Lightstream Scroll kW ULTRACOMPACT II COMPACT AIR-COOLED CHILLERS WITH SCROLL COMPRESSORS

Transcription

1 Lightstream Scroll ULTRACOMPACT II COMPACT AIR-COOLED CHILLERS WITH SCROLL COMPRESSORS EXTREME EFFICIENCY WITH EER UP TO 3.29 OPTIONAL EVAPORATIVE PRE-COOLING MICROCHANNEL CONDENSING COILS COMPACT & LIGHTWEIGHT DESIGN kW AVAILABLE IN 4 FRAME SIZES, TOTAL 22 MODELS WITH A WIDE SELECTION OF OPTIONS AND ACCESSORIES SCROLL R410a EC-FANS MICROCHANNEL EVAPORATIVE HEAT RECOVERY

2 Scroll chillers with extreme efficiency LIGHTSTREAM SCROLL ULTRACOMPACT II AIR-COOLED CHILLER FAMILY PROVIDES CAPACITY-MATCHED COOLING, PRECISE THERMAL PARAMETERS, AND WATERFLOW % higher energy efficiency Ambient air temperature/humidity: 35ºC/50%rH Chilled water temperature: 7/12ºC These chillers display excellent performance, small footprint, and deliver best-in-class efficiency thank comprehensive engineering and first-grade components. The classic, time-approved design and built-in reliability of UltraCompact II make this machine a big league player in the field of process cooling, air conditioning, and refrigeration applications Average EER (kw/kw) 137% 110% 100% 1.0 UltraCompact II UltraCompact II Leading E VAP Standard competitors UltraCompact II Standard 10% ENERGY SAVINGS Compared to leading competitors with standard parameters: - ambient air temperature/humidity: 35ºC/50%rH - chilled water temperature: 7/12ºC EXTREME ENERGY EFFICIENCY WITH EER UP TO 3.29 COMPACT & LIGHTWEIGHT DESIGN INTELLIGENT HEAD PRESSURE CONTROL WATER TEMPERATURES OF UP TO -12ºC HEAT RECOVERY OPTIONS LOW OVERALL TCO UltraCompact II E VAP 37% ENERGY SAVINGS Compared to leading competitors with standard parameters: - ambient air temperature/humidity: 35ºC/50%rH - chilled water temperature: 7/12ºC UP TO 30% ENERGY SAVINGS ON COMPRESSORS CUTTING COMPRESSOR PEAK LOADS INCREASED COOLING CAPACITY - UP TO 8.5% EXPANDED OPERATING ENVELOPE WORKING CONDITIONS OF UP TO +55 C LOWER NOISE EMISSIONS

3 E VAP evaporative pre-cooling Effective way to reduce compressor hours E VAP evaporative pre-cooling system allows reducing the temperature of air delivered to condensers even in hot and humid environments and expands the operating envelope of the UltraCompact II chillers for up to +55 C while remaining at the same level of efficiency. Equipping UltraCompact II chillers with evaporative pads results in significant electricity savings of up to 30%. The evaporative media of E VAP is based on water retaining finned aluminium plates designed for maximum evaporation: the saturation efficiency reaches 90% and more at the air velocities of up to 2m/s. The internal geometry and special fin coating of evaporative media facilitate cleanliness of the evaporative media during the operation Condenser inlet air temperature (ºC) Pre-cooling efficiency at 35ºC dry bulb UltraCompact II E VAP convenient air-cooled chiller SAVINGS Relative humidity (%) In order to achieve maximum efficiency and minimal water usage, E VAP pre-cooling system can be equipped with a pumping station which includes the circulation pump, water treatment module and control system with state-of-the-art algorithms that monitor the ambient conditions and determine the operation modes, ensuring the E VAP system is active only when necessary. The fully automated water management system continuously monitors water quality, drains the system and refreshes the water when mineral levels reach certain values. Evaporative pads can be easily detached for maintenance and access the chiller's condensing coils for cleaning. Scroll compressors Proven performance and reliability The combination of an energy efficient motor and an optimized scroll wrap for refrigeration applications delivers high efficiency in UltraCompact II s fixed-speed compressors. Reliability is built into this compressor range, from the compliant scroll design and the engineered bearings to the simplified design. The thermal fault protection also contributes to excellent reliability. The customers of Lightstream UltraCompact II systems with fixed-speed compressors can benefit from proven reliability, low sound levels, low vibration and low operating and maintenance costs. Evaporators Brazed plate heat exchangers Brazing the stainless steel plates together eliminate the need for gaskets and thick frame plates, which makes the heat exchanger compact. The brazing material seals and holds the plates together at the contact points ensuring optimal heat transfer efficiency and pressure resistance. Using advanced design technologies and extensive verification guarantees the highest performance and longest possible service lifetime.

4 Powered by trendsetting technologies Optimum air flow for maximum efficiency Axial fans used in UltraCompact II design have outstanding characteristics in every respect, including performance and efficiency, weight, noise pollutions, and robustness. EC fan technology is an excellent solution for demand responsive cooling, and we equip UltraCompact II chillers with the latest EC motors which demonstrate impressive performance, low energy consumption, high torque, and durable design. EC fans with integrated electronic control can easily be varied in speed to match airflow demand. For the same air volume, they consume distinctly less energy than AC motors. The most common cause of fan motor failure and consequent capacity reduction of the chiller is overheating. EC fans of UltraCompact II chiller have temperature sensors built into the internal electronics package that act as a safety device in the case of overheating. Compared to AC motors, EC-type motors have longer service life due to lower winding temperatures resulting in lower wear and tare. Comprehensive corrosion protection measures have been taken that allow the fans to be used in almost all climatic applications with outstanding operating reliability. Microchannel condensers Enhanced heat transfer and low condensing temperature Microchannel condensers used in UltraCompact II design give a number of advantages, including higher heat transfer rate, low airside pressure drops, and closer approach temperatures. The end result is up to 40% higher energy efficiency in comparison to traditional fin/tube heat exchanger design. Smaller coil face, thin design, up to 50% less weight, and less refrigerant charge translate to lower system cost. Microchannel condensers used in UltraCompact II chiller range are true HVAC coils developed and optimized especially for refrigeration applications and enable remarkable low condensing temperatures. High-performance louvered fins Remote control The control hub of UltraCompact II chillers is a sophisticated controller and advanced software developed for efficient operation of scroll-based chillers. It manages and optimizes the chiller s performance, giving the complete control over the system for plant operator, either directly or remotely. Circulation pumps UltraCompact chillers can be equipped with high-quality single-stage single or twin pumps in inline design. The pumps feature reduced life cycle costs, optimized efficiency, and high standard of corrosion protection thanks to cataphoretic coating. Inverter-driven pumps are available optionally. Inverter-driven pumps have broad performance range, which enables them to perform efficiently under widely varied conditions and to meet a wide range of requirements.

5 Package, options and accessories Description General E VAP evaporative pre-cooling system E VAP pumping station Partial heat recovery system Total heat recovery system Waterside Pump (single/twin inline pumps - fixed-speed/inverter) Refrigerant side Electronic expansion valve(s) Service valves (compressor suction/discharge) Airside EC fans Electric and controls Electric panel heater Phase sequence relay Variable flow control MCHE e-coating Low noise design (grades 1-4) MCHE mesh guard -6 C brine kit Anti-vibration mounts -12 C brine kit Anti-vibration springs Water tank (F2/F3/F4 enclosure sizes) Pump coolant heater High-efficient refrigerant filters Pressure indication on high/low pressure sides AC fans BMS connectivity SNMP connectivity Energy monitoring Flowmeter Safety valves on high/low pressure sides Thermal insulation High-efficient fan diffusers Touch screen HMI Remote monitoring software Pumping group control system Standard feature Optional feature Frame sizes and model identification S 150 P 2 / 1 - E Compressors S Scroll Nominal capacity kw Evaporator type P Brazed plate Fans No. of fans Refrigerant circuits No. of refrigerant circuits Options E Evaporative pre-cooling system Frame size F1 F2 F3 F4 Length mm Width 1 mm Height 2 mm (1) without E VAP system (2) with standard fans/no diffusers F1 F2 F3 F4 Grooved connections We use grooved end connections because of their rigidity, flexibility, noise and vibration attenuation, and easy of installation and maintenance. The groove is made by cold forming or machining a groove into the end of a pipe. A gasket encompassed by the coupling housing is wrapped around the two grooved pipe ends, and the key sections of the coupling housing engage the grooves. The bolts and nuts are tightened with a socket wrench or impact wrench.

6 Technical Specs - Standard Lightstream Scroll S50 S75 S100 S125 S150 S175 S200 S225 S250 S275 S300 UltraCompact II P1/1 P1/1 P2/1 P2/1 P2/1 P3/1 P3/1 P3/1 P4/2 P4/2 P4/2 F1 F1 F2 F2 F2 F3 F3 F3 F4 F4 F4 Cooling capacity 1 kw EER Net weight kg Compressors Scroll Quantity Power input kw Absorbed current A Capacity steps Fans EC-type axial Quantity Airflow m³/h Power input kw Evaporator BPHE Water flow rate m³/h Pressure drop kpa Evaporation temp. C Refrigerant circuits R410a Quantity Charge kg (1) Coolant: Water 100%; Coolant temperatures: 7/12 C; Ambient temperature: 35 C Technical Specs - E VAP Lightstream Scroll S50 S75 S100 S125 S150 S175 S200 S225 S250 S275 S300 UltraCompact II P1/1-E P1/1-E P2/1-E P2/1-E P2/1-E P3/1-E P3/1-E P3/1-E P4/2-E P4/2-E P4/2-E F1 F1 F2 F2 F2 F3 F3 F3 F4 F4 F4 Cooling capacity 1 kw EER Net weight kg Compressors Scroll Quantity Power input kw Absorbed current A Capacity steps Fans EC-type axial Quantity Airflow m³/h Power input kw Evaporator BPHE Water flow rate m³/h Pressure drop kpa Evaporation temp. C Refrigerant circuits R410a Quantity Charge kg (1) Coolant: Water 100%; Coolant temperatures: 7/12 C; Ambient temperature: 35 C; Relative humidity: 50% MODELS 22 AVAILABLE The development of Kaltra products and services is continuous and the information in this document may not be up to date. Please check the current position with Kaltra.