AXE 6 DIGITAL MULTI-FUNCTION MICROPROCESS COUNTER/TIMER (72x72mm)

Transcription

1 AXE 6 DIGITA MUTI-FUNCTION MICROPROCESS COUNTER/TIMER (7x7mm) MM76 series Feaures Couner and imer funcion can be selecive Eleven oupu mode(a/a/a/a/b/b/b/c/d/e/f)can be modified Pulse inpu ype NPN/PNP can be modified 6BIT DAC analog oupu can be modified, Couning range ~ digi Two alarm funcion Rese by panel or connec erminal and Overflow auo zero RS485 Communicaion inerface,proocol MODBUS RTU MODE Five couning inpu modes:fron/afer edge Up,Down,Up/Down BAUD RATE:9/96/48/4,direc-Up/Down and Quadraure-Up/Down can be modified Man-machine inerface,easy o operae Inpu scaling muliplied(.~ ) can be modified EEPROM Saving,daa safekeeping abou years Quadraure sensing up o 4 imes resoluion Proecion class NEMA4/IP67 Ten alarm oupu mode (N/F/R/Q/C/P/K/A//) can be modified Noe: Boh couner and imer funcion Twelve ime range( sec. o hr.) can be modified Couner funcion, Timer funcion Name Of Pars Connecion Diagram Rev..

2 Key Inroduce key Funcion RST key Funcion AARM key Funcion A-ADJ key Funcion key Funcion Each key Funcion key Funcion & key Funcion Operaion Manual. In normal display, The key funcion is call ou seing group. In parameer seing page, The key funcion is daa ener, and goo nex page In any saus, Press RST key will be rese couner/imer and saus Couning mode in normal display,. call ou A seing page(press key abou sec). selec A~A alarm display in SV(Press key abou. sec) In normal display, call ou Azero & Aspan seing page(press key abou sec) Ino parameer seing page,he parameer mark&daa is alernae display,if need modify daa can press key ino seing procedure,the display is lock parameer daa, his ime mus le off key abou. sec,press again,he cursor(winkle express)is cycle moving lef.(key Response abou. sec) Ino parameer seing page, he parameer mark&daa is alernae display, If need modify daa can press each key ino seing procedure, The display is lock parameer daa, his ime mus le off key abou. sec, press again, he parameer daa will incremen. (Key Response abou. sec) Ino parameer seing page, he parameer mark&daa is alernae display, If need modify daa can press key ino seing procedure, The display is lock parameer daa, his ime mus le off key abou. sec, press again he parameer daa will decremen. (Key Response abou. sec) In seing group or seing page,press & key reurn normal display, bu if in seing page he modify daa will be los No key in anyhing In seing group or seing page no key in anyhing abou minues, reurn normal display Couner/Timer inside parameer operae procedure Sep Parameer Mark Descripion Parameer Mark Operaion Manual Normal display Press /FUNC key ino P.CODE seing page P.CODE(Pass code inpu page) Defaul= 4 TYPE(Type) Defaul=COUNT SYS(Sysem Seing Group) ROP(Alarm oupu Seing Group) AOP(Analog oupu Seing Group) DOP(Communicaion seing group).key in 6 digi pass code wih per digi & & key.press key, If he pass code is correc hen ino TYPE seing page, oherwise reurn normal display.decide Type wih digi or key (couner/imer).press key ener daa and ino SYS seing group.selec seing group wih key.press key ino seing page of selecion seing group PS. Timer don have ROP seing group 4A SYS(Sysem Seing Group for Couner) DP(Decimal Poin seing page) 4A- Defaul = 4A- 4A- 4A-4 4A-5 4A-6 4A-7 4B 4B- C-I-T(Coun Inpu Type) Defaul = NPN I-MODE(Inpu Mode) Defaul = UD C-R-S(Coun Raes Selec) Defaul = 5Kz RST-T(Rese Time) Defaul = ms SCAE (Scale ) Defaul =. P-OFF.M(Power Off Mode) Defaul=RESET SYS (Sysem Seing Group for Timer) T-RANG(Time Range) Defaul = sec..press key decide SYS for Couner Seing Group, Press key ino DP seing Page.Decide decimal poin posiion wih digi or key ( o 5).Press key ener daa and ino C-I-T seing page.decide Coun Inpu Type wih digi or key (NPN, PNP). Press key ener daa and ino I-MODE seing page. Decide inpu mode wih digi or key (UG/DG/UD/PD/AB). Press key ener daa and ino C-R-S seing page. Decide Coun Raes Selec wih digi or key (5z,5Kz). Press key ener daa and ino RST-T seing page.decide rese ime wih digi or key(ms, ms).press key ener daa and ino SCAE seing page.decide scale wih per digi & & key (.~ ).Press key ener daa and ino P-OFF.M seing page.decide rese ime wih digi or key (Rese or Memory). Press key ener daa and ino CODE seing page (4C-) Noe:Rese:Rese afer power off Memory:Keep save afer power off.press key decide SYS for Timer Seing Group, Press key ino T-RANG seing Page.Decide Time Range wih digi or key ( sec/ sec/ sec/sec/99min59.99sec/999min59.9sec/ min/ min/ 99hr59min59sec/9999hr59min/ hr/hr). Press key ener daa and ino C-I-T seing page Noe: While T-RANG change, Timer will rese Rev..

3 4B- 4B- 4B-4 4B-5 4B-6 4B-7 C-I-T(Coun Inpu Type) Defaul = NPN T.D.SE(Time Direcion Selec) Defaul = Up IN.TIME(Inpu Signal Time) Defaul=mS OP.MODE(Oupu Mode) Defaul=A OP.TIME(Oupu Acive Time) Defaul= OP-C-T(Oupu Conac Type) Defaul = 4C- CODE(Code) Defaul= 4C OCK(Panel ock) Defaul=NO ROP (Alarm seing group for Couner) OP.MODE(Oupu Mode) Defaul=N ACT.T (Acive Time ) Defaul= ACT.T (Acive Time ) Defaul=.Decide Coun Inpu Type wih digi or key (NPN, PNP). Press key ener daa and ino T.D.-SE seing page. Decide Time Direcion Selec wih digi or key (/). Decide Inpu Signal Time wih digi or key (ms/ms). Press key ener daa and ino OP.MODE seing page. Decide Inpu Signal Time wih digi or key (A/A/A/A/B/B/B/ C/D/E/F). Press key ener daa and ino OP.TIME seing page Noe : While TYPE change, OP.MODE reurn o defaul. Press key ener daa and ino IN.TIME seing page Noe:Up:PV display he elapsed ime, Down:PV display he remaining ime Noe : While OP.MODE change, imer rese. Decide Oupu Acive Time wih digi ~ (.~99.9)Sec. Press key ener daa and ino OP-C-T seing page Noe:OP.TIME= denoe self-holding oupu,op.time=.~99.9 is one-sho oupu Noe:OP.MODE=C,D,E mode is unconcerned wih OP.TIME.. Decide Oupu Conac Type wih digi or key (/c). Press key ener daa and ino CODE seing page(4c-) Noe::ou- & ou-=ime-limi,c:ou-=ime-limi,ou-=insananeous conac. Decide pass code wih per digi & & key (~). Press key ener daa and ino OCK seing page.decide panel lock wih digial & key(no or YES).Press key ener daa and reurn SYS seing group Noe:ock=Yes, only A/ TIME_T can be modified press key decide ROP for couner seing group, press key ino OP.MODE seing page. Decide oupu mode wih digial & key (N/F/R/Q/C/P/K/A//). Press key ener daa and ino ACT.T seing page Noe : While TYPE change, OP.MODE reurn o defaul Noe : While OP.MODE change, couner rese. Decide Acive ime wih digi ~ & & key (.~99.9)Sec. Press key ener daa and ino ACT.T seing page Noe :ACT-T= sec. denoe self-holding oupu ACT-T=.~99.99 sec. denoe one-sho oupu Noe :OP.MODE=/, The oupu mode is unconcerned wih ACT-T. Decide Acive ime wih digi ~ & & key (.~99.9)Sec. Press key ener daa and reurn ROP seing group Noe :ACT-T= sec. denoe self-holding oupu ACT-T=.~99.99 sec. denoe one-sho oupu Noe :OP.MODE=/, The oupu mode is unconcerned wih ACT-T 6 AOP(Analog oupu seing group) Press key decide AOP seing group, press key ino ANO seing page ANO(Analog Oupu Zero-.Decide ANO wih per digi & & key (-99999~) According o Display). Press Defaul= key ener daa and ino ANI seing page.decide ANI wih per digi & & key(-99999~).press key ener daa and reurn AOP seing page 6-6- ANI(Analog Oupu Span- According o Display ) Defaul= 7 DOP(Communicaion seing group) Press key decide DOP seing group, press key ino ADDR seing page ADDR(Communicaion Address ).Decide address wih digi ~ & & key(~55) Defaul=.Press key ener daa and ino BAUD seing page BAUD(Communicaion Baud Rae).Decide baud rae wih digial & key(9,96,48,4) Defaul=9.Press key ener daa and ino PARI seing page PARI(Communicaion Pariy Check).Decide pariy check wih digial & key(n8,n8,even,odd) Defaul=n8.Press key ener daa and reurn DOP seing group Ouside funcion key operae procedure (alarm seing for Couner mode) Sep Parameer mark descripion Parameer mark Operaion manual 8A- A (Alarm ) Defaul=.In normal display, press AARM key(abou S),ino A seing page. Decide A wih per digi & & key (~). No key in anyhing 5S or Press key ener daa and reurn normal display Rev..

4 . In normal display, press each key o enable seing A. A (Alarm ) 8A-. Decide A wih per digial & & key (~) Defaul=. No key in anyhing 5S or Press key ener daa and reurn normal display Ouside funcion key operae procedure (Timer ime seing for Timer mode) Sep Parameer mark descripion Parameer mark Operaion manual. In normal display, press each key o enable seing Time_T Time-T (Timer-Time ) 8B-. Decide TIME_T wih per digial & & key (~) Defaul=. No key in anyhing 5S or Press key ener daa and reurn normal display Ouside funcion key operae procedure (analog oupu adjus) Sep Parameer mark descripion Parameer mark Operaion manual 9 Normal display.press A-ADJ key abou sec, ino AZERO seing page AZERO(Analog Oupu Zero 9- Adjusmen page) Defaul= 9- ASPAN(Analog Oupu Span Adjusmen page) Defaul= Appendix Error Mark descripion Error Mark Analyze & Descripion EEPROM error deec.adjusmen analog oupu zero wih digi ~4 & & key(±6). Press key ener daa and ino ASPAN adjusmen page. Adjusmen analog oupu span wih digi ~4 & & key (±6). Press key ener daa and reurn normal display.exernal inerference when EEPROM read/wrie.eeprom wrie over imes (guaranee years) Please power rese,if sill display E-,doing following sep:. E- & No alernae display for inquire rese EEPROM. Decide Yes wih & key,press key reurn normal display. EEPROM was rese,please follow sep ~9 seing again 4 Rev..

5 Couner Inpu Type and Coun Value UG(PNP) :Coun inpu; : Prohibi(gae)inpu 5 (Incremen)Type UG(NPN) :Coun inpu; : Prohibi(gae)inpu 5 Coun 4 Coun 4 DG(PNP) :Coun inpu; : Prohibi(gae)inpu n n- (Decremen)Type DG(NPN) : Coun inpu; : Prohibi(gae)inpu n n- Coun n- n- n-4 Coun n- n- n-4 n-5 n-5 UD(PNP) / Type UD(NPN) Coun Coun PD(PNP) PD(NPN) Coun Coun AB(x4 mode) Coun 5 Rev..

6 Couner Alarm Oupu Mode Inpu Mode / N Couner Alarm Oupu Mode seing F Rese A A Rese A A Operaion Descripion The display coninues o increase/decrease. The oupu are held unil Rese is inpu. As soon as has acive,he display are held unil Rese is inpu. The oupu ime is independen of. R Q C Rese A A Rese A A Rese A A Noe:. Self-holding oupu, One-sho oupu, Self-holding oupu or One-sho oupu The display coninues o increase/ decrease during he one-sho oupu ime.bu reurn o he rese sar saus afer he one-sho oupu ime has elapsed. The oupu repea one-sho operaion. self-holding oupu urns OFF afer he one-sho oupu ime.the one-sho oupu ime is independen of. The display reurn o he rese sar saus afer he one-sho oupu ime. The oupu repea one-sho operaion. self-holding oupu urns OFF afer he one-sho oupu ime. The one-sho oupu ime is independen of. As soon as he coun reaches A,he display reurn o he rese sar saus The oupu repea one-sho operaion. self-holding oupu urns OFF afer he one-sho oupu ime. The one-sho oupu ime is independen of. One-sho oupu 6 Self-holding oupu Rev..

7 Couner Alarm Oupu Mode seing P K Rese A A Rese A A Inpu Mode / Operaion Descripion The display dose no change during he one-sho oupu ime.bu he acual coun reurn o he rese sar saus. The oupu repea one-sho operaion. self-holding oupu urns OFF afer he one-sho oupu ime.the one-sho oupu ime is independen of OUT. The display coninues o increase/decrease. self-holding oupu urns OFF afer he one-sho oupu ime. The one-sho oupu ime is independen of. A Rese A A As soon as has acive,he display are held unil Rese is inpu. The oupu ime is independen of. Rese A A Rese A A The display coninues o increase/decrease unil he overflow or underflow is reached. is held while he presen is less han or equal o A. A he or / mode, is held while he presen is greaer han or equal o A. A he mode, is held while he presen is less han or equal o zero. The display coninues o increase/decrease unil he overflow or underflow is reached. is held while he presen is greaer han or equal o A. A he or / mode, is held while he presen is greaer han or equal o A. A he mode, is held while he presen is less han or equal o zero. Noe:.Couning canno be performed during Rese inpu..when coun reaches 99999,i reurn o ; Coun below , a Down mode reurn o A, a Up/Down mode reurn o 4.If Rese is inpu while one-sho oupu is ON, one-sho oupu urns OFF. 5.If power failure while oupu is ON, oupu will urn ON again(p.off.m=)or Rese(P.OFF.M=) when he power supply has recovered. 6.When coun reaches o alarm again during he One-sho oupu, he One-sho oupu ime will be resar. 7.Ten alarm oupu mode is according o A seing. 7 Rev..

8 Timer Oupu Mode Basic Operaion Descripion Deailed operaion Descripion Mode A: Signal ON delay (Timer reses when power comes ON) Sar START ON sar he iming,once reach seing, enable self-holding or one-sho,presen will be hold unil RESET ON or power supply recovered,and hen Presen rese. During he START ON, he imer sars when he power comes ON or when he RESET OFF. Sar signal inpu is disabled during iming. Once START ON, is insananeous when seing is. Mode A-: Signal ON delay (Timer reses when power comes ON) Sar Gae Rese / (OP-C-T=T) (OP-C-T=CT) Se Se Sar START ON sar he iming,once reach seing, enable self-holding or one-sho,presen will be hold unil START OFF or RESET ON or power supply recovered,and hen Presen rese. During he START ON, he imer sars when he power comes ON or when he RESET OFF. Once START ON, is insananeous when seing is. Mode A-: Power ON delay (Timer reses when power comes ON) Sar Gae Rese / (OP-C-T=T) (OP-C-T=CT) Se Se Boh power on and RESET OFF sar he iming,once reach seing, enable self-holding or one-sho,presen will be hold unil RESET ON or power supply recovered,and hen Presen rese. The sar signal disables he iming funcion as he gae inpu. During he power on, he imer sars when he RESET OFF Once power on, is insananeous when seing is. Mode A-: Power ON delay (Timer does no rese when power comes ON) Sar Gae Rese / (OP-C-T=T) (OP-C-T=CT) Se Se pause Coninuous Boh power on and RESET OFF sar he iming, If power off,he iming and will be pause unil power supply recovered. Once reach seing, enable self-holding or one-sho. Presen will be hold unil RESET ON. The sar signal disables he iming funcion as he gae inpu. Once power on, is insananeous when seing is. oupu pause Coninuous oupu Sar Gae Rese / (OP-C-T=T) (OP-C-T=CT) Se Se a -a 8 Rev..

9 Basic Operaion Descripion Deailed operaion Descripion Mode B: Repea cycle (Timer reses when power comes ON) Sar Sar Gae Rese / (OP-C-T=T) START ON sar he iming,once reach seing,he Presen rese and resar iming, enable one-sho or self-holding unil nex ime reach again.repea iming and oupu unil RESET (OP-C-T=CT) Se ON or power supply recovered,and hen Presen rese. Se During he START ON, he imer sars when he power comes ON or when he RESET OFF. Seing mus be a leas ms. (Relay oupu mode) Mode B-: Repea cycle (Timer does no rese when power comes ON) Sar ime=x+y X pause Y START ON sar he iming,once reach seing,he Presen rese and resar iming, enable one-sho or self-holding unil nex ime reach again.repea iming and oupu unil RESET ON. During he START ON,if power off,he iming will be pause unil power supply recovered. Seing mus be a leas ms. (Relay oupu mode) Mode B-: Repea cycle ON START (Timer reses when power comes ON) Sar Gae Rese / (OP-C-T=T) (OP-C-T=CT) Se Se Sar START ON sar he iming and enable one-sho or self- holding,once reach seing,boh presen and rese.repea he iming and oupu unil RESET ON. Seing mus be a leas ms. (Relay oupu mode) Mode C: Signal ON/OFF START (Timer reses when power comes ON) Sar Rese / (OP-C-T=T) (OP-C-T=CT) Se Se Sar Sar Rese START ON or START OFF sar he iming and enable self-holding unil reach seing During START ON,Presen will be rese and pause period of he RESET ON START ON or START OFF mus greaer han TIME-T / (OP-C-T=T) (OP-C-T=CT) Se Se 9 Rev..

10 Basic Operaion Descripion Deailed operaion Descripion Mode D: Signal OFF DEAY (Timer reses when power comes ON) Sar Sar Gae Rese START OFF sar he iming,once reach seing or RESET ON or START ON or power supply recovered,he presen will be rese. The is ON during START ON (excep when he power is OFF or RESET ON) When seing is, he only ON during he START ON Mode E: Inerval (Timer reses when power comes ON) / (OP-C-T=T) (OP-C-T=CT) Se Se Sar Sar Gae Rese START ON sar he iming,once reach seing or RESET ON or power supply recovered,he presen will be rese. START ON sar he iming,he is ON unil reach seing or RESET ON or power supply recovered. is disabled when he seing is. / (OP-C-T=T) (OP-C-T=CT) Se Se Mode F: Cumulaive (Timer does no rese when power comes ON) Sar Sar Seing = X + Y START ON sar he iming,once reach seing, enable self-holding or one-sho,presen and will be hold unil he RESET ON. X pause Y During power off,he presen is hold,and pause. Once START ON, is insananeous when seing is. When he power sar, here will be a imer error (exceeding ms each ime).use he signal sar if imer accuracy is required. Gae Rese / (OP-C-T=T) (OP-C-T=CT) Se Se Rev..

11 MM76 Modbus RTU Mode Proocol Address Map Daa forma 6Bi/Bi, sign bi 8~7FFF(-768~767),8~7FFFFFFF( ~ ) Address Name Descripion Address DISPM SV display indicae, Inpu Range ~(~) (:A, :A) R/W TYPE TYPE,Inpu Range ~(~) (:COUNT, :TIME) R/W C-I-T Coun Inpu Type, Inpu Range ~ (~) (:NPN,:PNP) R/W DP Decimal Poin,Inpu Range ~5 (~5)(:,: -,: -,: -,4: -4,5: -5 ) R/W 4 I-MODE Inpu mode, Inpu Range ~4 (~4) (:UG, :DG, :UD, :PD, 4:AB) R/W 5 C-R-S Coun Raes Selec,Inpu Range ~ (~) (:5z,:5Kz) R/W 6 RST_T Rese ime,inpu Range ~ (~) (:ms,:ms) R/W 7 P-OFF.M Power Off Mode, Inpu Range ~ (~) (:Rese, :Memory) R/W Time Range, Inpu Range ~B ((~B), (: sec), (: sec), (: sec), (:sec), 8 T-RANG (4:99min59.99sec), (5:999min59.9sec), (6: min), (7:min), (8:99hr59min59sec), (9:9999hr59min), (A: hr), (B:hr) R/W 9 T.D.SE Time Direcion Selec, Inpu Range ~ (~)(:, :) R/W A IN.TIME Inpu Signal Time, Inpu Range ~ (~) (:ms, :ms) R/W B OP-C-T Oupu Conac ype, Inpu Range ~ (~) (:, :c) Oupu mode for couner, Inpu Range ~9(~9)(:N, :F, :R, :Q, 4:C, 5:P, 6:K, 7:A, 8:, 9:) C OP.MODE Oupu mode for imer, Inpu Range ~A (~A) (:A, :A, :A, :A, 4:B, 5:B, 6:B, 7:C, 8:D, 9:E, A:F) R/W D OCK Panel ock, Inpu Range ~ (~)(NO/YES) R/W E OP_TIME Oupu Acive Time, Inpu Range ~E7(.~99.9) F ACT.T Acive Time, Inpu Range ~E7(.~99.9) R/W ACT.T Acive Time, Inpu Range ~E7(.~99.9) R/W ADDR Communicaion Address, Inpu Range ~FF (~55) R/W BAUD Communicaion Baud Rae, Inpu Range ~ (~)( :9,:96,:48,:4) R/W PARI Communicaion Pariy Check, Inpu Range ~ (~)(:N8,:N8,:EVEN,:ODD) R/W 4 AZERO Analog Oupu Zero Adjus,Inpu Range E89~77 (-6~6) R/W 5 ASPAN Analog Oupu Span Adjus,Inpu Range E89~77 (-6~6) R/W 6 CODE Pass Code, Inpu Range ~F4F (~)high word R/W 7 Pass Code, Inpu Range ~F4F (~)low word R/W 8 SCAE Display Scale, Inpu Range ~F4F (.~ )high word R/W 9 Display Scale, Inpu Range ~F4F (.~ )low word R/W A ANO Analog Oupu Zero According o Display, Inpu Range FFFCFC~F4F (-99999~)high word R/W B Analog Oupu Zero According o Display, Inpu Range FFFCFC~F4F (-99999~)low word R/W C ANI Analog Oupu Span According o Display,Inpu Range FFFCFC~F4F (-99999~)high word R/W D Analog Oupu Span According o Display,Inpu Range FFFCFC~F4F (-99999~)low word R/W E A A, Inpu Range ~F4F (~)high word R/W F A, Inpu Range ~F4F (~)low word R/W A A, Inpu Range ~F4F (~)high word R/W A, Inpu Range ~F4F (~)low word R/W TIME-T TIME-T, Inpu Range ~F4F (~)high word R/W TIME-T, Inpu Range ~F4F (~)low word R/W 4 DISP Display Value, Display Range FFFCFC~F4F (-99999~)high word R 5 Display Value, Display Range FFFCFC~F4F (-99999~)low word R 6 STATUS Saus, Display Range ~(~) (:OFF,:ON)(Bi:OUT, Bi:OUT, Bi~Bi6:Reserve) R 7 RST Wrie = (Funcion 6), coun/ime rese W Rev..