³/h] 1 Q [l/s] v [m/s] TM 1 Q [l/s] v [m/s] TM 5 9

93 Technical data DN -pole, PN 5 Rp 1/ P H D1D Rp 1/ L1 H1 D1S B B9 B C C9 ø C3 B5 B1 B B7 TM 3 Technical data TP -3/ -37/ -5/ -5/ -7/ -7/ -/ -93/ TPD TPE TPED Series 1-phase TP IEC size 3-phase TP 5 M M S M 315 S 315 M 315 M 315 L 1-phase TPE phase TPE PN T min ; T max [ C] [;1] [;1] [;1] [;1] [;1] [;1] [;1] [;1] D1 D /D1 S [mm] / / / / / / / / [mm] [mm] P [mm] B1 [mm] B [mm] [mm] B5 [mm] B [mm] B7 [mm] B [mm] B9 [mm] C3 [mm] C [mm] C9 [mm] Ø [mm] L1 [mm] H1 [mm] H [mm] [mm] and -pole TP and TPD pumps from 1.1 to 9 kw are fitted with motors as standard. 93

94 Performance curves DN -pole, PN 5 TP -XXX/ H 55-5/ -/ TP Hz H 1 9 -/ -9/ TP Hz 5-3/ 7 -/ -7/ Q [m³/h] -3/ -5/ -/ Q [m³/h] -7/ -9/ -/ -/ Q [m³/h] NPSH Eta [%] Q [m³/h] -3/ -/ -5/ Q [m³/h] Q [m³/h] NPSH Eta [%] Q [m³/h] -7/ -9/ -/ -/ Q [m³/h] 3 Q [l/s] v [m/s] TM 3 Q [l/s] v [m/s] TM 7 9

95 Technical data DN -pole, PN 5 Rp 1/ P H D1D Rp 1/ L1 H1 D1S B B9 B C C9 ø C3 B5 B1 B B7 TM 3 Technical data TP -3/ -/ -5/ -7/ -/ -9/ -/ TPD TPE TPED Series 1-phase TP IEC size 3-phase TP M 315 S 315 M 315 M 315 L phase TPE phase TPE PN T min ; T max [ C] [;1] [;1] [;1] [;1] [;1] [;1] [;1] D1 D /D1 S [mm] /3 /3 /3 /3 /3 /3 /3 [mm] [mm] P [mm] 5 B1 [mm] B [mm] [mm] B5 [mm] B [mm] B7 [mm] B [mm] B9 [mm] C3 [mm] C [mm] C9 [mm] Ø [mm] L1 [mm] H1 [mm] H [mm] [mm] and -pole TP and TPD pumps from 1.1 to 9 kw are fitted with motors as standard. 95

96 Weights and shipping volume TP, TPD, TPE TP, TPD, TPE, -pole, PN //1 Connection Weights Shipping Pump type Net [kg] Gross [kg] volume [m 3 ] D1 D D1 S TP/TPD TPE TP/TPD TPE TP/TPD TPE TP 3-/ DN 3 DN TP 3-1/ DN 3 DN TP 3-/ DN 3 DN TP 3-/ DN 3 DN TP 3-33/ DN 3 DN TP, TPD 3-3/ DN 3 DN 3 5.5/ / / /- TP, TPD 3-3/ DN 3 DN 3 9./ / /.5.17/- TP, TPD 3-/ DN 3 DN 3 7./ / /.5.17/- TP, TPD 3-5/ DN 3 DN 3 9.7/ / /.5.17/- TP, TPD 3-/ DN 3 DN / / /.5.17/- TP, TPD 3-/ DN 3 DN 3 1./ / /.7 - TP -/ DN DN TP -1/ DN DN TP -/ DN DN TP -7/ DN DN TP -33/ DN DN TP -39/ DN DN TP, TPD -37/ DN DN 7./ / /.7.17/- TP, TPD -/ DN DN 9./ / / /- TP, TPD -5/ DN DN 91./ / / /- TP, TPD -7/ DN DN 139./ / /.7.7/- TP, TPD -/ DN DN 151./ / /.7.7/- TP, TPD -93/ DN DN 11./ / /.7.7/- TP -/ DN DN TP -1/ DN DN TP -/ DN DN TP, TPD -/ DN DN 53./ /1...1/.5.1/- TP, TPD -3/ DN DN 5.1/ / /.5.1/- TP, TPD -3/ DN DN 71.1/ / /.5.1/- TP, TPD -/ DN DN 5./ / /.5.1/- TP, TPD -/ DN DN 99./ / /.51.17/- TP, TPD -5/ DN DN 17./ /33..7/.7.7/- TP, TPD -7/ DN DN 15./ / /.7.7/- TP, TPD -79/ DN DN 1./ /375..7/.7.7/- TP, TPD -/ DN DN 197./ / /1.5.7/- TP, TPD -/ DN DN.3/ / /1.5 TP 5-/ DN 5 DN /1.5 - TP 5-1/ DN 5 DN TP 5-/ DN 5 DN TP, TPD 5-/ DN 5 DN 5 9./ /11...1/.5.1/- TP, TPD 5-/ DN 5 DN 5 7./ / /.3.1/- TP, TPD 5-3/ DN 5 DN 5./ / /.3.1/- TP, TPD 5-39/ DN 5 DN 5 9.5/ /199..1/.5.1/- TP, TPD 5-/ DN 5 DN 5 1.9/ / /.7.7/- TP, TPD 5-5/ DN 5 DN 5 1./ /31..7/.7.7/- TP, TPD 5-3/ DN 5 DN / / /.7.7/- TP, TPD 5-7/ DN 5 DN / /. -.7/1.5 - TP, TPD 5-9/ DN 5 DN 5 9./ /1. -.7/1.5 - TP, TPD 5-/ DN 5 DN 5 3.7/ /. -.7/1.5 - TP -1/ DN DN TP, TPD -/ DN DN 7./ / /.5.7/- TP, TPD -/ DN DN 93./ / /.5.7/- TP, TPD -9/ DN DN 95./ / /.5.7/- TP, TPD -33/ DN DN 151./ / /1.5.7/- 9

97 Weights and shipping volume TP, TPD, TPE Pump type TP, TPD -/ DN DN 1./ / /1.5.7/- TP, TPD -/ DN DN 17./ / /1.5.7/- TP, TPD -53/ DN DN 7./9..3./ /1.5.7/- TP, TPD -/ DN DN 3./ /3. -.7/1.5 - TP, TPD -7/ DN DN 31./ /. -.7/1.5 - TP, TPD -3/ DN DN 1./ / /1.5.7/- TP, TPD -3/ DN DN 155./ / /1.5.7/- TP, TPD -37/ DN DN 1./ / /1.5.99/- TP, TPD -3/ DN DN./ / /1.5.7/- TP, TPD -3/ DN DN 3./ / /1.5.99/- TP, TPD -53/ DN DN 33./ / /1. TP, TPD -3/ DN DN 35./ / /1. TP, TPD -7/ DN DN 3./ / /1. The dimension before the slash applies to the single-head pump and the dimension after the slash applies to the twin-head pump. TP, TPD, TPE, -pole, PN //1 Connection Weights Shipping volume [m 3 ] D1 D D1 S Net [kg] Gross [kg] TP/TPD TPE TP/TPD TPE TP/TPD TPE Pump type Connection Weights Shipping D1 volume [m 3 D D1 S Net [kg] Gross [kg] ] TP/TPD TPE TP/TPD TPE TP/TPD TPE TP 3-/ DN 3 DN TP 3-/ DN 3 DN TP, TPD 3-1/ DN 3 DN 3./ / / TP, TPD 3-1/ DN 3 DN 3 7.9/ / / TP, TPD 3-19/ DN 3 DN 3 53./ / / /- TP -/ DN DN TP -/ DN DN TP, TPD -1/ DN DN 7./ / /.5 - TP, TPD -1/ DN DN 53./ / /.5.17/- TP, TPD -19/ DN DN 5.1/1. 5./ /.5.17/- TP, TPD -/ DN DN 3./ / /.5.17/- TP -/ DN DN TP -/ DN DN TP, TPD -1/ DN DN 55.9/ / /.97 - TP, TPD -1/ DN DN.1/ / /.51.17/- TP, TPD -1/ DN DN.3/ / /.51.17/- TP, TPD -19/ DN DN 71.1/ / /.51.17/- TP, TPD -/ DN DN 75.9/ / /.51.17/- TP, TPD -7/ DN DN./ / /.51.17/- TP, TPD -3/ DN DN 11.1/ / /.51.7/- TP 5-/ DN 5 DN TP 5-/ DN 5 DN TP, TPD 5-13/ DN 5 DN 5./ / /.5.17/- TP, TPD 5-1/ DN 5 DN 5 7.9/ / /.5.17/- TP, TPD 5-19/ DN 5 DN 5 77./ /1...17/.5.17/- TP, TPD 5-3/ DN 5 DN 5 1./..7./ /.5.17/- TP, TPD 5-3/ DN 5 DN / / /.5.7/- TP, TPD 5-33/ DN 5 DN 5 1.1/ /. 1.7/.7 - TP -/ DN DN TP -/ DN DN TP, TPD -1/ DN DN 7./ / /.5.17/- TP, TPD -1/ DN DN 9./ / /.51.7/- TP, TPD -17/ DN DN 3./ / /.7.7/- TP, TPD -3/ DN DN 1./ / /1.5.99/- TP, TPD -/ DN DN 19./ / /1.5.99/- TP, TPD -3/ DN DN 5./ / /1.5.99/- TP, TPD -/ DN DN./7..5./ /1.5.99/- TP, TPD -/ DN DN 9./ / /1.5.99/- 97

98 Weights and shipping volume TP, TPD, TPE Pump type TP, TPD -5/ DN DN./ / /1.5.99/- TP -/ DN DN TP -/ DN DN TP, TPD -/ DN DN 1./ / /1.5.99/- TP, TPD -13/ DN DN 1./ / /1.5.99/- TP, TPD -17/ DN DN 157./ / /1.5.99/- TP, TPD -/ DN DN 3./ / /1.5.99/- TP, TPD -/ DN DN./ / /1.5.99/- TP, TPD -9/ DN DN 75./ / /1.5.99/- TP, TPD -3/ DN DN 3./ / /1.5.99/- TP, TPD -39/ DN DN 315./ / /1.5.99/- TP, TPD -7/ DN DN 15./. - 3./ /1. - TP, TPD 15-13/ DN 15 DN 15 3./ / /1.5.99/- TP, TPD 15-1/ DN 15 DN / / /1.5.99/- TP, TPD 15-/ DN 15 DN 15./ / /1.5.99/- TP, TPD 15-/ DN 15 DN / / /1.5.99/- TP, TPD 15-3/ DN 15 DN / / /1..99/- TP, TPD 15-3/ DN 15 DN 15 1./ / /1..99/- TP, TPD 15-3/ DN 15 DN /3. -./ /1. - TP, TPD 15-9/ DN 15 DN 15 9./ / /1. - TP, TPD 1-1/ DN 1 DN 1 31./ / /1.5.99/- TP, TPD 1-/ DN 1 DN / / /1..99/- TP, TPD 1-/ DN 1 DN 1 31./ / /1..99/- TP, TPD 1-3/ DN 1 DN 1./ / /1. TP 1-3/ DN 1 DN TP 1-3/ DN 1 DN TP 1-/ DN 1 DN TP 1-/ DN 1 DN TP 1-9/ DN 1 DN TP 1-5/ DN 1 DN TP -7/ DN DN TP -/ DN DN TP -9/ DN DN TP -3/ DN DN TP -33/ DN DN TP -3/ DN DN TP -3/ DN DN TP -3/ DN DN TP -5/ DN DN TP -57/ DN DN TP -/ DN DN TP -53/ DN DN TP -5/ DN DN The dimension before the slash applies to the single-head pump and the dimension after the slash applies to the twin-head pump. TP, -pole, PN 5 Connection Weights Shipping D1 volume [m 3 D D1 S Net [kg] Gross [kg] ] TP/TPD TPE TP/TPD TPE TP/TPD TPE Pump type Connection Weights Shipping D1 volume [m 3 D D1 S Net [kg] Gross [kg] ] TP -/ DN DN TP -1/ DN DN TP -1/ DN DN TP -13/ DN DN TP -1/ DN DN TP -15/ DN DN TP -17/ DN DN TP -/ DN DN TP -3/ DN DN

99 Weights and shipping volume TP, TPD, TPE TP, -pole, PN 5 Pump type Connection Weights Shipping D1 volume [m 3 D D1 S Net [kg] Gross [kg] ] TP -/ DN DN TP -/ DN DN TP -33/ DN DN TP -3/ DN DN TP -/ DN DN TP -/ DN DN TP -53/ DN DN TP -59/ DN DN TP 15-/ DN 15 DN TP 15-7/ DN 15 DN TP 15-3/ DN 15 DN TP 15-37/ DN 15 DN TP 15-3/ DN 15 DN TP 15-/ DN 15 DN TP 15-/ DN 15 DN TP 15-57/ DN 15 DN TP 15-/ DN 15 DN TP 1-33/ DN 1 DN TP 1-37/ DN 1 DN TP 1-/ DN 1 DN TP 1-9/ DN 1 DN TP 1-7/ DN 1 DN TP 1-/ DN 1 DN TP 1-93/ DN 1 DN TP -3/ DN DN TP -37/ DN DN TP -5/ DN DN TP -5/ DN DN TP -7/ DN DN TP -7/ DN DN TP -/ DN DN TP -93/ DN DN TP -3/ DN DN TP -/ DN DN TP -5/ DN DN TP -7/ DN DN TP -/ DN DN TP -9/ DN DN TP -/ DN DN

100 Accessories TP, TPD, TPE Counter flanges Cast iron pumps A flange kit consists of two steel flanges, two gaskets of asbestos-free material IT, and the requisite number of bolts. Counter flange Pump type Description Rated pressure Pipework connection Product number Rp 1¼ ø19 Threaded bar, EN 9- Rp 1¼ Threaded For welding ø7 ø ø1 TM3 7 5 TP, TPE 3 TPD 3 For welding bar, EN 9-3 mm, nominal 5397 Threaded bar, EN 9- Rp 1½ Rp 1½ ø19 TP, TPE TPD For welding bar, EN 9- mm, nominal 5397 Threaded For welding ø ø1 ø1 TM Threaded 1 bar, EN 9- Rp 1½ For welding 1 bar, EN 9- mm, nominal 5397 Threaded bar, EN 9- Rp 591 Rp ø19 TP, TPE TPD For welding bar, EN 9- mm, nominal 59 Threaded For welding ø ø15 ø15 TM3 5 Threaded 1 bar, EN 9- Rp 591 Rp ½ ø19 For welding 1 bar, EN 9- mm, nominal 59 TP, TPE 5 TPD 5 Threaded For welding ø1 ø15 ø15 TM3 1 5 Threaded bar, EN 9- Rp ½ 5591 For welding bar, EN 9-5 mm, nominal 559

101 Accessories TP, TPD, TPE Counter flange Pump type Description Rated pressure Pipework connection Product number Threaded bar, EN 9- Rp For welding bar, EN 9- mm, nominal 5991 Rp 3 ø19 Threaded bar, EN 9- Rp 3 59 Threaded For welding ø13 ø1 ø TP, TPE TPD For welding bar, EN 9- mm, nominal 591 TM3 5 Threaded 1 bar, EN 9- Rp 3 59 For welding 1 bar, EN 9- mm, nominal 591 Threaded bar, EN 9- Rp For welding bar, EN 9- mm, nominal 5799 Rp ø19 Threaded bar, EN 9- Rp 5791 Threaded For welding ø15 ø1 ø TP, TPE TPD For welding bar, EN 9- mm, nominal 579 TM3 3 5 Threaded 1 bar, EN 9- Rp 5791 For welding 1 bar, EN 9- mm, nominal 579 1

102 Accessories TP, TPD, TPE Bronze pumps A flange kit consists of two bronze flanges, two gaskets of asbestos-free material IT, and the requisite number of bolts. Counter flange Pump type Description Rated pressure Pipework connection Product number Rp 1¼ ø19 Threaded bar, EN 9- Rp 1¼ 979 Threaded For welding ø7 ø ø1 TM3 7 5 TP, TPE 3 B For welding bar, EN 9-3 mm, nominal 973 Threaded bar, EN 9- Rp 1½ Rp 1½ ø19 For welding bar, EN 9- mm, nominal TP, TPE B Threaded For welding ø ø1 ø1 TM Threaded 1 bar, EN 9- Rp 1½ For welding 1 bar, EN 9- mm, nominal Rp ø19 Threaded Rp ½ For welding ø19 ø ø15 ø15 TM3 5 TP, TPE B Threaded bar, EN 9- Rp 5911 Threaded For welding ø1 ø15 ø15 TM3 1 5 For welding bar, EN 9- mm, nominal 591 Threaded bar, EN 9- Rp ½ Rp 3 ø19 TP, TPE 5 B For welding bar, EN 9-5 mm, nominal 5591 Threaded For welding ø13 ø1 ø TM3 5 TP, TPE B Threaded bar, EN 9- Rp For welding bar, EN 9- mm, nominal 59911

103 Accessories TP, TPD, TPE Base plates TP, TPE series 3 TP Series Pump type TP 3 TP TP TP 5-/, 5-1/, 5-/ TP 5-/, 5-/ TP TP Hexagon head screws Product no. x M1 x mm x M1 x 3 mm 9591 Pump type TP 1 TP Drawing Hexagon head screws Product number M1 x 35 mm 9351 Product number TP, TPE Series 3 Pump type TP, TPE 3 TP, TPE TP, TPE TP, TPE 5 TP, TPE TP, TPE TP, TPE 15 TP, TPE 1 Hexagon head screws Product no. x M1 x 3 mm 31 TM Drawing Product number xø xø1 xø1 1 1 xø1 xø1 TM TPD Series 3 Pump type TPD 3 TPD TPD TPD 5 Hexagon head screws Product no. x M1 x 3 mm 9931 Drawing Product number xø xø1 TM 533 Note: Base plates are supplied as standard with TP/TPD pumps with 11 kw motors and above. 3

104 Accessories TP, TPD, TPE Blanking flanges Normally used with twin-head pumps. TM TPD -pole Pump type TPD 3-3/ TPD 3-3/ TPD 3-/ TPD 3-5/ TPD 3-/ TPD 3-/ TPD -37/ TPD -/ TPD -5/ TPD -7/ TPD -/ TPD -93/ TPD -/ TPD -3/ TPD -3/ TPD -/ TPD -/ TPD -5/ TPD -7/ TPD -79/ TPD -/ TPD -/ TPD 5-/ TPD 5-/ TPD 5-3/ TPD 5-39/ TPD 5-/ TPD 5-5/ TPD 5-3/ TPD 5-7/ TPD 5-9/ TPD 5-/ TPD -/ TPD -/ TPD -9/ TPD -33/ TPD -/ TPD -/ TPD -53/

105 Accessories TP, TPD, TPE Pump type TPD -/ TPD -7/ TPD -3/ TPD -3/ TPD -37/ TPD -3/ TPD -3/ TPD -53/ TPD -3/ TPD -7/ 5

106 Accessories TP, TPD, TPE TPD, TPED -pole Pump type TPD 3-1/ TPD 3-1/ TPD 3-19/ TPD -1/ TPD -1/ TPD -19/ TPD -/ TPD -1/ TPD -1/ TPD -1/ TPD -19/ TPD -/ TPD -7/ TPD -3/ TPD 5-13/ TPD 5-1/ TPD 5-19/ TPD 5-3/ TPD 5-3/ TPD 5-33/ TPD -1/ TPD -1/ TPD -17/ TPD -3/ TPD -/ TPD -3/ TPD -/ TPD -/ TPD -5/ TPD -/ TPD -13/ TPD -17/ TPD -/ TPD -/ TPD -9/ TPD -3/ TPD -39/ TPD -7/ TPD 15-13/ TPD 15-1/ TPD 15-/ TPD 15-/ TPD 15-3/ TPD 15-3/ TPD 15-3/ TPD 15-9/ TPD 1-1/ TPD 1-/ TPD 1-/ TPD 1-3/

107 Accessories TP, TPD, TPE Insulating kits Insulating kits are only available for TP Series pumps. An insulating kit consists of two or three insulating covers made of expanded polypropylene (EPP). The insulating kit is tailored to the individual pump model and has an insulating thickness corresponding to the nominal diameter of the pump. The thermal conductivity of EPP is very low (. W/ m C), i.e. the insulating property is very good. The insulating kit encloses the entire pump housing. Fig. 7 Insulating kit TM 95 9 Product numbers of insulating kits Single-head TP Series pumps Pump type Product no. TP 3-/ 95 TP 3-/ 9573 TP 3-/ 95 TP 3-1/ 95 TP 3-/ 9751 TP 3-/ 9751 TP 3-33/ 9751 TP -/ 957 TP -/ 957 TP -/ 9575 TP -1/ 9577 TP -/ 957 TP -7/ 975 TP -33/ 975 TP -39/ 975 TP -/ 9579 TP -/ 951 TP -/ 95 TP -1/ 95 TP -/ 953 TP 5-/ 95 TP 5-/ 95 TP 5-/ 955 TP 5-1/ 957 TP 5-/ 95 TP -/ 959 TP -/ 959 TP -1/ 9591 TP -/ 959 TP -/ 959 7

108 Accessories TP, TPD, TPE Sensors Accessory Type Supplier Measuring range Product number Flowmeter Flowmeter Flowmeter Flowmeter Note: All sensors have - ma output signal. Sensors for boosting applications Sensors for circulation applications SITRANS F M MAGFLO MAG 5 W SITRANS F M MAGFLO MAG 5 W SITRANS F M MAGFLO MAG 5 W SITRANS F M MAGFLO MAG 5 W Siemens Siemens Siemens Siemens 1-5 m 3 /h (DN 5) 3 - m 3 /h (DN ) - 3 m 3 /h (DN 5) - 75 m 3 /h (DN ) ID5 ID ID7 ID Temperature sensor TTA () 5 Carlo Gavazzi C to +5 C Temperature sensor TTA (-5) 5 Carlo Gavazzi 5 C to +5 C 9319 Temperature sensor TTA () Carlo Gavazzi C to + C 9359 Temperature sensor TTA () 1 Carlo Gavazzi C to +1 C Accessory for temperature sensor. All with ½ RG connection. Temperature sensor, ambient temperature Protecting tube ø9 x mm Carlo Gavazzi 931 Protecting tube ø9 x mm Carlo Gavazzi 93 Cutting ring bush Carlo Gavazzi 933 WR 5 tmg (DK: Plesner) C to + C ID95 Differential temperature sensor ETSD Honsberg C to + C 993 Differential temperature sensor ETSD Honsberg C to + C 9933 Danfoss pressure sensor kit Pressure range Product number Connection: G ½ A (DIN 1 - Bkt) Electrical connection: plug (DIN 3) Pressure sensor type MBS 3, with m screened cable Connection: G ¼ A (DIN 1 - Bkt) 5 cable clips (black) Fitting instructions PT (1) -.5 bar bar bar bar bar bar bar 51 - bar bar 51-1 bar 513 Grundfos differential pressure sensor, DPI Pressure range Product number 1 sensor incl..9 m screened cable (7/1" connections) 1 original DPI bracket (for wall mounting) 1 Grundfos bracket (for mounting on motor) M screws for mounting of sensor on bracket 1 M screw (self-cutting) for mounting on MGE 9/ 1 M screw (self-cutting) for mounting on MGE 11/13 1 M screw (self-cutting) for mounting on MMGE 1 1 M1 screw (self-cutting) for mounting on MMGE 1 3 capillary tubes (short/long) fittings (1/" - 7/1") 5 cable clips (black) Installation and operating instructions Service kit instruction -. bar bar bar bar bar bar bar 9115 Select the differential pressure sensor so that the maximum pressure of the sensor is higher than the maximum differential pressure of the pump.

109 Accessories TP, TPD, TPE Potentiometer Potentiometer for setpoint setting and start/stop of the pump. Product External potentiometer with cabinet for wall mounting. Product number 5 R R is used for wireless communication. Communication takes place by means of infrared light. Product Product number R 5333 G-LON interface The G-LON interface is used in connection with data transmission between a Locally Operating Network (LON) and electronically controlled Grundfos pumps applying the Grundfos bus-protocol GENIbus. Product Product number G-LON interface 57 EMC filter MMGE motors comply with the limits of EN 1-3 (emission) for use in second environments (industrial areas), unrestricted distribution, corresponding to CISPR11, group, class A. If MMGE motors (7.5- kw) are equipped with an external EMC filter, they comply with the limits for first environments (residential areas), unrestricted distribution, corresponding to CISPR11, group 1, class B. TM Fig. EMC filter The EMC filter is available as a complete kit ready for installation. EMC kit EMC filter in IP 5 aluminium cabinet Accessories for connection to motor terminal box: - 1 reducer from M x 1.5 to M3 x EMC nut M x EMC cable gland M3 x Installation and operating instructions Product number

110 Minimum inlet pressure - NPSH TP, TPD, TPE To ensure optimum and noiseless operation we recommend the minimum inlet pressure values shown on page 111 to 113. A minimum inlet pressure is required to avoid pressure drop that may cause cavitation. The minimum inlet pressure (P s ) in bar can be calculated using the following formula. Note: Calculation of the minimum inlet pressure should be based on the maximum required flow. c Ps NPSH Temp. [ C] P d [bar] p s ( NPSH R + H s ) ρ g -- ρ c p b + p d P s = Minimum inlet pressure in bar. NPSH R = The required Net Positive Suction Head in metres head. (To be read from the NPSH curve at the highest flow the pump will be delivering). H s = Safety margin = minimum.5 metres head. Note: A safety margin of.5 metres prevents pressure drop. r = Density of the pumped liquid measured in kg/m 3. g = Gravitational acceleration measured in m/ s. For estimated calculations use the value 9.1 m/s. c = Flow velocity of the pumped liquid at the pressure gauge. Insert the flow velocity as the unit [m/s]. (See individual curve charts from page 39). p b = Barometric pressure in bar. (Set the barometric pressure to.97 bar) Note: Only occasionally is the pressure as high as 1 bar; also this value is at sea level. P d = Vapour pressure in bar. (See Table 9 on page 1). Fig. 9 Minimum inlet pressure TM 91 - TM

111 Minimum inlet pressure - NPSH TP, TPD, TPE TP, TPD -pole, PN //1 Pump type p [bar] C C 9 C 1 C 1 C 1 C TP 3-/ TP 3-1/ TP 3-/ TP 3-/ TP 3-33/ TP, TPD 3-3/ TP, TPD 3-3/ TP, TPD 3-/ TP, TPD 3-5/ TP, TPD 3-/ TP, TPD 3-/ TP -/ TP -1/ TP -/ TP -7/ TP -33/ TP -39/ TP, TPD -37/ TP, TPD -/ TP, TPD -5/ TP, TPD -7/ TP, TPD -/ TP, TPD -93/ TP -/ TP -1/ TP -/ TP, TPD -/ TP, TPD -3/ TP, TPD -3/ TP, TPD -/ TP, TPD -/ TP, TPD -5/ TP, TPD -7/ TP, TPD -79/ TP, TPD -/ TP -/ TP 5-/ TP 5-1/ TP 5-/ TP, TPD 5-/ TP, TPD 5-/ TP, TPD 5-3/ TP, TPD 5-39/ TP, TPD 5-/ TP, TPD 5-5/ TP, TPD 5-3/ TP, TPD 5-7/ TP 5-9/ TP 5-/ Pump type p [bar] C C 9 C 1 C 1 C 1 C TP -1/ TP, TPD -/ TP, TPD -/ TP, TPD -9/ TP, TPD -33/ TP, TPD -/ TP, TPD -/ TP, TPD -53/ TP, TPD -/ TP, TPD -7/ TP, TPD -3/ TP, TPD -3/ TP, TPD -37/ TP, TPD -3/ TP, TPD -3/ TP, TPD -53/ TP, TPD -3/ TP, TPD -7/

112 Minimum inlet pressure - NPSH TP, TPD, TPE TP, TPD -pole, PN //1 Pump type p [bar] C C 9 C 1 C 1 C 1 C TP 3-/ TP 3-/ TP, TPD 3-1/ TP, TPD 3-1/ TP, TPD 3-19/ TP -/ TP -/ TP, TPD -1/ TP, TPD -1/ TP, TPD -19/ TP, TPD -/ TP -/ TP -/ TP, TPD -1/ TP, TPD -1/ TP, TPD -1/ TP, TPD -19/ TP, TPD -/ TP, TPD -7/ TP, TPD -3/ TP 5-/ TP 5-/ TP, TPD 5-13/ TP, TPD 5-1/ TP, TPD 5-19/ TP, TPD 5-3/ TP, TPD 5-3/ TP, TPD 5-33/ TP -/ TP -/ TP, TPD -1/ TP, TPD -1/ TP, TPD -17/ TP, TPD -3/ TP, TPD -/ TP, TPD -3/ TP, TPD -/ TP, TPD -/ TP, TPD -5/ TP -/ TP, TPD -/ TP, TPD -13/ TP, TPD -17/ TP, TPD -/ TP, TPD -/ TP, TPD -9/ TP, TPD -3/ TP, TPD -39/ TP, TPD -7/ TP -/ Pump type p [bar] C C 9 C 1 C 1 C 1 C TP, TPD 15-13/ TP, TPD 15-1/ TP, TPD 15-/ TP, TPD 15-/ TP, TPD 15-3/ TP, TPD 15-3/ TP, TPD 15-3/ TP, TPD 15-9/ TP, TPD 1-1/ TP, TPD 1-/ TP, TPD 1-/ TP, TPD 1-3/ TP 1-3/ TP 1-3/ TP 1-/ TP 1-/ TP 1-9/ TP 1-5/ TP -7/ TP -/ TP -9/ TP -3/ TP -33/ TP -3/ TP -3/ TP -3/ TP -5/ TP -57/ TP -/ TP -53/ TP -5/ TP Series, -pole, PN 5 Pump type p [bar] C C 9 C 1 C 1 C 1 C TP -/ TP -1/ TP -1/ TP -13/ TP -1/ TP -15/ TP -17/ TP -/ TP -3/

113 Minimum inlet pressure - NPSH TP, TPD, TPE TP Series, -pole, PN 5 Pump type p [bar] C C 9 C 1 C 1 C 1 C TP -/ TP -/ TP -33/ TP -3/ TP -/ TP -/ TP -53/ TP -59/ TP 15-/ TP 15-7/ TP 15-3/ TP 15-37/ TP 15-3/ TP 15-/ TP 15-/ TP 15-57/ TP 15-/ TP 1-33/ TP 1-37/ TP 1-/ TP 1-9/ TP 1-7/ TP 1-/ TP 1-93/ TP -/ TP -/ TP -3/ TP -3/ TP -37/ TP -5/ TP -5/ TP -7/ TP -7/ TP -/ TP -93/ TP -3/ TP -/ TP -5/ TP -7/ TP -/ TP -9/ TP -/

114 Further product documentation TP, TPD, TPE WebCAPS WebCAPS is a Web-based Computer Aided Product Selection program available on WebCAPS contains detailed information on more than 15, Grundfos products in more than languages. In WebCAPS, all information is divided into sections: Catalogue Literature Service Sizing Replacement C drawings. Catalogue This section is based on fields of application and pump types, and contains technical data curves (QH, Eta, P1,, etc) which can be adapted to the density and viscosity of the pumped liquid and show the number of pumps in operation product photos dimensional drawings wiring diagrams quotation texts, etc. Literature In this section you can access all the latest documents of a given pump, such as data booklets installation and operating instructions service documentation, such as Service kit catalogue and Service kit instructions quick guides product brochures, etc. Service This section contains an easy-to-use interactive service catalogue. Here you can find and identify service parts of both existing and discontinued Grundfos pumps. Furthermore, this section contains service videos showing you how to replace service parts. 11

115 1 Further product documentation TP, TPD, TPE Sizing This section is based on different fields of application and installation examples, and gives easy step-by-step instructions in how to select the most suitable and efficient pump for your installation carry out advanced calculations based on energy consumption, payback periods, load profiles, life cycle costs, etc. analyse your selected pump via the built-in life cycle cost tool determine the flow velocity in wastewater applications, etc. Replacement In this section you find a guide to selecting and comparing replacement data of an installed pump in order to replace the pump with a more efficient Grundfos pump. The section contains replacement data of a wide range of pumps produced by other manufacturers than Grundfos. Based on an easy step-by-step guide, you can compare Grundfos pumps with the one you have installed on your site. When you have specified the installed pump, the guide will suggest a number of Grundfos pumps which can improve both comfort and efficiency. C drawings In this section it is possible to download -dimensional (D) and 3-dimensional (3D) C drawings of most Grundfos pumps. These formats are available in WebCAPS: -dimensional drawings:.dxf, wireframe drawings.dwg, wireframe drawings. 3-dimensional drawings:.dwg, wireframe drawings (without surfaces).stp, solid drawings (with surfaces).eprt, E-drawings. WinCAPS WinCAPS is a Windows-based Computer Aided Product Selection program containing detailed information on more than 15, Grundfos products in more than languages. The program contains the same features and functions as WebCAPS, but is an ideal solution if no Internet connection is available. WinCAPS is available on CD-ROM and updated once a year. Fig. 3 WinCAPS CD-ROM 115