GRUNDFOS DATA BOOKLET TP, TPD, TPE, TPED. In-line circulator pumps 50 Hz

Transcription

1 GRUNDFOS DATA BOOKLET TP, TPD, TPE, TPED In-line circulator pumps Hz

2 Contents Pump data Introduction TP, mains-operated pumps TPE, speed-controlled pumps Type key 5 Codes for shaft seal 5 Performance range Performance range, 2-pole, PN 6, 1, 16 6 Performance range, -pole, PN 6, 1, 16 7 Performance range, 6-pole, PN 16 8 Performance range, 2-pole, PN 25 9 Performance range, -pole, PN 25 1 Product range Product range, 2-pole, PN 6, 1, Product range, -pole, PN 6, 1, Product range, 6-pole, PN Product range, 2-pole, PN Product range, -pole, PN Operating conditions System and test pressures 17 Sound pressure level 17 Ambient temperature 17 Pumped liquids Pumped liquids 18 Liquid temperature 18 List of pumped liquids 19 TP Series 1 and 2 pumps Technical data 21 Construction 21 Materials 21 Mechanical shaft seal 22 Connections 22 Features and benefits 22 TP Series 3 pumps Technical data 23 Construction 23 Materials 23 Mechanical shaft seal 23 Connections 2 Features and benefits 2 TP Series pumps Technical data 25 Construction 25 Materials 25 Mechanical shaft seal 26 Connections 26 Features and benefits 26 TPE Series 1 pumps Technical data 27 Construction 27 Applications 27 TPE(D) pumps with extended performance range 28 Operating modes of twin-head pumps 28 Control options 28 TPE Series 2 pumps Technical data 29 Construction 29 Applications 29 TPE(D) pumps with extended performance range 3 Operating modes of twin-head pumps 3 Control options 3 Communication Communication with TPE, TPED pumps 31 Speed regulation of TPE pumps Affinity equations 32 TP, TPE pumps in parallel Control of TP, TPE pumps connected in parallel 33 Alternation/standby function of TPED pumps 33 TP, TPE pumps connected to Control MPC 33 TPE Series 2 pumps connected to Control MPC Series 2 3 Grundfos CUE TP pumps connected to Grundfos CUE, external frequency converters 35 Functions 35 External communication 35 Motor data Motors 36 Motor protection 37 Electrical data, mains-operated motors 38 Electrical data, speed-controlled motors 2

3 Contents Installation Mechanical installation 1 Electrical installation 6 Flanges for TP pumps Flange dimensions 8 Curve charts How to read the curve charts 9 Curve conditions Technical data/performance curves TP, TPD, TPE, TPED, 2-pole, PN 6, 1, TP, TPD, TPE, TPED, -pole, PN 6, 1, 16 7 TP, TPD, TPE, TPED, 6-pole, PN 16 1 TP, 2-pole, PN 25 1 TP, -pole, PN Weights and shipping volume TP, TPD, TPE, TPED, 2-pole, PN 6, 1, TP, TPD, TPE, TPED, -pole, PN 6, 1, TP, TPD, 6-pole, PN 6, 1, TP, 2-pole, PN TP, -pole, PN Accessories Unions and valves 125 Counter flanges 126 Base plates 129 Blanking flanges 131 Insulating kits 135 Sensors 136 Potentiometer 137 R1 137 CIU communication interface units 137 CIM communication interface modules 138 EMC filter 138 Minimum inlet pressure - NPSH TP, TPD, 2-pole, PN 6, 1, 16 1 TP, TPD, -pole, PN 6, 1, TP, TPD, 6-pole, PN TP Series, 2-pole, PN TP Series, -pole, PN Further product documentation WebCAPS 13 WinCAPS 1 3

4 Pump data TP, TPD, TPE, TPED Introduction TP pumps are designed for applications such as district heating systems heating systems air-conditioning systems district cooling systems water supply industrial processes industrial cooling. The pumps are available with either mains-operated motors (TP and TPD) or electronically speed-controlled motors (TPE and TPED). The pumps are all single-stage, in-line centrifugal pumps with mechanical shaft seal. The pumps are of the close-coupled type, i.e. pump and motor are separate units. Consequently, the pumps are less sensitive to impurities in the pumped liquid than similar pumps of the canned rotor type. TP, mains-operated pumps The TP range is divided into the following four groups based on their construction: TP Series 1, 2, 3 and. TP Series 1 with union or flange connection Rp 1 (DN 25) to Rp 1 1/ (DN 32) and motor sizes from.12 to.25 kw. For further information, see page 21. TP Series 2 with flange connection DN 32 to DN 1 and motor sizes from.12 to 2.2 kw. For further information, see page 21. TP Series 3 with flange connection DN 32 to DN 2 and motor sizes from.25 to 132 kw. For further information, see page 23. TP Series with flange connection Grundfos offers two TP Series versions: 1 bar version with DN 2 flange and motor sizes from 5 to 75 kw. 25 bar version with DN 1 to DN and motor sizes from 5.5 to 63 kw. For further information, see page 25. TPE, speed-controlled pumps Based on the construction and choice of material of TP pumps, Grundfos offers the following two series of speed-controlled TPE pumps: TPE Series 1 pumps (without factory-fitted differential-pressure sensor) TPE Series 2 pumps (with factory-fitted differential-pressure sensor) TPE Series 1 pumps The difference between the TP and the TPE Series 1 pump range is the motor. The motors of TPE Series 1 pumps have built-in frequency converter. Via an external signal (from a sensor or a controller), TPE Series 1 pumps allow for any configuration and control method required: Constant pressure, temperature or flow. For further information, see page 27. TPE Series 2 pumps The main differences between the TP and the TPE Series 2 pumps are the motor and the factory-fitted differential-pressure sensor. TPE Series 2 pumps are factory-set to proportionalpressure control. The motors of TPE Series 2 pumps have built-in frequency converter for continuous adjustment of the pressure to the flow rate. The TPE Series 2 range is recognized as a preset solution for quick and safe installation. For further information, see page 29. Why select a TPE pump? A TPE pump with electronic speed control offers these obvious benefits: energy savings increased comfort control and monitoring of pump performance communication with the pump. ATEX-approved TP pumps On request, Grundfos offers TP and TPD pumps with ATEX-approval. All ATEX-approved TP pumps are in accordance with Council directive 9/9/EC (Group II, category 3). If an ATEX-approved dry-running protection is installed, the pump can be upgraded to category 2G. High-efficiency motors TP pumps are fitted with high-efficiency motors. TP pumps are primarily fitted with motors that meet the legislative requirements of the EuP IE3 grade. For further information, see section Motors on pages 36 to. IE3

5 Pump data TP, TPD, TPE, TPED Type key Example TP E D /2 -S -A -F -A -BUBE Pump range Electronically speed-controlled pump (Series 1, 2) Twin-head pump Nominal diameter of suction and discharge ports (DN) Maximum head [dm] Pole number S = TPE Series 2 (with factory-fitted differential pressure sensor) Code for pump version: A = Basic version I = PN 6 flange X = Special version Code for pipework connection: F = DIN flange O =Union Code for materials: A = Basic version Z = Bronze pump housing and pump head B = Bronze impeller Code for shaft seal (incl. other plastic and rubber pump parts, except the neck ring) Codes for shaft seal Example B U B E Grundfos type designation A = O-ring seal with fixed seal driver B = Rubber bellows seal D = O-ring seal, balanced G = Bellows seal with reduced seal faces R = O-ring seal with reduced seal faces Material of rotating face A = Carbon, antimony-impregnated B = Carbon, resin-impregnated Q = Silicon carbide U = Tungsten carbide Material of stationary seat B = Carbon, resin-impregnated Q = Silicon carbide U = Tungsten carbide Material of secondary seal E = EPDM P = NBR rubber V = FKM 5

6 Performance range TP, TPD, TPE, TPED 2-pole, PN 6, 1, 16 Performance range, 2-pole, PN 6, 1, 16 (See page 52 for performance curves) p [kpa] H TM TP(D), TPE(D) PN 6/1/16, 2-pole, Hz R R R R Q [m³/h] Q [l/s] Note: All QH curves apply to single-head pumps. For further information about curve conditions, see page. The hatched area shows the performance range of TPE pumps. 6

7 Performance range TP, TPD, TPE, TPED -pole, PN 6, 1, 16 Performance range, -pole, PN 6, 1, 16 (See page 7 for performance curves) p [kpa] H TM TP(D), TPE(D) PN 6/1/16, -pole, Hz Q [m³/h] Q [l/s] Note: All QH curves apply to single-head pumps. For further information about curve conditions, see page. The hatched area shows the performance range of TPE pumps. 7

8 Performance range TP, TPD 6-pole, PN 16 Performance range, 6-pole, PN 16 (See page 1 for performance curves) p [kpa] H TM TP(D) PN 16, 6-pole, Hz / / / /6 1-11/6 1-9/ / /6 1-7/6 1-6/ Q [m³/h] Q [l/s] Note: All QH curves apply to single-head pumps. For further information about curve conditions, see page. 8

9 Performance range TP 2-pole, PN 25 Performance range, 2-pole, PN 25 (See page 1 for performance curves) p [kpa] H TM TP PN 25, 2-pole, Hz Q [m³/h] Q [l/s] 9

10 Performance range TP -pole, PN 25 Performance range, -pole, PN 25 (See page 16 for performance curves) p [kpa] H TM TP PN 25, -pole, Hz Q [m³/h] Q [l/s] 1

11 Product range TP, TPD, TPE, TPED Product range, 2-pole, PN 6, 1, 16 Design Shaft seal Pressure stage Materials Mains-operated motor Electronically speed-controlled motor Pump housing Impeller Voltage [V] Voltage [V] Pump type TPE Series 1 TPE Series 2 TP Series 1 TP Series 2 TP Series 3 TP Series BUBE AUUE RUUE BAQE BQQE GQQE DBUE PN 6 PN 1 PN 16 PN 25 Cast iron EN-GJL-2 Nodular cast iron EN-GJS--18 Bronze 1) TP 25-/2 R TP 25-9/2 R TP 32- /2 R TP 32-9/2 R TP, TPD 32-6/ TP, TPD 32-12/ TP, TPD 32-1/ TP, TPD 32-18/ TP, TPD 32-23/ TP, TPD 32-2/ TP, TPD 32-2/ TP, TPD 32-32/ TP, TPD 32-38/ TP, TPD 32-6/2... TP, TPD 32-58/ TP -/ TP, TPD -6/ TP -9/ TP, TPD -12/ TP -18/ TP, TPD -19/ TP, TPD -23/ TP, TPD -27/ TP, TPD -2/ TP, TPD -3/ TP, TPD -36/2... TP, TPD -7/ TP, TPD -58/ TP, TPD -6/ TP, TPD -12/ TP, TPD -18/ TP, TPD -16/ TP, TPD -19/ TP, TPD -2/ TP, TPD -29/ TP, TPD -36/2... TP, TPD -3/ TP, TPD -/ TP, TPD -57/ TP, TPD -71/ TP, TPD -83/ TP, TPD -9/ TP, TPD 65-6/ TP, TPD 65-12/ TP, TPD 65-18/ TP, TPD 65-19/ TP, TPD 65-23/ TP, TPD 65-26/2... TP, TPD 65-3/ Stainless steel Cast iron Nodular cast iron EN-GJS--15 Bronze 1 x ΔV/ 2 YV P 2 3 x 22-2 ΔV/ YV P 2 3 x ΔV/ YV 2) P 2 1 x 22-2 V P 2 3 x 38-8 V P 2 11

12 Product range TP, TPD, TPE, TPED Design Shaft seal Pressure stage Materials Mains-operated motor Electronically speed-controlled motor Pump housing Impeller Voltage [V] Voltage [V] Pump type TP, TPD 65-1/ TP, TPD 65-6/ TP, TPD 65-5/ TP, TPD 65-66/ TP, TPD 65-72/ TP, TPD 65-93/ TP, TPD 8-12/ TP, TPD 8-1/ TP, TPD 8-18/ TP, TPD 8-21/2... TP, TPD 8-2/ TP, TPD 8-2/ TP, TPD 8-33/ TP, TPD 8-/ TP, TPD 8-52/ TP, TPD 8-57/ TP, TPD 8-7/ TP, TPD 1-12/ TP, TPD 1-16/2... TP, TPD 1-2/ TP, TPD 1-2/ TP, TPD 1-2/ TP, TPD 1-31/ TP, TPD 1-36/ TP, TPD 1-39/ TP, TPD 1-8/ Standard. TPE Series 1 TPE Series 2 TP Series 1 TP Series 2 TP Series 3 TP Series BUBE AUUE RUUE BAQE BQQE GQQE DBUE PN 6 PN 1 PN 16 PN 25 1) Bronze versions are only available as single-head pumps. Cast iron EN-GJL-2 Nodular cast iron EN-GJS--18 Bronze 1) 2) 2-pole motors above 5.5 kw can be operated at 3 x YV. Smaller motor sizes cannot. Stainless steel Cast iron Nodular cast iron EN-GJS--15 Bronze 1 x ΔV/ 2 YV P 2 3 x 22-2 ΔV/ YV P 2 3 x ΔV/ YV 2) P 2 1 x 22-2 V P 2 3 x 38-8 V P 2 12

13 Product range TP, TPD, TPE, TPED Product range, -pole, PN 6, 1, 16 Design Shaft seal Pressure stage Materials Mains-operated motor Electronically speed-controlled motor Pump housing Impeller Voltage [V] Voltage [V] Pump type TPE Series 1 TPE Series 2 TP Series 1 TP Series 2 TP Series 3 TP Series BUBE AUUE RUUE BAQE BQQE GQQE DBUE PN 6 PN 1 PN 16 PN 25 Cast iron EN-GJL-2 Nodular cast iron EN-GJS--18 Bronze 1) TP, TPD 32-3/ TP, TPD 32-/ TP, TPD 32-6/ TP, TPD 32-8/ TP, TPD 32-1/ TP, TPD 32-12/ TP, TPD -3/ TP -6/ TP, TPD -9/ TP, TPD -1/ TP, TPD -13/ TP, TPD -16/ TP, TPD -3/ TP, TPD -6/ TP, TPD -9/ TP, TPD -11/ TP, TPD -13/ TP, TPD -16/ TP, TPD -19/ TP, TPD -23/ TP, TPD 65-3/ TP, TPD 65-6/ TP, TPD 65-9/ TP, TPD 65-11/ TP, TPD 65-13/ TP, TPD 65-1/ TP, TPD 65-17/ TP, TPD 65-2/... TP, TPD 8-3/ TP, TPD 8-6/ TP, TPD 8-7/ TP, TPD 8-9/ TP, TPD 8-11/ TP, TPD 8-1/ TP, TPD 8-17/... TP, TPD 8-2/ TP, TPD 8-27/ TP, TPD 8-3/ TP, TPD 1-3/ TP, TPD 1-6/ TP, TPD 1-7/ TP, TPD 1-9/ TP, TPD 1-11/ TP, TPD 1-13/... TP, TPD 1-17/ TP, TPD 1-2/ TP, TPD 1-2/ TP, TPD 1-33/ TP, TPD 1-37/ Stainless steel Cast iron Nodular cast iron EN-GJS--15 Bronze 1 x ΔV/ 2 YV P 2 3 x 22-2 ΔV/ YV P 2 3 x ΔV/ YV 2) P 2 1 x 22-2 V P 2 3 x 38-8 V P 2 13

14 Product range TP, TPD, TPE, TPED Design Shaft seal Pressure stage Materials Mains-operated motor Electronically speed-controlled motor Pump housing Impeller Voltage [V] Voltage [V] Pump type TP, TPD 1-1/ TP, TPD /... TP, TPD / TP, TPD / TP, TPD / TP, TPD 125-2/ TP, TPD / TP, TPD / TP, TPD 125-2/ TP, TPD 1-13/ TP, TPD 1-16/ TP, TPD 1-2/ TP, TPD 1-22/ TP, TPD 1-2/ TP 1-26/ TP 1-28/ TP 1-3/ TP 1-39/ 37. TP 2-18/ TP 2-22/ TP 2-2/ 37. TP 2-27/ 5. TP 2-32/ 55. TP 2-33/ 37. TP 2-36/ 5. TP 2-/ 55. TP 2-1/ 75. TP 2-7/ 75. TP 2-53/ 9 TP 2-59/ 11 TP 2-66/ 132 TP 2-28/ 5. TP 2-31/ 55. TP 2-39/ 75. Standard. TPE Series 1 TPE Series 2 TP Series 1 TP Series 2 TP Series 3 TP Series BUBE AUUE RUUE BAQE BQQE GQQE DBUE PN 6 PN 1 PN 16 PN 25 1) Bronze versions are only available as single-head pumps. Cast iron EN-GJL-2 2) -pole motors above kw can be operated at 3 x YV. Smaller motor sizes cannot. Nodular cast iron EN-GJS--18 Bronze 1) Stainless steel Cast iron Nodular cast iron EN-GJS--15 Bronze 1 x ΔV/ 2 YV P 2 3 x 22-2 ΔV/ YV P 2 3 x ΔV/ YV 2) P 2 1 x 22-2 V P 2 3 x 38-8 V P 2 1

15 Product range TP, TPD, TPE, TPED Product range, 6-pole, PN 16 Design Shaft seal Pressure stage Materials Mains-operated motor Electronically speed-controlled motor Pump housing Impeller Voltage [V] Voltage [V] Pump type Standard. TPE Series 1 TPE Series 2 TP Series 1 TP Series 2 TP Series 3 TP Series BUBE AUUE RUUE BAQE BQQE GQQE DBUE PN 6 PN 1 PN 16 PN 25 1) Bronze versions are only available as single-head pumps. Product range, 2-pole, PN 25 Cast iron EN-GJL-2 Nodular cast iron EN-GJS--18 Bronze 1) Stainless steel Cast iron TP, TPD 125-6/6 1.5 TP, TPD 125-7/ TP, TPD 125-9/ TP, TPD /6.. TP, TPD 125-1/ TP, TPD / TP, TPD 1-6/ TP, TPD 1-7/ TP, TPD 1-9/6.. TP, TPD 1-11/ Nodular cast iron EN-GJS--15 Bronze 1 x ΔV/ 2 YV P 2 3 x 22-2 ΔV/ YV P 2 3 x ΔV/ YV P 2 1 x 22-2 V P 2 3 x 38-8 V P 2 3 x V P 2 Design Shaft seal Pressure stage Materials Mains-operated motor Electronically speed-controlled motor Pump housing Impeller Voltage [V] Voltage [V] Pump type Standard. TPE Series 1 TPE Series 2 TP Series 1 TP Series 2 TP Series 3 TP Series BUBE AUUE RUUE BAQE BQQE GQQE DBUE PN 6 PN 1 PN 16 PN 25 Cast iron EN-GJL-2 Nodular cast iron EN-GJS--18 Bronze Stainless steel Cast iron TP 1-62/2 37. TP 1-7/2 5. TP 1-82/2 55. TP 1-96/2 75. TP 1-1/2 75. TP 1-118/2 9. TP 1-1/2 11. TP 1-153/ TP 1-168/2 16. Nodular cast iron EN-GJS--15 Bronze 1 x ΔV/ 2 YV P 2 3 x 22-2 ΔV/ YV P 2 3 x ΔV/ YV P 2 1 x 22-2 V P 2 3 x 38-8 V P 2 3 x V P 2 15

16 Product range TP, TPD, TPE, TPED Product range, -pole, PN 25 Design Shaft seal Pressure stage Materials Mains-operated motor Electronically speed-controlled motor Pump housing Impeller Voltage [V] Voltage [V] Pump type Standard. TPE Series 1 TPE Series 2 TP Series 1 TP Series 2 TP Series 3 TP Series BUBE AUUE RUUE BAQE BQQE GQQE DBUE PN 6 PN 1 PN 16 PN 25 Cast iron EN-GJL-2 Nodular cast iron EN-GJS--18 Bronze Stainless steel Cast iron TP 1-19/ 5.5 TP 1-22/ 7.5 TP 1-26/ 11. TP 1-27/ 11. TP 1-32/ 15. TP 1-38/ 18.5 TP 1-2/ 22. TP 125-1/ 7.5 TP 125-2/ 11. TP 125-2/ 15. TP / 15. TP / 18.5 TP / 22. TP 125-3/ 3. TP 1-2/ 18.5 TP 1-27/ 22. TP 1-32/ 3. TP 1-3/ 37. TP 1-3/ 5. TP 1-53/ 55. TP 1-6/ 75. TP 2-26/ 3. TP 2-28/ 37. TP 2-38/ 5. TP 2-2/ 55. TP 2-/ 55. TP 2-51/ 75. TP 2-56/ 9. TP 2-62/ 11. TP 2-27/ 5. TP 2-32/ 55. TP 2-37/ 75. TP 2-9/ 9. TP 2-5/ 11. TP 2-6/ 132. TP 2-66/ 16. TP 3-59/ 2. TP 3-67/ 2. TP 3-7/ 315. TP -7/ 315. TP -51/ 355. TP -5/. TP -67/. TP -72/ 56. TP -76/ 63. Nodular cast iron EN-GJS--15 Bronze 1 x ΔV/ 2 YV P 2 3 x 22-2 ΔV/ YV P 2 3 x ΔV/ YV P 2 1 x 22-2 V P 2 3 x 38-8 V P 2 16

17 Operating conditions TP, TPD, TPE, TPED System and test pressures Pressure System pressure Test pressure [bar] [MPa] [bar] [MPa] PN PN PN PN Sound pressure level Single-phase: Three-phase: Max. 7 db(a). See table below. Maximum sound pressure level [db(a)] - ISO 373 Motor Three-phase motors 2-pole -pole 6-pole The values apply only to MG and Siemens motors. The values have a tolerance of 3 db according to EN ISO 871; the tolerance is not added to the values in the table. Ambient temperature MG IE2 and IE3 motors: kw motors, 2-pole -3 to +6 C kw motors, -pole Siemens IE2 and IE3 motors: 3-9 kw motors, 2-pole -3 to +55 C kw motors, -pole MGE and other motor sizes -3 to + C Storage Down to -3 C If the ambient temperature exceeds above maximum values or if the motor is located more than 1 metres above sea level, the motor output (P 2 ) must be reduced due to the low density and consequent low cooling effect of the air. In such cases, it may be necessary to use an oversize motor with a higher rated output. Key [%] t [ C] m Fig. 1 Relationship between motor output (P 2 ) and altitude Pos. 1 Description Siemens IE2 and IE3 motors: 3-9 kw motors, 2-pole kw motors, -pole MG IE2 and IE3 motors: kw motors, 2-pole kw motors, -pole 3 MGE and other motor sizes TM The audible noise from TP pumps is primarily noise from the motor fan. The selection of TPE pumps will reduce the noise at partial load, as the motor, and consequently, the motor fan runs at a lower speed. Possible flow noise from control valves is also reduced at partial load in the case of the TPE pump. 17

18 Pumped liquids TP, TPD, TPE, TPED Pumped liquids Thin, clean, non-aggressive and non-explosive liquids, not containing solid particles or fibres that may mechanically or chemically attack the pump. See "List of pumped liquids" on page 19. Examples of liquids Central heating system water (the water should meet the requirements of accepted standards on water quality in heating systems) cooling liquids domestic hot water industrial liquids softened water. If glycol or another antifreeze agent is added to the pumped liquid, the pump must have a shaft seal of the type RUUE or GQQE. The pumping of liquids with densities or kinematic viscosities higher than those of water can have these consequences: a considerable pressure drop a drop in the hydraulic performance a rise in the power consumption. In these situations, equip the pump with an oversize motor. If in doubt, contact Grundfos. If the water contains mineral oils or chemicals, or if other liquids than water are pumped, the O-rings should be chosen accordingly. Liquid temperature Liquid temperature: -25 C to +1 C. Please note that shaft seals operating close to their maximum temperature will require regular maintenance, i.e. replacement. Pump type Shaft seal Temperature TP Series 1 TP Series 2 TP Series 3 TP Series, 1 bar version TP Series, 25 bar version BUBE C to +11 C BQQE C to +9 C GQQE -25 C to +9 C BUBE C to +1 C AUUE C to +9 C RUUE -25 C to +9 C BAQE C to +12 C (1 C) 1) BQQE C to +9 C GQQE -25 C to +9 C (6 C) 2) BAQE C to +12 C BQQE C to +9 C GQQE -25 C to +9 C DBUE C to +1 C 3) 1) TP Series 3 pumps are designed for a maximum operating temperature of 1 C. For operation above 12 C, an alternative shaft seal is to be selected. Contact Grundfos. 2) The below listed TP Series 3 pumps with GQQE shaft seals are designed for a maximum operating temperature of 6 C. TP 1-26/ TP 2-18/ TP 1-28/ TP 2-22/ TP 1-3/ TP 2-2/ TP 1-39/ TP 2-27/ TP 2-32/ TP 2-33/ TP 2-36/ TP 2-/ TP 2-1/ TP 2-7/ TP 2-53/ TP 2-59/ TP 2-66/ 3) At +12 to +1 C, the maximum operating pressure 23 bar. Depending on the type of cast iron used and the pump application, the maximum liquid temperature may be limited by local regulations and laws. 18

19 Pumped liquids TP, TPD, TPE, TPED List of pumped liquids Grundfos TP and TPD pumps are designed for circulation systems with constant flow; TPE and TPED pumps for systems with variable flow. Thanks to their design, the pumps can be used in a wider liquid temperature range than pumps of the canned rotor type. A number of typical liquids are listed below. Other pump versions may be used, but we consider the ones stated in the list to be the best choices. The list is intended as a general guide only, and it cannot replace actual testing of the pumped liquids and pump materials under specific working conditions. If in doubt, contact Grundfos. Use the list with some caution, as factors such as concentration of the pumped liquid, liquid temperature or pressure may affect the chemical resistance of a specific pump version. Legend A B C D E F G H May contain additives or impurities that may cause shaft seal problems. The density and/or viscosity differ from those of water. Consider this when calculating motor and pump performance. The liquid must be oxygen-free (anaerobic). Risk of crystallisation/precipitation in the shaft seal. Insoluble in water. The shaft seal rubber parts must be replaced with FKM rubber. Bronze housing/impeller required. Risk of formation of ice on the standby pump. (The risk only applies to TP, TPE Series 2 pumps.) Pumped liquids Water Groundwater Notes Additional information Shaft seal TP Series 1 TP Series 2 TP Series 3 < +9 C BQQE AUUE BQQE > +9 C BUBE BUBE BAQE 1) BBQE 2) TP Series PN 1 BAQE TP Series PN 25 < +12 C BUBE 3) BUBE BAQE BAQE DBUE Boiler-feed water < +1 C BUBE BQBE/DAQF 2) DBUE < +1 C DBUE District heating water < +12 C BUBE BUBE BAQE BAQE DBUE Condensate Softened water Brackish water Coolants Ethylene glycol B, D, H < + C, % Glycerine (glycerol) B, D, H < + C, % Potassium acetate B, D, C, H < + C, % Potassium formate B, D, C, H < + C, % Propylene glycol C G B, D, H Brine-sodium chloride B, D, C, H < +5 C, 3 % Synthetic oils Silicone oil B, E < +9 C BQQE AUUE BQQE > +9 C BUBE BUBE BAQE < +9 C BQQE AUUE BQQE > +9 C BUBE BUBE BAQE ph > 6.5, + C, 1 ppm Cl - BUBE BQQE BQQE GQQE BQQE GQQE BQQE GQQE BQQE GQQE BQQE GQQE BQQE GQQE BUBE BQQE BUBE AUUE AUUE RUUE AUUE RUUE AUUE RUUE AUUE RUUE AUUE RUUE AUUE RUUE BUBE AUUE BAQE BAQE DBUE DBUE DBUE BQQE BQQE DBUE BQQE GQQE BQQE GQQE BQQE GQQE BQQE GQQE BQQE GQQE BQQE GQQE BAQE BQQE GQQE DQQE 2) GQQE DQQE 2) GQQE DQQE 2) GQQE DQQE 2) GQQE DQQE 2) GQQE DQQE 2) BAQE DBUE (To be continued) 19

20 Pumped liquids TP, TPD, TPE, TPED Pumped liquids Vegetable oils Corn oil 1) BAQE must not be used for potable water. For potable water, Grundfos recommends a BBQE shaft seal. 2) The shaft seal is not standard, but available on request. 3) Maximum +11 C. B, F, E Olive oil B, F, E < +8 C Peanut oil Rape seed oil Soya bean oil Cleaning agents B, F, E D, B, F, E B, F, E Soap (salts of fatty acids) A, E, (F) < +8 C Alkaline degreasing agent A, E, (F) < +8 C Oxidants Notes Additional information Hydrogen peroxide < + C, < 2 % BUBV 2) BQQV 2) BUBV 2) BQQV 2) BUBV 2) AUUV 2) BUBV 2) AUUV 2) BAQV 2) BQQV 2) BAQV 2) BQQV 2) BAQV 2) DBUV 2) BAQV 2) DBUV 2) BUBV 2) BUBV 2) BAQV 2) BQQV 2) AUUV 2) BQQV 2) BAQV 2) DBUV 2) BUBV 2) BQQV 2) BUBV 2) AUUV 2) BAQV 2) BQQV 2) BAQV 2) DBUV 2) BUBV 2) BUBV 2) BAQV 2) BQQV 2) AUUV 2) BQQV 2) BAQV 2) DBUV 2) BQQE (BQQV) 2) BQQE (BQQV) 2) BUBE BQQE AUUE (AUUV) 2) AUUE (AUUV) 2) BUBE AUUE Shaft seal TP Series 1 TP Series 2 TP Series 3 BQQE (BQQV) 2) GQQE DQQE 2) BQQE (BQQV) 2) TP Series PN 1 TP Series PN 25 GQQE DQQE 2) BQQE BQQV 2) DQQE 2) Salts Ammonium bicarbonate A < +2 C, < 15 % BQQE AUUE BQQE GQQE DQQE 2) Calcium acetate A, B < +2 C, < 3 % BQQE AUUE BQQE GQQE DQQE 2) Potassium bicarbonate A < +2 C, < 2 % BQQE AUUE BQQE GQQE DQQE 2) Potassium carbonate A < +2 C, < 2 % BQQE AUUE BQQE GQQE DQQE 2) Potassium permanganate A < +2 C, < 1 % BQQE AUUE BQQE GQQE DQQE 2) Potassium sulphate A < +2 C, < 2 % BQQE AUUE BQQE GQQE DQQE 2) Sodium acetate A < +2 C, < 1 % BQQE AUUE BQQE GQQE DQQE 2) Sodium bicarbonate A < +2 C, < 2 % BQQE AUUE BQQE GQQE DQQE 2) Sodium carbonate A < +2 C, < 2 % BQQE AUUE BQQE GQQE DQQE 2) Sodium nitrate A < +2 C, < % BQQE AUUE BQQE GQQE DQQE 2) Sodium nitrite A < +2 C, < % BQQE AUUE BQQE GQQE DQQE 2) Sodium phosphate (di) A < +1 C, < 3 % BQQE AUUE BQQE GQQE DQQE 2) Sodium phosphate (tri) A < +9 C, < 2 % BQQE AUUE BQQE GQQE DQQE 2) Sodium sulphate A < +2 C, < 2 % BQQE AUUE BQQE GQQE DQQE 2) Sodium sulphite A < +2 C, < 1 % BQQE AUUE BQQE GQQE DQQE 2) Alkalis Ammonium hydroxide < +1 C, < 3 % BQQE AUUE BQQE GQQE DQQE 2) Calcium hydroxide A < +1 C, < 1 % BQQE AUUE BQQE GQQE DQQE 2) Potassium hydroxide A < +2 C, < 2 % BQQE AUUE BQQE GQQE DQQE 2) Sodium hydroxide A < + C, < 2 % BQQE AUUE BQQE GQQE DQQE 2) 2

21 TP Series 1 and 2 pumps TP, TPD, TPE, TPED Materials TP Series 1 Fig. 2 TP Series 1 and TP Series 2 Technical data Flow rate: Up to 9 m 3 /h Head: Up to 27 m Liquid temperature (TP Series 1): -25 to +11 C Liquid temperature (TP Series 2): -25 to +1 C Maximum operating pressure: Up to 16 bar Direction of rotation: Counter-clockwise Construction Grundfos TP Series 1 and Series 2 pumps are single-stage, close-coupled pumps with in-line suction and discharge ports of identical diameter. The pumps are fitted with a fan-cooled asynchronous motor. Motor and pump shafts are connected via a rigid two-part coupling. TP Series 1 pumps with union connection are available as single-head (TP) pumps. TP Series 2 pumps are available as single-head (TP) and twin-head (TPD) pumps. TP Series 2 pumps have PN 6 or PN 1 flanges. The pumps are fitted with an unbalanced mechanical shaft seal. The pumps are of the top-pull-out design, i.e. the power head (motor, pump head and impeller) can be removed for maintenance or service while the pump housing remains in the pipework. The twin-head pumps are designed with two parallel power heads. A non-return flap valve in the common discharge port is opened by the flow of the pumped liquid and prevents backflow of liquid into the idle pump head. As radial and axial forces are absorbed by the fixed bearing in the motor drive-end, the pump requires no bearing. TP, TPD Series 1 and 2 pumps are fitted with highefficiency motors. Pumps with bronze pump housing (version B) are suitable for circulation of domestic hot water. Gr Gr8261 Fig. 3 Sectional drawing of TP Series 1 (with union connection) Material specification, Series 1 Pos. Component Material EN/DIN 1 Pump housing TP, TPE Series 2 Cast iron EN-GJL-2, bronze CuSn1 Fig. Sectional drawing of TP Series 2 (with flange connection) TM EN-JL Impeller Stainless steel Shaft Stainless steel 1.57 Coupling Cast iron EN-GJL-.7 5 Pump head Secondary seals Rotating seal face Stationary seat Cast iron EN-GJL-2, bronze EPDM Tungsten carbide Silicon carbide Carbon (resin-impregnated) Silicon carbide TM

22 TP Series 1 and 2 pumps TP, TPD, TPE, TPED Material specification, Series 2 Pos. Component Material EN/DIN 1 Pump housing Mechanical shaft seal Three types of unbalanced mechanical shaft seal are available as standard: BUBE The BUBE shaft seal is a Grundfos rubber bellows seal with tungsten carbide/carbon seal faces and secondary seals of EPDM. RUUE/GQQE The RUUE shaft seal is a Grundfos O-ring seal with reduced tungsten carbide/tungsten carbide seal faces and secondary seals of EPDM. The GQQE shaft seal is a Grundfos rubber bellows seal with reduced silicon carbide/silicon carbide seal faces and secondary seals of EPDM. AUUE/BQQE The AUUE shaft seal is a Grundfos O-ring seal with fixed seal driver, tungsten carbide/tungsten carbide seal faces and secondary seals of EPDM. The BQQE shaft seal is a Grundfos rubber bellows seal with silicon carbide/silicon carbide seal faces and secondary seals of EPDM. Information on a selection of common pumped liquids with recommended shaft seals is shown on page 19. Shaft seal specification Cast iron EN-GJL-2, bronze CuSn1 EN-JL Impeller Stainless steel Shaft Stainless steel 1.35 Coupling Cast iron EN-GJL-.7 5 Pump head Secondary seals Rotating seal face Stationary seat Unbalanced shaft seal Shaft diameter Rubber bellows Seal faces Cast iron EN-GJL-2, bronze EPDM Tungsten carbide Carbon (resin-impregnated) Tungsten carbide TP Series 1 TP, TPD Series Version KU according to EN Version NU according to EN and 16 mm EPDM Tungsten carbide/carbon Tungsten carbide/tungsten carbide Silicon carbide/silicon carbide Special shaft seals are available for partly conditioned water or other liquids containing abrasive or crystallising particles. See page 19. Connections TP Series 1 pumps with union connection have suction and discharge union threads to ISO TP Series 2 pumps up to DN 65 are fitted with combination flanges PN 6/PN 1. DN 8 or DN 1 pumps have either PN 6 or PN 1 flanges. All flanges can be connected to flanges in accordance with EN and ISO Features and benefits TP Series 1 and Series 2 pumps have these features and benefits: Optimised hydraulics for high efficiency - Reduced power consumption. High-efficiency motors - TP pumps are fitted with high-efficiency motors. High-efficiency motors offer reduced energy consumption. TP pumps are primarily fitted with motors that meet the legislative requirements of the EuP IE3 grade. For further information, see section Motors on pages 36 to. Top-pull-out design - Easy dismantling in case of service. In-line design - Contrary to end-suction pumps, in-line pumps allow a straight pipework and thus often reduced installation costs. Pump housing and pump head are electrocoated to improve the corrosion resistance - Electrocoating includes: 1. Alkaline cleaning. 2. Pretreatment with zinc phosphate coating. 3. Cathodic electrocoating (epoxy).. Curing of paint film at 2-2 C. For low-temperature applications at a high humidity, Grundfos offers TP pumps with extra surface treatment to avoid corrosion. These pumps are available on request. Stainless-steel impeller and neck ring - Wear-free operation with high efficiency. TPE, TPED - pumps with built-in frequency converter - 2-pole and -pole TP pumps from.37 and upwards are available as TPE pumps with built-in frequency converter. See pages and

23 TP Series 3 pumps TP, TPD, TPE, TPED TP Series 3 pumps with bronze impeller are suitable for pumping brine. Materials Fig. 5 TP Series 3 Gr8259 TM Technical data Flow rate: Up to 825 m 3 /h Head: Up to 93 m Liquid temperature: -25 to +1 C Maximum operating pressure: 16 bar Direction of rotation: Clockwise Construction Grundfos TP, TPD Series 3 pumps are single-stage, close-coupled pumps with in-line suction and discharge ports of identical diameter. The pumps are fitted with a fan-cooled asynchronous motor. Motor and pump shafts are connected via a rigid sleeve coupling. Most TP Series 3 pumps are available as singlehead (TP) and twin-head (TPD) pumps. TP Series 3 pumps have PN 16 flanges. The pumps are fitted with an unbalanced mechanical shaft seal. The pumps are of the top-pull-out design, i.e. the power head (motor, pump head and/or motor stool and impeller) can be removed for maintenance or service while the pump housing remains in the pipework. The pump housing is provided with replaceable wear rings to ensure high pump efficiency for life. The twin-head pumps are designed with two parallel power heads. A non-return flap valve in the common discharge port is opened by the flow of the pumped liquid and prevents backflow of liquid into the idle pump head. As radial and axial forces are absorbed by the fixed bearing in the motor drive-end, the pump requires no bearing. The impeller is hydraulically balanced to minimise axial forces. TP, TPD Series 3 pumps are fitted with highefficiency motors. Fig. 6 Sectional drawing of TP Series 3 Material specification Pos. Component Material EN/DIN 1 Pump housing Cast iron EN-GJL-2 EN-JL 1 2 Impeller 3 Stub shaft Two-part stub shaft Pump head/motor stool Secondary seals Mechanical shaft seal Three types of unbalanced mechanical shaft seal are available as standard: BAQE The BAQE shaft seal is a Grundfos rubber bellows seal with carbon/silicon carbide seal faces and secondary seals of EPDM. GQQE The GQQE shaft seal is a Grundfos rubber bellows seal with reduced silicon carbide/silicon carbide seal faces and secondary seals of EPDM. BQQE The BQQE shaft seal is a Grundfos rubber bellows seal with silicon carbide/silicon carbide seal faces and secondary seals of EPDM. Information on a selection of common pumped liquids with recommended shaft seals is shown on page 19. Shaft seal specification Cast iron EN-GJL-2, bronze CuSn5Zn5Pb Stainless steel Stainless steel/steel EN-JL /1.31 Cast iron EN-GJL-2 EN-JL 1 EPDM Metal-impregnated Rotating seal face carbon Silicon carbide Stationary seat Silicon carbide 5 Wear rings Bronze CuSn Unbalanced shaft seal Version NU according to EN Shaft diameter 28, 38, 8 and 55 mm Rubber bellows EPDM Seal faces Carbon/silicon carbide Silicon carbide/silicon carbide 23

24 TP Series 3 pumps TP, TPD, TPE, TPED Special shaft seals are available for partly conditioned water or other liquids containing abrasive or crystallising particles. See page 19. Connections TP Series 3 pumps have PN 16 flanges. All dimensions are according to ISO 75-2 or EN Features and benefits TP Series 3 pumps have these features and benefits: Optimised hydraulics for high efficiency - Reduced power consumption. High-efficiency motors - TP pumps are fitted with high-efficiency motors. High-efficiency motors offer reduced energy consumption. TP pumps are primarily fitted with motors that meet the legislative requirements of the EuP IE3 grade. For further information, see section Motors on pages 36 to. Top-pull-out design - Easy dismantling in case of service. In-line design - Contrary to end-suction pumps, in-line pumps allow a straight pipework and thus often reduced installation costs. Motor-pump shaft with sleeve coupling - - Stable and quiet operation. Easy dismantling in case of service. Hydraulically and mechanically balanced impeller - The impeller is hydraulically and mechanically balanced to increase the life of motor bearings and shaft seal. Pump housing and pump head/motor stool are electrocoated to improve the corrosion resistance - Electrocoating includes: 1. Alkaline cleaning. 2. Pretreatment with zinc phosphate coating. 3. Cathodic electrocoating (epoxy).. Curing of paint film at 2-2 C. For low-temperature applications at a high humidity, Grundfos offers TP pumps with extra surface treatment to avoid corrosion. These pumps are available on request. TPE, TPED - pumps with built-in frequency converter - 2-pole TP pumps from.37 to 22 kw and -pole TP pumps from.37 to 18.5 kw are available as TPE pumps with built-in frequency converter. See pages and

25 TP Series pumps TP, TPD, TPE, TPED TP Series pumps are fitted with high-efficiency motors. Materials Gr7539 TM Fig. 7 TP Series Technical data Flow rate: PN 1 version: PN 25 version: Head: PN 1 version: PN 25 version: Liquid temperature: PN 1 version: PN 25 version: Up to 9 m 3 /h Up to m 3 /h Up to 38 m Up to 17 m -25 to +12 C to +1 C * * From +12 to +1 C, max. 23 bar Maximum operating pressure: 1 bar version: 25 bar version: Direction of rotation: Clockwise 1 bar 25 bar Construction Grundfos TP Series pumps are single-stage, closecoupled pumps with in-line suction and discharge ports. The pumps are fitted with a fan-cooled asynchronous motor. Motor and pump shafts are connected via a rigid flange coupling. TP Series pumps are available as single-head (TP) pumps. All TP Series pumps have PN 1 or PN 25 flanges. The largest pumps have DN, PN discharge flanges and a maximum operating pressure of 25 bar. Fig. 8 Sectional drawing of TP Series Material specification TP Series, PN 1 Pos. Component Material EN/DIN 1 Pump housing Cast iron EN-GJL-2 EN-JL1 2 Impeller Ductile cast iron EN-GJS- EN-JL13 Bronze Pump shaft Stainless steel 1.36 Coupling Cast iron EN-GJL-2 EN-JL1 5 Motor stool Cast iron EN-GJL-2 EN-JL1 Secondary seals EPDM rubber Metal-impregnated carbon Rotating seal face Silicon carbide Stationary seat Silicon carbide 6 Wear rings Bronze CuSn TP Series, PN 25 Pos. Component Material EN/DIN 1 Pump housing Ductile cast iron EN-GJS--18 (A-LT) EN-JS12 2 Impeller Ductile cast iron EN-GJS- EN-JS13 Bronze Pump shaft Stainless steel 1.36 Coupling Cast iron EN-GJL-2 EN-JL1 5 Motor stool Cast iron EN-GJL-2 EN-JL1 Secondary seals EPDM rubber Rotating seal face Resin-impregnated carbon Stationary seat Tungsten carbide The pumps are fitted with an unbalanced mechanical shaft seal. The pumps are of the top-pull-out design, i.e. the power head (motor, motor stool and impeller) can be removed for maintenance or service while the pump housing remains in the pipework. The pump housing is provided with replaceable wear rings to ensure high pump efficiency for life. As radial and axial forces are absorbed by the fixed bearing in the motor drive-end, the pump requires no bearing. 25

26 TP Series pumps TP, TPD, TPE, TPED Mechanical shaft seal For 1 bar versions, the following three types of unbalanced mechanical shaft seal are available as standard: BAQE The BAQE shaft seal is a Grundfos rubber bellows seal with carbon/silicon carbide seal faces and secondary seals of EPDM. GQQE The GQQE shaft seal is a Grundfos rubber bellows seal with reduced silicon carbide/silicon carbide seal faces and secondary seals of EPDM. BQQE The BQQE shaft seal is a Grundfos rubber bellows seal with silicon carbide/silicon carbide seal faces and secondary seals of EPDM. For 25 bar versions, the following mechanical shaft seal is available as standard: DBUE The DBUE shaft seal is a Grundfos balanced O-ring seal with carbon/tungsten carbide seal faces and secondary seals of EPDM. Information on a selection of common pumped liquids with recommended shaft seals is shown on page 19. Special shaft seals are available for partly conditioned water or other liquids containing abrasive or crystallising particles. See page 19. Connections TP Series pumps are the only TP pumps with suction and discharge ports of different diameters. The suction port is one dimension larger than the discharge port in order to obtain a low inlet velocity. This reduces risk of cavitation and noise. From DN 1 to DN 3 TP Series pumps have flanges according to ISO 75-2 or EN Features and benefits TP Series pumps have the following features and benefits: Optimised hydraulics for high efficiency - Reduced power consumption. High-efficiency motors - TP pumps are fitted with high-efficiency motors. High-efficiency motors offer reduced energy consumption. TP pumps are primarily fitted with motors that meet the legislative requirements of the EuP IE3 grade. For further information, see section Motors on pages 36 to. Top-pull-out design - Easy dismantling in case of service. In-line design - Contrary to end-suction pumps, in-line pumps allow a straight pipework and thus often reduced installation costs. Motor-pump shaft with flange coupling - - Stable and quiet operation. Easy dismantling in case of service. Supported flange connection - Pump housing flanges have integrated feet in order to stabilise the pump. Surface treatment TP Series pumps are given the following surface treatment: Pump type Electrocoating Spray painting TP Series (from DN 1 to DN 3) x x TP Series (DN ) 2x Electrocoating includes: 1. Alkaline cleaning. 2. Pretreatment with zinc phosphate coating. 3. Cathodic electrocoating (epoxy).. Curing of paint film at 2-2 C. For low-temperature applications at a high humidity, Grundfos offers TP pumps with extra surface treatment to avoid corrosion. These pumps are available on request. 26

27 TPE Series 1 pumps TP, TPD, TPE, TPED Fig. 9 TPE and TPED Series 1 TM Applications TPE Series 1 pumps have integrated speed control for automatic adaptation of performance to current conditions. The energy consumption is thus kept at a minimum. TPE Series 1 pumps can operate in any duty point within the range between 25 % and 1 % speed (11 to 22 kw TPE(D) pumps up to 11 % speed). H H 1 % Technical data Flow rate: Up to 3 m 3 /h Head: Up to 9 m Liquid temperature: -25 to +1 C Maximum operating pressure: 16 bar Motor sizes (single-phase):.37 to 1.1 kw Motor sizes (three-phase):.55 to 22 kw Construction TPE, TPED Series 1 pumps are based on TP, TPD Series 1, 2 and 3 pumps. The main difference between the TP and the TPE Series 1 pump range is the motor. The motor of TPE Series 1 pumps has a built-in frequency converter for continuous adjustment of the pressure to the flow rate. TPE Series 1 pumps are suitable for applications where the pressure, temperature, flow rate or another parameter is to be controlled on the basis of signals from a sensor at some point in the system. Note: TPE Series 1 pumps are not fitted with a sensor from factory. For further information on construction and materials of TPE Series 1 pumps, see pages 21 to % Q [m 3 h] Q [m³/h] Fig. 1 Duty range of TPE Series 1 pumps The 1 % curve corresponds to the curve of a pump with a mains-operated motor. Depending on the application, TPE Series 1 pumps offer energy savings, increased comfort or improved processing. The pumps can be fitted with sensor types meeting the requirements mentioned in the data booklet titled "Grundfos E-pumps". TM

28 TPE Series 1 pumps TP, TPD, TPE, TPED The charts below show possible control modes of TPE Series 1 pumps in different applications. Control mode Constant curve Application Single-pipe heating systems. Systems with three-way valves. Heating and cooling surfaces. Chiller pumps. Constant differential pressure Systems with two-way valves. (Sensor is needed.) Temperature control Constant flow rate Single-pipe heating systems. Systems with three-way valves. Cooling towers. Chiller pumps. Domestic hot-water recirculation systems. (Sensor is needed.) Heating and cooling surfaces. Cooling towers. Flow filters. (Sensor is needed.) Proportional differential pressure (measured) System with two-way valves. (The differential pressure sensor is located in the system.) TPE(D) pumps with extended performance range Standard TPE(D) pumps, Hz, with motors from 11 to 22 kw are able to operate in a range above the 1 % curve. See fig. 11. The extended range is provided by means of optimised software which utilises the MGE motor in an optimum way. The result is that the TPE(D) pump is able to deliver higher head and flow with the same motor size. The curve sheets in the TP, TPD, TPE, TPED data booklet are only showing the nominal 1 % Q-H curve. WinCAPS and WebCAPS are showing the extended performance range of the 11 to 22 kw TPE(D) pumps. Operating modes of twin-head pumps The following operating modes are available for twinhead pumps: Alternating operation The two pumps run alternately for 2 operating hours. In case of fault in the operating pump, the other pump will start. Standby operation One pump is in constant operation. Every 2 operating hours the standby pump will start and run for a short period to prevent it from seizing up. In case of fault in the operating pump, the standby pump will start. The operating mode is selected by means of a selector switch in each terminal box. In case of sensor fault, the operating pump will switch to maximum operation. Control options Communication with TPE, TPED Series 1 pumps is possible via a central building management system, remote control (Grundfos R1) or control panel. The purpose of controlling a TPE, TPED Series 1 pump is to monitor and control the pressure, temperature, flow rate and liquid level of the system. For further information on control options of TPE pumps, see page 31. H (m) 11 % 6 1 % TPE -57/2-S 19 % 17 % 15 % 13 % 3 x V, Hz Q = 5.1 m 3 /h H = 5 m n = 1 % 11 % 1 % Q(m3/h) TM Fig to 22 kw TPE(D) pumps with extended performance range 28

29 TPE Series 2 pumps TP, TPD, TPE, TPED Applications TPE Series 2 pumps have integrated speed control for automatic adaptation of performance to current conditions. The energy consumption is kept thus at a minimum. TM TPE Series 2 pumps can operate in any duty point within the range between 25 % and 1 % speed (11 to 22 kw TPE(D) pumps up to 11 % speed). H Fig. 12 TPE Series 2 1 % Technical data Flow rate: Up to 3 m 3 /h Head: Up to 9 m Liquid temperature: -25 to +1 C Maximum operating pressure: 16 bar Motor sizes (single-phase):.37 to 1.1 kw Motor sizes (three-phase):.55 to 22 kw 25 % Q [m³/h] [m 3 h] TM Construction TPE, TPED Series 2 pumps are based on TP, TPD Series 2 and 3 pumps. The main differences between the TP and the TPE Series 2 pumps are the motor and the factory-fitted differential pressure sensor. The motor of TPE Series 2 pumps has built-in frequency converter for continuous adjustment of the pressure to the flow rate. The TPE Series 2 range is a preset solution for quick and safe installation. For further information on construction and materials of TPE Series 2 pumps, see pages 21 to 2. Fig. 13 Duty range of TPE Series 2 pumps The 1 % curve corresponds to the curve of a pump with a mains-operated motor. Depending on the application, TPE Series 2 pumps offer energy savings, increased comfort or improved processing. TPE Series 2 pumps are suitable for applications requiring pressure control. Proportional pressure TPE Series 2 pumps are factory-set to proportional pressure control. We recommend proportional pressure control in systems with relatively large pressure losses, as it is the most economical control mode. TPE Series 2 pumps set to proportional pressure control continuously adjust the pump head to the water requirement of the system. The setpoint is factory-set to % of the maximum pump head. The pumps can be retrofitted with sensor types meeting the requirements mentioned in the data booklet titled Grundfos E-pumps. 29

30 TPE Series 2 pumps TP, TPD, TPE, TPED The charts below show possible control modes of TPE Series 2 pumps in different applications. Control mode Proportional pressure Application Systems with two-way valves. - The head against a closed valve is % of the setpoint. Operating modes of twin-head pumps The following operating modes are available for twinhead pumps: Alternating operation The two pumps run alternately for 2 operating hours. In case of fault in the operating pump, the other pump will start. Constant pressure Systems with two-way valves. Standby operation One pump is in constant operation. Every 2 operating hours the standby pump will start and run for a short period to prevent it from seizing up. In case of fault in the operating pump, the standby pump will start. The operating mode is selected by means of a selector switch in each terminal box. Constant curve Single-pipe heating system. Systems with three-way valves. Heating and cooling surfaces. Chiller pumps. TPE(D) pumps with extended performance range Standard TPE(D) pumps, Hz, with motors from 11 to 22 kw are able to operate in a range above the 1 % curve. See fig. 1. In case of sensor fault, the operating pump will switch to maximum operation. Control options Communication with TPE, TPED Series 2 pumps is possible via a central building management system, remote control (Grundfos R1) or control panel. The purpose of controlling TPE, TPED Series 2 pumps is to monitor and control the pressure, temperature, flow rate and liquid level of the system. For further information on control options of TPE pumps, see page 31. H (m) 11 % 6 1 % TPE -57/2-S 19 % 17 % 15 % 13 % 3 x V, Hz Q = 5.1 m 3 /h H = 5 m n = 1 % 11 % 1 % Q(m3/h) TM Fig to 22 kw TPE(D) pumps with extended performance range The extended range is provided by means of optimised software which utilises the MGE motor in an optimum way. The result is that the TPE(D) pump is able to deliver higher head and flow with the same motor size. The curve sheets in the TP, TPD, TPE, TPED data booklet are only showing the nominal 1 % Q-H curve. WinCAPS and WebCAPS are showing the extended performance range of the 11 to 22 kw TPE(D) pumps. 3

31 Communication TP, TPD, TPE, TPED Communication with TPE, TPED pumps Communication with TPE, TPED pumps is possible via a central building management system, remote control (Grundfos R1) or control panel. Central building management system The operator can communicate with a TPE, TPED pump at a distance. Communication can take place via a central building management system allowing the operator to monitor and change control modes and setpoint settings. Remote control The Grundfos R1 remote control is available as an accessory. The operator can communicate with the TPE, TPED pump by pointing the IR-signal transmitter at the control panel of the terminal box. TM LON, Profibus, Modbus, Bnet network or GSM/GPRS network Fig. 16 R1 remote control The operator can monitor and change control modes and settings of the TPE, TPED pump via the R1 display. Control panel The operator can change the setpoint settings manually on the control panel of the TPE, TPED pump terminal box. CIU 1: LON CIU 1: Profibus DP CIU 2: Modbus RTU CIU 2: GSM/GPRS CIU 3: Bnet MS/TP TM 76 Fig. 17 Control panel of a TPE pump CIM 1: LON CIM 1: Profibus DP CIM 2: Modbus RTU CIM 2: GSM/GPRS CIM 3: Bnet MS/TP TPE pump TPE pump (11-22 kw) TM Fig. 15 Structure of a central building management system 31

32 Speed regulation of TPE pumps TP, TPD, TPE, TPED Affinity equations Normally, TPE, TPED pumps are used in applications characterised by a variable flow. Consequently, it is not possible to select a pump that is constantly operating at its optimum efficiency. H H n Q n n n = Q x n x In order to achieve optimum operating economy, the duty point should be close to the optimum efficiency (eta) for most operating hours. H x n x n n H n n n 2 = H x n x Between the min. and max. performance curves, TPE, TPED pumps have an infinite number of performance curves each representing a specific speed. It may therefore not be possible to select a duty point close to the max. curve. Eta Q x Q n Q η n 1 η x H n x n n Max. curve P n P Q x Q n n n Q P n n n = P x n x Min. curve Q [m [m³/h] 3 h] Fig. 18 Min. and max. performance curves In situations where it is not possible to select a duty point close to the max. curve, use the affinity equations below. The head (H), the flow rate (Q) and the input power (P) are the appropriate variables you need for calculating the motor speed (n). Note: The approximated formulas apply on condition that the system characteristic remains unchanged for n n and n x, and that it is based on the formula H = k x Q 2 where k is a constant. The power equation implies that the pump efficiency is unchanged at the two speeds. In practice this is not quite correct. Finally, it is worth noting that the efficiency of the frequency converter and the motor must be taken into account if a precise calculation of the power saving resulting from a reduction of the pump speed is wanted. TM P x Fig. 19 Affinity equations Legend H n Rated head in metres H x Current head in metres Q n Rated flow rate in m 3 /h Q x Current flow rate in m 3 /h n n Rated motor speed in min -1 n x Current motor speed in min -1 η n Rated efficiency in % η x Current efficiency in % WinCAPS and WebCAPS WinCAPS and WebCAPS are selection programs offered by Grundfos. n x The two programs make it possible to calculate the specific duty point and energy consumption of a TPE pump. When you enter the dimensions of the pump, WinCAPS and WebCAPS can calculate the exact duty point and energy consumption. For further information, see page 13. Q TM

33 TP, TPE pumps in parallel TP, TPD, TPE, TPED Control of TP, TPE pumps connected in parallel In some applications parallel pump operation is required for one or more of the following reasons: One pump cannot achieve the required performance (flow rate). Standby capacity is required to ensure reliability of supply. Overall efficiency needs to be improved in case of big variations in the flow demand. The table below lists the different possibilities of controlling TP, TPE pumps connected in parallel. Parallel-operation control possibilities Built-in alternation/standby function TP, TPE TPE Series 2 1) 1) TP, TPE pumps connected to Control MPC TP, TPE pumps can be connected directly to Grundfos Control MPC. Control MPC incorporates a CU 351 controller that can control up to six pumps. By means of an external sensor Control MPC can ensure optimum adaptation of the performance to the demand by closed-loop control of these parameters: proportional differential pressure constant differential pressure differential pressure (remote) flow rate temperature. The CU 351 incorporates features such as those below: Start-up wizard Correct installation and commissioning is a prerequisite for attaining optimum performance of the system and trouble-free operation year in and year out. Control MPC Control MPC Series 2 During commissioning of the system, a start-up wizard is shown on the display of the CU 351. The wizard will guide the operator through the various steps via a series of dialogue boxes to ensure that all settings are done in the correct sequence. Application-optimised software The CU 351 incorporates application-optimised software which helps you set up your system to the application in question. Available. 1) Applies only to TPED pumps. Alternation/standby function of TPED pumps All TPED pumps have built-in alternation/standby function. The pumps are supplied with a special cable for the communication between the two power heads. The function is activated from factory and "alternating" mode is selected as default. See pages 28 and 3. Fig. 2 TPED Series 2 TM3 13 Furthermore, navigating through the menus of the controller is done in a user-friendly way. You do not need any training to be able to set and monitor the system. Ethernet connection The CU 351 incorporates an Ethernet connection which makes it possible to get full and unlimited access to the setting and monitoring of the system via a remote PC. Service port (GENI TTL) The service port of the CU 351 enables easy access to updating software and data logging in service situations. External communication Control MPC enables communication with other fieldbus protocols. In order to communicate with other fieldbus protocols, a GENIbus module and a gateway are required. Control MPC can communicate with LON, Profibus, Modbus, Bnet, GSM/GPRS or GRM via a Grundfos CIU. 33

34 TP, TPE pumps in parallel TP, TPD, TPE, TPED TPE Series 2 pumps connected to Control MPC Series 2 TPE Series 2 pumps are connected directly to Grundfos Control MPC Series 2 via GENIbus. Control MPC Series 2 incorporates a CU 351 controller that can control up to six pumps. All pumps must be of the same type and size. Control MPC Series 2 is used for controlling circulator pumps in heating and air-conditioning applications. Control MPC Series 2 ensures optimal adaptation of the performance to the demand by closed-loop control of these parameters: proportional differential pressure constant differential pressure. By means of an external sensor Control MPC Series 2 can also ensure optimum adaptation of the performance to the demand by closed-loop control of these parameters: differential pressure (remote) flow rate temperature. Note: For further information about Control MPC and Control MPC Series 2, see the data booklet titled "Control MPC". The data booklet is available in WebCAPS, on For further information on WebCAPS, see page 13. 3

35 Grundfos CUE TP, TPD, TPE, TPED TP pumps connected to Grundfos CUE, external frequency converters Functions Intuitive start-up guide The start-up guide enables easy installation and commissioning as well as plug-and-pump convenience. Few settings need to be made by the installer as the rest is done automatically or preset from the factory. Smart user interface Fig. 21 Grundfos CUE Grundfos CUE is a complete range of wall-mounted frequency converters for pump control in a wide range of applications. Grundfos CUE provides a variety of benefits, such as these: Grundfos E-pump functionality and user interface application- and pump family-related functions increased comfort compared to fixed-speed pump solutions simple installation and commissioning compared to standard frequency converters speed control of pumps up to 2 kw. GrA Fig. 22 Grundfos CUE user interface Grundfos CUE features a unique user-friendly control panel with graphic display and easy-to-use buttons. Panel layout resembles the well-known Grundfos R1 remote control, which is used with Grundfos E-pumps. Controlling the value you choose Grundfos CUE has a built-in PI controller offering closed-loop control of a desired value, such as these: constant differential pressure proportional pressure constant temperature constant differential pressure constant flow rate. TM Wide product range The CUE product range is quite comprehensive, covering five different voltage ranges, enclosure classes I/21 (Nema 1) and IP5/55 (Nema 12), and a wide range of output powers. The table below provides a general overview. Input voltage [V] Output voltage [V] Motor 1 x x x x x 38-3 x x x x x External communication Grundfos CUE can communicate with LON, Profibus, Modbus, Bnet or GSM/GPRS via a Grundfos CIU. 35

36 Motor data TP, TPD, TPE, TPED Motors Motors fitted on TP pumps are totally enclosed, fancooled motors with main dimensions to IEC and DIN standards. Electrical tolerances to IEC 3. Mounting designation Pump type Mounting designation - IEC 3-7 TP Series 1 TP Series 2 IM 361 (IM B 1) / IM 3611 (IM V 18) TP Series 3 IM 31 (IM B 5) / IM 311 (IM V 1) TP Series IM 31 (IM B 5) / IM 311 (IM V 1) Relative humidity: Max. 95 % Enclosure class: IP55 Insulation class: F, to IEC 85 Ambient temperature: Max. +55 C (IE2 and IE3 Siemens motors) Max +6 C (IE2 and IE3 MG motors) Max. + C (other motors) Min. -3 C If the pump is installed in humid locations, open the lowest drain hole in the motor. This will reduce the motor enclosure class to IP. High-efficiency motors TP pumps are fitted with high-efficiency motors. TP, TPD pumps with 2-pole three-phase motors from.75 to 75 kw are fitted with IE3 motors. TP, TPD pumps with -pole three-phase motors from.75 to 15 kw are fitted with IE3 motors. TP, TPD pumps with 2-pole three-phase motors of 9 kw are fitted with IE2 (EFF1) motors. TP, TPD pumps with -pole three-phase motors from 18.5 to 9 kw are fitted with IE2 (EFF1) motors. Motor range kw Electronically speedcontrolled motors Mains-operated motors 2-pole -pole 6-pole 2-pole -pole MEZ MG Siemens MEZ MG Siemens Siemens MGE MG and MGE are Grundfos motor brands. Siemens is a sourced high-quality motor brand. The grey-shaded areas indicate non-available motors. MGE TPE, TPED pumps with 2-pole three-phase motors from.75 to 22 kw are fitted with motors equivalent to IE3. TPE, TPED pumps with -pole three-phase motors from 1.1 to 15 kw are fitted with motors equivalent to IE2 (EFF1). TPE, TPED pumps with -pole three-phase motors of 18.5 kw are fitted with motors equivalent to IE1 (EFF2). 36

37 Motor data TP, TPD, TPE, TPED Motor protection MG, Siemens Single-phase motors have integrated, interconnected thermal switches. Three-phase motors must be connected to a motorprotective circuit breaker. All three-phase mains-operated motors can be connected to an external frequency converter. If you connect a frequency converter, the motor insulation system will often be overloaded, and the motor will be more noisy than in normal operation. In addition, large motors will be exposed to bearing currents caused by the frequency converter. If you operate the motor via a frequency converter, consider the following: In 2-, - and 6-pole motors of 5 kw (frame size 225) and upwards, isolate one of the motor bearings electrically to prevent damaging currents from passing through the motor bearings. If you have noise-sensitive applications, you can reduce the motor noise by fitting a du/dt filter between the motor and the frequency converter. For particularly noise-sensitive applications, we recommend a sinusoidal filter. The length of the cable between motor and frequency converter affects the motor load. Therefore, check that the cable length meets the specifications laid down by the frequency converter supplier. For supply voltages between and 69 V, fit either a du/dt filter to reduce voltage peaks, or use a motor with reinforced insulation. For supply voltages of 69 V, use a motor with reinforced insulation, and fit a du/dt filter. MGE MGE motors with built-in frequency converter do not require protection by a motor-protective circuit breaker. 37

38 Motor data TP, TPD, TPE, TPED Electrical data, mains-operated motors Electrical data, 2-pole 1 x 22-23/2 V Electrical data, 2-pole 3 x 38-15/66-69 V Motor I 1/1 [A] Cos φ 1/1 η [%] n [min -1 ] / / / / / / / /3.9 Electrical data, 2-pole Motor 3 x 22-2/38-15 V I 1/1 [A] Cos φ 1/1 η [%] n [min -1 ].12.59/ / / / / / / / / / / / / / / Electrical data, 2-pole 3 x 22-2/38-2 V Motor I 1/1 [A] Cos φ 1/1 η [%] n [min -1 ] / / / / / I Start I 1/1 I Start I 1/1 I Start I 1/ Motor I 1/1 [A] Cos φ 1/1 η [%] n [min -1 ] / / / Electrical data, 2-pole / / / / / / / / / / / Motor x 38-2/ V I 1/1 [A] Cos φ 1/1 η [%] n [min -1 ] / / / / / I Start I 1/1 I Start I 1/

39 Motor data TP, TPD, TPE, TPED Electrical data, -pole 1 x 22-23/2 V Electrical data, -pole 3 x 38-15/66-69 V Motor I 1/1 [A] Cos φ 1/1 η [%] n [min -1 ] Electrical data, -pole Motor 3 x 22-2/38-15 V I 1/1 [A] Cos φ 1/1 η [%] n [min -1 ].12.78/ / / / / / / / / / / / / / / / / I Start I 1/1 I Start I 1/ Motor I 1/1 [A] Cos φ 1/1 η [%] n [min -1 ] / / / / / / Electrical data, 6-pole / / / / / / / / / / / / / / / / / Motor 3 x 22-2/38-15 V I 1/1 [A] Cos φ 1/1 η [%] n [min -1 ] I Start I 1/1 I Start I 1/ / / / / / / Electrical data, 6-pole 3 x 38-15/66-69 V Motor I 1/1 [A] Cos φ 1/1 η [%] n [min -1 ] I Start I 1/ / / / / /

40 Motor data TP, TPD, TPE, TPED Electrical data, speed-controlled motors Electrical data, 2-pole 1 x 2-2 V, 29 min -1 Motor I 1/1 [A] Electrical data, 2-pole 3 x 38-8 V, 29 min -1 Motor I 1/1 [A] Electrical data, -pole 1 x 2-2 V, 1 min -1 Motor I 1/1 [A] Electrical data, -pole 3 x 38-8 V, 1 min -1 Motor I 1/1 [A]

41 Installation TP, TPD, TPE, TPED Mechanical installation TP, TPD, TPE, TPED pumps with motors smaller than 11 kw can be installed in horizontal or vertical pipework. Twin-head pump housings have two Rp 1/ tappings (TP Series 2) or four Rp 1/8 tappings (TP Series 3) for mounting of automatic air vents. Fig. 23 Installation of motor sizes smaller than 11 kw TP, TPD, TPE, TPED pumps with motors of 11 kw and up may only be installed in horizontal pipes with the motor in vertical position. TM Fig. 26 Tappings for mounting of automatic air vents in TP Series 2 and TP Series 3 For further information about identification of TP Series 2 and TP Series 3 models, see pages 21 to 23. If the liquid temperature falls below the ambient temperature, condensation may form in the motor during inactivity. In this case, the drain hole in the motor flange must be open and points downwards. See fig. 27. TM Fig. 2 Installation of motor sizes of 11 kw and up Note: The motor must never point downwards. Install the pumps in such a way that strain from the pipework is not transferred to the pump housing. Pumps with motors smaller than 11 kw may be suspended direct in the pipes, provided the pipework can support the pump. If not, install the pump on a mounting bracket or base plate. Pumps with motors of 11 kw and up may only be installed in horizontal pipes with the motor placed in vertical position. Always install the pump on an even and rigid foundation. When installing a twin-head pump in a horizontal pipe and with horizontal shaft, fit the upper pump housing with an automatic air vent. TM Fig. 27 Drain hole If twin-head pumps are used for pumping liquids with a temperature below C/32 F, condensed water may freeze and cause the coupling to get stuck. The problem can be remedied by installing heating elements. Whenever possible, pumps with motors smaller than 11 kw should be installed with horizontal motor shaft. See fig. 25. TM TM Fig. 25 Twin-head pumps with automatic air vent 1

42 Installation TP, TPD, TPE, TPED Cooling To ensure sufficient cooling of motor and electronics, observe the following: Place the pump in such a way that sufficient cooling is ensured. Make sure that the temperature of the cooling air does not exceed + C. Keep the motor cooling fins, holes in fan cover and fan blades clean. Make sure the frequency for the motor is at least 6 Hz (12 % of maximum speed). The shaft seal could make noise at speeds below 25 % of maximum speed. Condensation cover for TPE pumps When installing TPE pumps outdoors, provide the motor with a suitable cover to avoid condensation on the electronic components and to protect the pump and motor against the direct effects of the elements. When mounting the condensation cover on top of the motor, make sure to leave enough space for the air to cool the motor. Elimination of noise and vibrations In order to achieve optimum operation and minimum noise and vibration, consider vibration dampening of the pump. Generally, always consider this for pumps with motors of 11 kw and up, but for motors of 9 kw and up vibration dampening should be considered as mandatory. Smaller motor sizes, however, may also cause undesirable noise and vibration. Noise and vibration are generated by the revolutions of the motor and pump and by the flow in pipes and fittings. The effect on the environment is subjective and depends on correct installation and the state of the remaining system. Elimination of noise and vibrations is best achieved by means of a concrete foundation, vibration dampers and expansion joints. Concrete foundation Expansion joint Fig. 28 Speed-controlled motors with condensation cover TM Vibration dampers Fig. 29 Foundation of TP pump Concrete foundation Install the pump on a plane and rigid concrete foundation. This is the optimum solution for vibration dampening. As a rule of thumb, the weight of a concrete foundation should be 1.5 times the pump weight. TM

43 Installation TP, TPD, TPE, TPED Recommended concrete foundations for TP(D) Series 3 pumps For TP Series 3 pumps with weights of 1 kg or more, it is recommended to mount the pump on a concrete foundation with the dimensions stated in the table below. The same recommendation applies for TPD Series 3 pumps with weights of 3 kg or more. Fig. 3 Foundation for TP(D) Series 3 pumps TM Vibration dampers To prevent the transmission of vibrations to buildings, we recommend you to isolate the pump foundation from building parts by means of vibration dampers. The selection of the right vibration damper requires the following data: forces transmitted through the damper motor speed considering speed control, if any required dampening in % (suggested value is 7 %). Which is the right damper varies from installation to installation, and a wrong damper may increase the vibration level. Vibration dampers should therefore be sized by the supplier. If you install the pump on a foundation with vibration dampers, always fit expansion joints on the pump flanges. This is important to prevent the pump from "hanging" in the flanges. Pump mass [kg] Concrete foundation dimensions Y (height) [mm] Z (length) [mm] X (width) [mm]

44 Installation TP, TPD, TPE, TPED Expansion joints Install expansion joints to absorb expansions/contractions in the pipework caused by changing liquid temperature. reduce mechanical strains in connection with pressure surges in the pipework. isolate mechanical structure-borne noise in the pipework (only rubber bellows expansion joints). Note: Do not install expansion joints to compensate for inaccuracies in the pipework such as centre displacement of flanges. Fit expansion joints at a distance of minimum 1 to 1.5 times the nominal flange diameter away from the pump on the suction as well as on the discharge side. This will prevent the development of turbulence in the expansion joints, resulting in better suction conditions and a minimum pressure loss on the pressure side. At high water velocities (> 5 m/s) we recommend you to install larger expansion joints corresponding to the pipework. See fig. 31. The illustration below shows an example of a metal bellows expansion joint with limit rods. Fig. 33 Example of metal expansion joint Due to the risk of rupture of the rubber bellows, metal bellows expansion joints may be preferred at temperatures above +1 C combined with high pressure. TM Expansion joints Fig. 31 TP pump installed with larger expansion joints The illustration below shows examples of rubber bellows expansion joints with or without limit rods. TM TM TM Fig. 32 Examples of rubber bellows expansion joints Expansion joints with limit rods can be used to reduce the effects of the expansion/contraction forces on the pipework. We always recommend expansion joints with limit rods for flanges larger than DN 1. Anchor the pipes in such a way that they do not stress the expansion joints and the pump. Follow the supplier s instructions and pass them on to advisers or pipe installers.

45 Installation TP, TPD, TPE, TPED Terminal box positions TP single-head pumps As standard, the terminal boxes of TP and TPE pumps are mounted in position 9 o clock. The possible terminal box positions are shown below. 3 Stellung o clock 3 6 o clock 9 o clock Standard Stellung 6 Stellung 9 Stellung 12 Fig. 3 Possible terminal box positions 12 o clock Note: Due to the motor construction the terminal boxes of some TP pumps with motor sizes above 2 kw are mounted in position 1:3. TPD twin-head pumps As standard, the terminal boxes of all TPD and most TPED pumps are mounted in position 12 o clock. See fig. 3. The TPED pumps with terminal boxes installed in other positions are listed in the table. See example in fig. 35. Fig. 35 Terminal box positions of TPED pumps Note: The dimension can be seen in the tables of technical data of the individual pump. See the sections on performance curves and technical data. TM TM TPED pumps with terminal boxes installed in positions different from 12 o clock Single-phase Three-phase TPED 32-6/2.37 TPED 32-23/2.75 TPED 32-12/2.37 TPED 32-2/2 1.1 TPED -6/2.37 TPED 32-2/2 1.5 TPED -12/2.37 TPED 32-32/2 2.2 TPED -6/2.37 TPED 32-38/2 3. TPED 32-3/.37 TPED 32-6/2. TPED -3/.37 TPED 32-58/2 5.5 TPED -3/.37 TPED -19/2.75 TPED -23/2 1.1 TPED -27/2 1.5 TPED -2/2 2.2 TPED -3/2 3. TPED -36/2. TPED -7/2 5.5 TPED -58/2 7.5 TPED -12/2.75 TPED -16/2 1.1 TPED -18/2.75 TPED -19/2 1.5 TPED -2/2 2.2 TPED -29/2 3. TPED -36/2. TPED -3/2 5.5 TPED -57/2 11 TPED -71/2 15 TPED -83/ TPED -9/2 22 TPED 65-12/2 1.1 TPED 65-18/2 1.5 TPED 65-19/2 2.2 TPED 65-23/2 3. TPED 65-26/2. TPED 65-3/2 5.5 TPED 65-1/2 7.5 TPED 65-6/2 11 TPED 65-5/2 15 TPED 65-66/ TPED 65-72/2 22 TPED 8-12/2 1.5 TPED 8-21/2. TPED 8-2/2 5.5 TPED 8-33/2 11 TPED 8-/2 15 TPED 8-52/ TPED 8-57/2 22 TPED 1-12/2 2.2 TPED 65-6/.55 TPED 65-9/.75 TPED 8-6/.75 TPED 1-3/.55 TPED 1-6/ 1.1 5

46 Installation TP, TPD, TPE, TPED Electrical installation Electrical connection Carry out electrical connection and protection in accordance with local regulations. The pump must be connected to an external mains switch with a minimum contact gap of 3 mm in all poles. Electronically speed-controlled pumps must always be correctly earthed. Note: The kw motors must be connected to especially reliable/sturdy earth connections to avoid earth leakage currents above 3.5 ma. Single-phase motors incorporate thermal protection and require no additional motor protection. Three-phase mains-operated motors must be connected to a motor-protective circuit breaker. Motors as from 3 kw have thermistors (PTC). The thermistors are designed according to DIN 82. When the pump is switched on via the mains, the pump will start after approx. 5 seconds. Note: Carry out the mains connection of the pump as shown in the diagram inside the terminal box cover. Do not start the pump until it has been filled with liquid and vented. Protection Protection against fault currents If the pump is connected to an electric installation where an earth leakage circuit breaker (ELCB) is used as additional protection, the earth leakage circuit breaker must be marked with the following symbols. Single-phase: Protection against voltage peaks If you use speed controllers or frequency converters of other makes than Grundfos, you may have the following problems: increased motor noise detrimental voltage peaks additional motor losses. Pumps with voltage peaks exceeding 6 V (maximum value) must therefore be protected. The voltage increase rate du/dt must not exceed Vμs. Noise and detrimental voltage peaks can be prevented by fitting an LC filter between the speed controller and the motor. Communication cables for TPE, TPED Use screened cables (min..5 mm 2 ) for external on/off switch, digital input, sensor and setpoint signals. The screens of the cables should be connected to frame at both ends. The screen of the cable must have good frame connection which must be as close as possible to the terminals. Screen Fig. 36 External start/stop cable connection of TPE, TPED Use a screened 2-core cable for the bus connection. Connect the screen to terminal Y at both ends. TM The earth leakage circuit breaker must trip out when earth fault currents with DC content (pulsating DC) occur. Three-phase: The earth leakage circuit breaker must trip out when earth fault currents with DC content (pulsating DC) and smooth DC earth fault currents occur. Screen Fig. 37 Bus connection of TPE, TPED Y TM

47 Installation TP, TPD, TPE, TPED Other connections, TPE, TPED See the wiring diagrams for instructions on how to connect external potential-free contacts for start/stop and digital function, external setpoint signal and fault signal. Connect the wires to the following terminal groups: Wiring diagram, three-phase, kw NC C NO Group 2 L1 L2 L3 Group 3 Group 1: Inputs (external start/stop, digital function, setpoint and sensor signals, terminals 1-9 and bus connection, A, Y, B). All inputs are separated from the mains conducting parts by reinforced insulation. Group 2: Output (signal relay). The output, terminals C, NO and NC, are galvanically separated from other circuits. Therefore, the supply voltage or protective extra-low voltage can be connected to the output as desired. -1 V /-2 ma -2 ma 1/ B Y A Group 1 STOP Group 3: Mains supply. Note: As a precaution, separate the wires from each other by reinforced insulation in their entire lengths. If no external on/off switch is connected, maintain the connection across terminals 2 and 3. Wiring diagram, single-phase RUN /-2 ma -1 V 1K Fig. 39 Wiring diagram, three-phase TPE pumps Wiring diagram, three-phase, kw TM Signal relay NC C NO Group 2 N PE L Mains connection Group 3 Group 2 Group 3-1 V /-2 ma -2 ma / B Y A STOP RUN /-2 ma -1 V 1K Group 1 TM Group 1 Fig. Wiring diagram, three-phase TPE pumps TM Fig. 38 Wiring diagram, single-phase TPE pumps 7

48 Flanges for TP pumps TP, TPD, TPE, TPED Flange dimensions PN 6 and PN 1 flanges D 1 D 2 D 3 S TM EN PN 6 (.6 MPa) EN PN 1 (1. MPa) Nominal diameter (DN) Nominal diameter (DN) D D D S x1 x1 x1 x1 x19 x19 x19 x19 x19 x19 8x19 8x19 8x19 8x23 8x23 12x23 PN 16 and PN 25 flanges D 1 D 2 D 3 S TM EN PN 16 (1.6 MPa) EN PN 25 (2.5 MPa) Nominal diameter (DN) Nominal diameter (DN) D D D S x19 x19 x19 x19 8x19 8x19 8x19 8x23 12x23 8x23 8x28 8x28 12x28 12x31 16x31 16x3 PN flanges D 1 D 2 D 3 S TM EN/DIN 2635 PN (. MPa) Nominal diameter (DN) D 1 D D S 16x2 2x2 8

49 Curve charts TP, TPD, TPE, TPED How to read the curve charts H /2-6/2-38/2-32/2-2/2-2/2 TP, TPE 32 Hz Q [m³/h] 6-58/2 5-6/2 Pump type and frequency QH curve for the individual single-head pump. The bold curve indicates the recommended performance range. The power curve indicates pump input power [P 2 ] /2-2/2-32/2-38/ Q [m³/h] NPSH Eta [%] Q [m³/h] -2/2-2/2-32/2-38/2-6/2-58/2 The NPSH (3 %) curve shows the required net positive suction head (NPSH) to ensure that the pump head is not reduced by more than 3 %. The available system pressure at the pump inlet must be according to the NPSH (3 %) curve + a safety margin of at least.5 m. The eta curve shows the pump efficiency Q [m³/h] 2 6 Q [l/s] 2 6 v [m/s] TM

50 Curve charts TP, TPD, TPE, TPED Curve conditions The guidelines below apply to the curves shown on the following pages: Tolerances to ISO 996, Annex A. The curves apply to the performance of single-head three-phase pumps. For other pump versions, please see the exact curves in WinCAPS or WebCAPS. For other pump versions, the performance may differ for the following reasons: - The valve in twin-head pumps may cause losses. - Single-phase motors run at lower speed. Note: Grundfos does not recommend continuous parallel operation of twin-head pumps due to the increased flow in the pump. A too high flow results in noisy operation, increased wear of the impeller due to cavitation, etc. QH curves of the individual single-head pumps are shown with expected speed of a three-phase mainsoperated motor. For further information, see the tables of technical data on the following pages. The performance of the single-phase motor is slightly reduced. Please refer to WinCAPS or WebCAPS for the exact single-phase curves. Curves of TPE Series 1 pumps and TPE Series 2 pumps are shown as nominal curves (1 % curves) only. Please refer to WinCAPS for the exact curves. Measurements have been made with airless water at a temperature of +2 C. The curves apply to a kinematic viscosity of υ =1mm 2 /s (1 cst). Due to the risk overheating, the pump must not run constantly below the minimum flow rate indicated by the bold curves. If the pumped liquid density and/or viscosity are higher than those of water, it may be necessary to use a motor with a higher performance.

51 51

52 Technical data/ performance curves G 1 1/2 2-pole, PN 6, 1, 16 TP, TPD, TPE, TPED, 2-pole, PN 6, 1, 16 TP, TPE 25-XX /2 R H /2 R -/2 R TP, TPE 25 Hz Q [m³/h] -9/2 R.8 -/2 R Q [m³/h] NPSH 3 -/2 R, -9/2 R 2 1 Eta [%] Q [m³/h] -/2 R -9/2 R Q [m³/h] Q [l/s] v [m/s] TM

53 Performance curves G 1 1/2 2-pole, PN 6, 1, 16 TM H1 G H2 H3 H3 B1 B2 L1 AE AF Technical data TP 25 -/2 R -9/2 R TPD - - TPE TPED - - Series phase TP IEC size 3-phase TP phase TPE phase TPE /3-phase TP.12/.12.25/.25 1-/3-phase TPE.37/-.37/- PN 1 1 T min ; T max [ C] [-25;11] [-25;11] G G 1 ½ G 1 ½ 1-/3-phase TP [mm] 118/ /118 1-/3-phase TPE [mm] 11/- 11/- 1-/3-phase TP [mm] 11/11 111/11 1-/3-phase TPE [mm] 1/- 1/- AE 1-/3-phase TPE [mm] 15/- 15/- AF 1-/3-phase TPE [mm] 15/- 15/- B1 [mm] 5 5 B2 [mm] /3-phase TP [mm] 11/- 111/- 1-/3-phase TPE [mm] 1/- 1/- L1 [mm] H1 [mm] H2 [mm] H3 1-/3-phase TP [mm] 323/ /323 1-/3-phase TPE [mm] 33/- 33/- 53

54 Technical data G 2 2-pole, PN 6, 1, 16 TP, TPE 32-XX/2 H /2 R -/2 R TP, TPE 32 Hz Q [m³/h] /2 R -9/2 R Q [m³/h] NPSH 3. -9/2 R Eta [%] /2 R Q [m³/h] -/2 R -9/2 R Q [m³/h] Q [l/s] v [m/s] TM

55 Performance curves G 2 2-pole, PN 6, 1, 16 TM2 838 H1 G H2 H3 H3 B1 B2 L1 AE AF Technical data TP 32 -/2 R -9/2 R TPD - - TPE TPED - - Series phase TP IEC size 3-phase TP phase TPE phase TPE /3-phase TP.12/.12.25/.25 1-/3-phase TPE.37/-.37/- PN 1 1 T min ; T max [ C] [-25;11] [-25;11] G G 2 G 2 1-/3-phase TP [mm] 118/ /118 1-/3-phase TPE [mm] 11/- 11/- 1-/3-phase TP [mm] 11/11 111/11 1-/3-phase TPE [mm] 1/- 1/- AE 1-/3-phase TPE [mm] 15/- 15/- AF 1-/3-phase TPE [mm] 15/- 15/- B1 [mm] B2 [mm] /3-phase TP [mm] 11/- 111/- 1-/3-phase TPE [mm] 1/- 1/- L1 [mm] H1 [mm] H2 [mm] H3 1-/3-phase TP [mm] 338/ /338 1-/3-phase TPE [mm] 33/- 33/- 55

56 Technical data DN 32 2-pole, PN 6, 1, 16 TPED 32-XX/2 H 2-23/2 TP, TPE Hz / /2-12/ / Q [m³/h] -23/ /2. -1/2-12/ / Q [m³/h] NPSH /2, -18/2, -23/2-12/2-6/2 H /2-6/2-38/2-32/2-2/2-2/2 TP, TPE 32 Hz Q [m³/h] 6-58/2 5-2/2-2/2-32/2-6/2-38/ Q [m³/h] NPSH Eta [%] Q [m³/h] -18/2-6/2-12/2-23/2-1/ Q [m³/h] Eta [%] Q [m³/h] -2/2-2/2-32/2-38/2-6/2-58/ Q [m³/h] Q [l/s] v [m/s] TM Q [l/s] 2 6 v [m/s] TM Note: All curves apply to single-head pumps. For further information, see page. 56

57 Performance curves DN 32 2-pole, PN 6, 1, 16 P B3 P AF H3 AE D1 B1 B2 Rp 1/ M L1 C5 H1 H2 H C1 B1 D1 B2 AE AF AE AF M M L1 C6 C5 H H1 H2 C1 TM TM Technical data TP 32-6/2-12/2-1/2-18/2-23/2-2/2-2/2-32/2-38/2-6/2-58/2 TPD TPE TPED Series IEC size 1-phase TP phase TP phase TPE phase TPE /3-phase TP.25/.25.37/.37.37/.37.55/.55.75/.75 -/1.1 -/1.5 -/2.2 -/3 -/ -/5.5 1-/3-phase TPE.37/-.37/-.37/-.55/-.75/ /1.1 -/1.5 -/2.2 -/3 -/ -/5.5 PN PN 6/1 PN 6/1 PN 6/1 PN 6/1 PN 6/1 PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 T min ; T max [ C] [-25;1] [-25;1] [-25;1] [-25;1] [-25;1] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] D1 [mm] /3-phase TP [mm] 12/12 11/12 11/11 11/11 11/11 -/11 -/178 -/178 -/198 -/22 -/22 1-/3-phase TPE [mm] 11/- 11/- 11/- 11/- 11/178 11/178 -/178 -/178 -/198 -/22 -/22 1-/3-phase TP [mm] 11/11 133/ /19 133/19 133/19 -/19 -/11 -/11 -/12 -/13 -/13 1-/3-phase TPE [mm] 1/- 1/- 1/- 1/- 1/167 1/167 -/167 -/167 -/177 -/188 -/188 AE 1-/3-phase TPE [mm] 15/- 15/- 15/- 15/- 15/132 15/15 -/132 -/132 -/132 -/15 -/15 AF 1-/3-phase TPE [mm] 15/- 15/- 15/- 15/- 15/132 15/15 -/132 -/132 -/132 -/15 -/15 P [mm] 9/ B1 [mm] 75/176 75/18 12/222 12/222 12/ /26 125/26 125/26 125/26 1/321 1/321 B2 [mm] 75/176 75/18 12/222 12/222 12/ / / / /257 1/321 1/321 B3 [mm] phase TPE [mm] 1/26 1/26 1/225 1/225 1/225 1/ TP [mm] 75/ /18 133/ / / /26 125/26 125/26 125/263 1/321 1/328 3-phase TPE [mm] /32 1/ / / /3 188/3 188/3 C1 [mm] 8/2 8/2 8/2 8/2 8/2 1/356 1/356 1/356 1/356 1/35 1/35 C5 [mm] 11/52 11/52 1/82 1/82 1/82 17/5 17/5 17/5 17/5 22/6 22/6 C6 [mm] L1 [mm] H1 [mm] H2 [mm] 1/ /3-phase TP [mm] 387/ / /395 7/395 7/7 -/5 -/535 -/575 -/618 -/656 -/71 H3 1-/3-phase TPE [mm] 7/- 385/- 395/- 395/- 7/97 85/535 -/535 -/575 -/618 -/656 -/71 H [mm] M M12 M12 M12 M12 M12 M16 M16 M16 M16 M16 M16 TP(E), TP(E)D pumps are primarily fitted with IE3 motors. See section Motors on pages 36 to. The dimension before the slash applies to the single-head pump and the dimension after the slash applies to the twin-head pump. 57

58 Technical data DN 2-pole, PN 6, 1, 16 TP, TPE -XX/2 H /2 -/2 TP, TPE Hz Q [m³/h].2 -/2-9/2 H /2-23/2-19/2-18/2-12/2-6/2 TP, TPE Hz Q [m³/h] -19/2-27/2-23/2-6/2-18/2-12/ Q [m³/h] NPSH 3. -9/ Q [m³/h] NPSH 1-19/2, -23/2, -27/ Eta [%] / Q [m³/h] -/2-9/ Q [m³/h] Eta [%] Q [m³/h] -6/2-12/2-18/2-6/2-23/2-18/2-12/2-19/2-27/ Q [m³/h] Q [l/s] v [m/s] TM Q [l/s] v [m/s] TM Note: All curves apply to single-head pumps. For further information, see page. 58

59 Performance curves DN 2-pole, PN 6, 1, 16 P B3 P AF AE H3 D1 B1 B2 Rp 1/ M L1 C5 H1 H2 H C1 B1 D1 B2 AE AF AE AF M M L1 C6 C5 H H1 H2 C1 TM TM Technical data TP -/2-6/2-9/2-12/2-18/2-19/2-23/2-27/2 TPD TPE - TPED Series IEC size 1-phase TP phase TP phase TPE phase TPE /3-phase TP.12/.12.25/.25.25/.25.37/.37.55/.55.75/ / /1.5 1-/3-phase TPE.37/-.37/-.37/-.37/-.55/-.75/ /1.1 -/1.5 PN PN 6/1 PN 6/1 PN 6/1 PN 6/1 PN 6/1 PN 16 PN 16 PN 16 T min ; T max [ C] [-25;11] [-25;1] [-25;11] [-25;1] [-25;1] [-25;1] [-25;1] [-25;1] D1 [mm] 1-/3-phase TP [mm] 118/118 11/11 139/118 11/11 11/11 11/11 178/11 178/178 1-/3-phase TPE [mm] 11/- 11/- 11/- 11/- 11/- 11/178 11/178 -/178 1-/3-phase TP [mm] 11/11 133/19 111/11 133/19 133/19 133/19 139/19 139/11 1-/3-phase TPE [mm] 1/- 1/- 11/- 1/- 11/- 1/167 1/167 -/167 AE 1-/3-phase TPE [mm] 15/- 15/- 15/- 15/- 15/- 15/132 15/132 -/132 AF 1-/3-phase TPE [mm] 15/- 15/- 15/- 15/- 15/- 15/132 15/132 -/132 P [mm] B1 [mm] 75/- 75/18 75/- 75/18 1/- 12/222 12/222 12/222 B2 [mm] 75/- 75/18 75/- 75/18 1/- 12/222 12/222 12/222 B3 [mm] phase TPE [mm] 1/275 1/26 11/275 1/26 11/225 1/225 1/225 - TP [mm] 11/- 133/18 111/- 133/18 133/- 133/ / /222 3-phase TPE [mm] /32 167/32 167/32 C1 [mm] -/- 8/2 -/- 8/2 8/- 12/2 12/2 12/2 C5 [mm] -/- 125/5 -/- 125/5 125/- 16/95 16/95 16/95 C6 [mm] L1 [mm] H1 [mm] H2 [mm] /3-phase TP [mm] 353/ / / /387 2/39 39/39 99/51 539/ H3 1-/3-phase TPE [mm] 36/- 395/- 36/- 388/- 39/- 32/9 39/9 -/ H [mm] M - M12 - M12 M12 M12 M12 M12 TP(E), TP(E)D pumps are primarily fitted with IE3 motors. See section Motors on pages 36 to. The dimension before the slash applies to the single-head pump, and the dimension after the slash applies to the twin-head pump. 59

60 Technical data DN 2-pole, PN 6, 1, 16 TP, TPD, TPE, TPED -XX/2 H /2-7/2-36/2-3/2-2/2 TP, TPE Hz Q [m³/h] 8-7/2-2/2-3/2-58/2-36/ Q [m³/h] NPSH 1 8-3/2, 36/2, 7/2, 58/2 6-2/2 2 Eta [%] Q [m³/h] -3/2-36/2-2/2-7/2-58/ Q [m³/h] Q [l/s] 2 6 v [m/s] TM2 2 Note: All curves apply to single-head pumps. For further information, see page. 6

61 Performance curves DN 2-pole, PN 6, 1, 16 P B3 P AF H3 AE D1 B1 B2 Rp 1/ M L1 C5 H1 H2 H C1 B1 D1 B2 AE AF AE AF M M L1 C6 C5 H H1 H2 C1 TM TM Technical data TP -2/2-3/2-36/2-7/2-58/2 TPD TPE TPED Series IEC size 1-phase TP phase TP phase TPE phase TPE /3-phase TP -/2.2 -/3 -/ -/5.5 -/7.5 1-/3-phase TPE -/2.2 -/3 -/ -/5.5 -/7.5 PN PN 16 PN 16 PN 16 PN 16 PN 16 T min ; T max [ C] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] D1 [mm] 1-/3-phase TP [mm] -/178 -/198 -/22 -/22 -/26 1-/3-phase TPE [mm] -/178 -/198 -/22 -/22 -/26 1-/3-phase TP [mm] -/11 -/12 -/13 -/13 -/159 1-/3-phase TPE [mm] -/167 -/177 -/188 -/188 -/213 AE 1-/3-phase TPE [mm] -/132 -/132 -/15 -/15 -/15 AF 1-/3-phase TPE [mm] -/132 -/132 -/15 -/15 -/15 P [mm] B1 [mm] 13/273 13/273 13/273 19/325 19/325 B2 [mm] 117/ / /267 1/321 1/321 B3 [mm] phase TPE [mm] TP [mm] 13/273 13/273 13/273 1/ /328 3-phase TPE [mm] 167/35 177/ /37 188/3 213/1 C1 [mm] 1/ 1/ 1/ 1/35 1/35 C5 [mm] 17/5 17/5 17/5 22/18 22/18 C6 [mm] L1 [mm] H1 [mm] H2 [mm] /3-phase TP [mm] -/587 -/629 -/666 -/726 -/71 H3 1-/3-phase TPE [mm] -/587 -/629 -/666 -/726 -/71 H [mm] M M16 M16 M16 M16 M16 TP(E), TP(E)D pumps are primarily fitted with IE3 motors. See section Motors on pages 36 to. The dimension before the slash applies to the single-head pump, and the dimension after the slash applies to the twin-head pump. 61

62 Technical data DN 2-pole, PN 6, 1, 16 TP, TPD, TPE, TPED -XX/2 H /2-2/2-19/2-16/2-18/2-12/2-6/2 TP, TPE Hz Q [m³/h] -2/2-29/ /2-16/2-18/2-12/2-6/ Q [m³/h] NPSH /2 6 2 Eta [%] /2-12/2-16/2, -19/2, 2/2, -29/ Q [m³/h] -18/2-16/2-12/2-6/2-2/2-19/2-29/ Q [m³/h] Q [l/s] v [m/s] TM Note: All curves apply to single-head pumps. For further information, see page. 62

63 Performance curves DN 2-pole, PN 6, 1, 16 P B3 P AF AE H3 D1 B1 B2 Rp 1/ M L1 C5 H1 H2 H C1 B1 D1 B2 AE AF AE AF M M L1 C6 C5 H H1 H2 C1 TM TM Technical data TP -6/2-12/2-18/2-16/2-19/2-2/2-29/2 TPD TPE TPED Series IEC size 1-phase TP phase TP phase TPE phase TPE /3-phase TP.37/.37.75/.75.75/.75 -/1.1 -/1.5 -/2.2 -/3 1-/3-phase TPE.37/-.75/.75.75/ /1.1 -/1.5 -/2.2 -/3 PN PN 6/1 PN 6/1 PN 6/1 PN 16 PN 16 PN 16 PN 16 T min ; T max [ C] [-25;1] [-25;1] [-25;1] [-25;12] [-25;12] [-25;12] [-25;12] D1 [mm] 1-/3-phase TP [mm] 11/11 11/11 11/11 -/11 -/178 -/178 -/198 1-/3-phase TPE [mm] 11/- 11/178 11/ /11 -/178 -/178 -/198 1-/3-phase TP [mm] 133/ / /19 -/19 -/11 -/11 -/12 1-/3-phase TPE [mm] 1/- 1/167 1/167 1/167 -/167 -/167 -/177 AE 1-/3-phase TPE [mm] 15/- 15/132 15/132 15/132 -/132 -/132 -/132 AF 1-/3-phase TPE [mm] 15/- 15/132 15/132 15/132 -/132 -/132 -/132 P [mm] 15/15 12/ B1 [mm] 9/177 1/221 1/ / / / /252 B2 [mm] 75/188 1/221 1/ / / / /252 B3 [mm] phase TPE [mm] 1/26 1/225 1/225 1/ TP [mm] 9/188 1/ / / / / /26 3-phase TPE [mm] - 167/32 167/32 1/ / / /335 C1 [mm] 12/2 12/2 12/2 1/3 1/3 1/3 1/3 C5 [mm] 1/6 1/6 1/6 17/6 17/6 17/6 17/6 C6 [mm] L1 [mm] H1 [mm] 75 75/ H2 [mm] / /3-phase TP [mm] 3/3 1/1 1/1 -/518 -/58 -/588 -/63 H3 1-/3-phase TPE [mm] 3/- 2/91 1/91 98/58 -/58 -/588 -/63 H [mm] M M12 M12 M12 M16 M16 M16 M16 TP(E), TP(E)D pumps are primarily fitted with IE3 motors. See section Motors on pages 36 to. The dimension before the slash applies to the single-head pump, and the dimension after the slash applies to the twin-head pump. 63

64 Technical data DN 2-pole, PN 6, 1, 16 TP, TPD, TPE, TPED -XX/2 H /2-83/2-71/2 TP, TPE Hz 6-57/2 3 -/2-3/2-36/ Q [m³/h] /2 -/2-3/2-57/2-71/2-83/2-9/ Q [m³/h] NPSH Eta [%] Q [m³/h] -36/2-3/2 -/2-57/2-9/2-71/2-83/ Q [m³/h] Q [l/s] v [m/s] TM2 22 Note: All curves apply to single-head pumps. For further information, see page. 6

65 Performance curves DN 2-pole, PN 6, 1, 16 P B3 P AF H3 AE D1 B1 B2 Rp 1/ M L1 C5 H1 H2 H C1 B1 D1 B2 AE AF AE AF M M L1 C6 C5 H H1 H2 C1 TM TM Technical data TP -36/2-3/2 -/2-57/2-71/2-83/2-9/2 TPD TPE TPED Series IEC size 1-phase TP phase TP phase TPE phase TPE /3-phase TP -/ -/5.5 -/7.5 -/11 -/15 -/18.5 -/22 1-/3-phase TPE -/ -/5.5 -/7.5 -/11 -/15 -/18.5 -/22 PN PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 T min ; T max [ C] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] D1 [mm] 1-/3-phase TP [mm] -/22 -/22 -/26 -/31 -/31 -/31 -/31 1-/3-phase TPE [mm] -/22 -/22 -/26 -/31 -/31 -/31 -/31 1-/3-phase TP [mm] -/13 -/13 -/159 -/2 -/2 -/2 -/2 1-/3-phase TPE [mm] -/188 -/188 -/213 -/38 -/38 -/38 -/38 AE 1-/3-phase TPE [mm] -/15 -/15 -/15 -/21 -/21 -/21 -/21 AF 1-/3-phase TPE [mm] -/15 -/15 -/15 -/21 -/21 -/21 -/21 P [mm] B1 [mm] 133/29 133/29 18/386 18/386 18/386 18/386 18/386 B2 [mm] 119/28 119/28 16/379 16/379 16/379 16/379 16/379 B3 [mm] phase TPE [mm] TP [mm] 13/29 1/31 18/386 2/386 2/386 2/386 2/386 3-phase TPE [mm] 188/ / /386 38/58 38/58 38/58 38/58 C1 [mm] 1/ 1/ 1/ 1/ 1/ 1/ 1/ C5 [mm] 17/52 17/52 22/123 22/123 22/123 22/123 22/123 C6 [mm] L1 [mm] 3 3 H1 [mm] H2 [mm] /3-phase TP [mm] -/676 -/73 -/728 -/8 -/8 -/89 -/89 H3 1-/3-phase TPE [mm] -/676 -/73 -/728 -/8 -/8 -/89 -/92 H [mm] M M16 M16 M16 M16 M16 M16 M16 TP(E), TP(E)D pumps are primarily fitted with IE3 motors. See section Motors on pages 36 to. The dimension before the slash applies to the single-head pump, and the dimension after the slash applies to the twin-head pump. 65

66 Technical data DN 65 2-pole, PN 6, 1, 16 TP, TPD, TPE, TPED 65-XX/2 H /2-23/2-19/2-18/2-12/2-6/2 TP, TPE 65 Hz Q [m³/h]. -26/2-6/2-19/2-12/2-23/2-18/ Q [m³/h] NPSH 5-12/ /2-18/2-19/2, -23/2, -26/2 Eta [%] Q [m³/h] -6/2-12/2-18/2-23/2-19/2-26/ Q [m³/h] Q [l/s] v [m/s] TM Note: All curves apply to single-head pumps. For further information, see page. 66

67 Performance curves DN 65 2-pole, PN 6, 1, 16 P B3 P AF AE H3 D1 B1 B2 Rp 1/ M L1 C5 H1 H2 H C1 B1 D1 B2 AE AF AE AF M M L1 C6 C5 H H1 H2 C1 TM TM Technical data TP 65-6/2-12/2-18/2-19/2-23/2-26/2 TPD TPE TPED Series IEC size 1-phase TP phase TP phase TPE phase TPE /3-phase TP.55/ / /1.5 -/2.2 -/3 -/ 1-/3-phase TPE.55/- 1.1/1.1 -/1.5 -/2.2 -/3 -/ PN PN 6/1 PN 6/1 PN 6/1 PN 16 PN 16 PN 16 T min ; T max [ C] [-25;1] [-25;1] [-25;1] [-25;12] [-25;12] [-25;12] D1 [mm] /3-phase TP [mm] 11/11 178/11 178/178 -/178 -/198 -/22 1-/3-phase TPE [mm] 11/- 11/178 -/178 -/178 -/198 -/22 1-/3-phase TP [mm] 133/19 139/19 139/11 -/11 -/12 -/13 1-/3-phase TPE [mm] 1/- 1/167 -/167 -/167 -/177 -/188 AE 1-/3-phase TPE [mm] 15/- 15/132 -/132 -/132 -/132 -/15 AF 1-/3-phase TPE [mm] 15/- 15/132 -/132 -/132 -/132 -/15 P [mm] B1 [mm] 93/195 1/225 1/225 12/298 12/298 12/298 B2 [mm] 93/21 1/225 1/225 12/29 12/29 12/29 B3 [mm] phase TPE [mm] 1/225 1/ TP [mm] 133/ / /225 12/298 12/298 12/298 3-phase TPE [mm] - 167/32 167/32 167/36 177/ /385 C1 [mm] 12/2 12/2 12/2 1/ 1/ 1/ C5 [mm] 17/63 17/63 17/63 18/65 18/65 18/65 C6 [mm] L1 [mm] H1 [mm] H2 [mm] /3-phase TP [mm] 68/18 517/ /7 -/598 -/61 -/678 H3 1-/3-phase TPE [mm] 18/- 62/512 -/517 -/598 -/61 -/678 H [mm] M M12 M12 M12 M16 M16 M16 TP(E), TP(E)D pumps are primarily fitted with IE3 motors. See section Motors on pages 36 to. The dimension before the slash applies to the single-head pump, and the dimension after the slash applies to the twin-head pump. 67

68 Technical data DN 65 2-pole, PN 6, 1, 16 TP, TPD, TPE, TPED 65-XX/2 H /2-72/2-66/2-5/2-6/2-1/2-3/2 TP, TPE 65 Hz Q [m³/h] 32-93/ /2-66/2 16-5/2 12-6/2 8-1/2-3/ Q [m³/h] NPSH Eta [%] Q [m³/h] -1/2-93/2-3/2-72/2-5/2-66/2-6/ Q [m³/h] Q [l/s] 2 6 v [m/s] TM2 2 Note: All curves apply to single-head pumps. For further information, see page. 68

69 Performance curves DN 65 2-pole, PN 6, 1, 16 P B3 P AF H3 AE D1 B1 B2 Rp 1/ M L1 C5 H1 H2 H C1 B1 D1 B2 AE AF AE AF M M L1 C6 C5 H H1 H2 C1 TM TM Technical data TP 65-3/2-1/2-6/2-5/2-66/2-72/2-93/2 TPD TPE - TPED - Series IEC size 1-phase TP phase TP phase TPE phase TPE /3-phase TP -/5.5 -/7.5 -/11 -/15 -/18.5 -/22 -/3 1-/3-phase TPE -/5.5 -/7.5 -/11 -/15 -/18.5 -/22 -/- PN PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 T min ; T max [ C] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] D1 [mm] /3-phase TP [mm] -/22 -/26 -/31 -/31 -/31 -/31 -/7 1-/3-phase TPE [mm] -/22 -/26 -/31 -/31 -/31 -/31 -/- 1-/3-phase TP [mm] -/13 -/159 -/2 -/2 -/2 -/2 -/315 1-/3-phase TPE [mm] -/188 -/213 -/38 -/38 -/38 -/38 -/- AE 1-/3-phase TPE [mm] -/15 -/15 -/21 -/21 -/21 -/21 - AF 1-/3-phase TPE [mm] -/15 -/15 -/21 -/21 -/21 -/21 - P [mm] B1 [mm] 12/298 12/ /39 178/39 178/39 178/39 178/39 B2 [mm] 12/29 12/29 16/383 16/383 16/383 16/383 16/383 B3 [mm] phase TPE [mm] TP [mm] 1/31 159/31 2/395 2/395 2/395 2/395 3/21 3-phase TPE [mm] 188/ /396 38/558 38/558 38/558 38/558 - C1 [mm] 1/ 1/ 1/52 1/52 1/52 1/52 1/52 C5 [mm] 18/65 18/65 238/ / / / /111 C6 [mm] L1 [mm] H1 [mm] H2 [mm] /3-phase TP [mm] -/735 -/723 -/859 -/859 -/93 -/93 -/999 H3 1-/3-phase TPE [mm] -/735 -/723 -/859 -/859 -/93 -/929 -/- H [mm] M M16 M16 M16 M16 M16 M16 M16 TP(E), TP(E)D pumps are primarily fitted with IE3 motors. See section Motors on pages 36 to. The dimension before the slash applies to the single-head pump, and the dimension after the slash applies to the twin-head pump. 69

70 Technical data DN 8 2-pole, PN 6, 1, 16 TP, TPD, TPE, TPED 8-XX/2 H /2-21/2-18/2-1/2-12/2 TP, TPE 8 Hz Q [m³/h] -18/2-1/2-12/2-21/2-2/ Q [m³/h] NPSH 1 H 75 7 TP, TPE 8 Hz -7/ / /2 5 -/ /2 3-2/ Q [m³/h] /2 2-57/ /2 12 -/2 8-33/2-2/ Q [m³/h] NPSH 1-52/2, 57/2, 7/2 8-12/2 8-2/2 6-1/2-18/2, 21/2, 2/2 6-33/2, -/2 2 2 Eta [%] Q [m³/h] -21/2-12/2-2/2-18/2-1/ Q [m³/h] Eta [%] Q [m³/h] -7/2-57/2-2/2 -/2-33/2-52/ Q [m³/h] Q [l/s] v [m/s] TM Q [l/s] v [m/s] TM Note: All curves apply to single-head pumps. For further information, see page. 7

71 Performance curves DN 8 2-pole, PN 6, 1, 16 P B3 P AF H3 AE H3 D1 B1 B2 Rp 1/ M L1 C5 H H1 H2 C1 B1 D1 B2 AE AF AE AF M M L1 C6 C5 H H1 H2 C1 TM TM Technical data TP 8-12/2-1/2-18/2-21/2-2/2-2/2-33/2 -/2-52/2-57/2-7/2 TPD TPE - TPED - Series IEC size 1-phase TP phase TP phase TPE phase TPE /3-phase TP 1.5/1.5 -/2.2 -/3 -/ -/5.5 -/7.5 -/11 -/15 -/18.5 -/22 -/3 1-/3-phase TPE -/1.5 -/2.2 -/3 -/ -/5.5 -/7.5 -/11 -/15 -/18.5 -/22 -/- PN PN 6/PN1 PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 T min ; T max [ C] [-25;1] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] D1 [mm] /3-phase TP [mm] 178/178 -/178 -/198 -/22 -/22 -/26 -/31 -/31 -/31 -/31 -/2 1-/3-phase TPE [mm] -/178 -/178 -/198 -/22 -/22 -/26 -/31 -/31 -/31 -/31 -/- 1-/3-phase TP [mm] 139/139 -/11 -/12 -/13 -/13 -/159 -/2 -/2 -/2 -/2 -/315 1-/3-phase TPE [mm] -/167 -/167 -/177 -/188 -/188 -/213 -/38 -/38 -/38 -/38 -/- AE 1-/3-phase TPE [mm] -/ AF 1-/3-phase TPE [mm] -/ P [mm] 135/ B1 [mm] 12/13 125/ / / / / / / /16 187/16 187/16 B2 [mm] 1/ /29 119/29 119/29 119/29 1/35 1/35 1/35 162/5 162/5 162/5 B3 [mm] phase TPE [mm] TP [mm] 12/ / /296 13/296 1/32 176/366 2/375 2/375 2/16 2/16 3/36 3-phase TPE [mm] 167/32 167/ / / / /366 38/538 38/538 38/573 38/573 - C1 [mm] 16/2 1/2 1/2 1/2 1/2 1/8 1/8 1/8 1/5 1/5 1/5 C5 [mm] 18/53 18/78 18/78 18/78 18/78 22/93 22/93 22/93 2/133 2/133 2/133 C6 [mm] L1 [mm] H1 [mm] H2 [mm] /3-phase TP [mm] 581/581 -/62 -/6 -/681 -/739 -/737 -/859 -/859 -/93 -/93 -/999 H3 1-/3-phase TPE [mm] -/51 -/62 -/6 -/681 -/739 -/737 -/859 -/859 -/93 -/929 -/- H [mm] M M16 M16 M16 M16 M16 M16 M16 M16 M16 M16 M16 TP(E), TP(E)D pumps are primarily fitted with IE3 motors. See section Motors on pages 36 to. The dimension before the slash applies to the single-head pump, and the dimension after the slash applies to the twin-head pump. 71

72 Technical data DN 1 2-pole, PN 6, 1, 16 TP, TPD, TPE, TPED 1-XX/2 H /2-2/2-16/2-12/2 TP, TPE 1 Hz Q [m³/h] 8-2/2 7 H /2-39/2-36/2-31/2-2/2 TP, TPE 1 Hz Q [m³/h] -8/ /2-16/2-12/ /2-39/2-36/2-31/ Q [m³/h] NPSH /2-16/2-2/2, -2/2 NPSH Q [m³/h] 1-8/ /2, -31/2-36/2, -39/2 Eta [%] Q [m³/h] -2/2-16/2-2/2-12/ Q [m³/h] Eta [%] Q [m³/h] -8/2-2/2-39/2-36/2-31/ Q [m³/h] Q [l/s] v [m/s] TM Q [l/s] v [m/s] TM Note: All curves apply to single-head pumps. For further information, see page. 72

73 Performance curves DN 1 2-pole, PN 6, 1, 16 P B3 P H3 AF AE H3 D1 B1 B2 Rp 1/ M L1 C5 H H1 H2 C1 B1 D1 B2 AE AF AE AF M M L1 C6 C5 H H1 H2 C1 TM TM Technical data TP 1-12/2-16/2-2/2-2/2-2/2-31/2-36/2-39/2-8/2 TPD TPE - TPED - Series IEC size 1-phase TP phase TP phase TPE phase TPE /3-phase TP -/2.2 -/ -/5.5 -/7.5 -/11 -/15 -/18.5 -/22 -/3 1-/3-phase TPE -/2.2 -/ -/5.5 -/7.5 -/11 -/15 -/18.5 -/22 -/- PN PN 6/PN 1 PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 T min ; T max [ C] [-25;1] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] D1 [mm] /3-phase TP [mm] -/178 -/22 -/22 -/26 -/31 -/31 -/31 -/31 -/7 1-/3-phase TPE [mm] -/178 -/22 -/22 -/26 -/31 -/31 -/31 -/31 -/- 1-/3-phase TP [mm] -/11 -/13 -/13 -/159 -/2 -/2 -/2 -/2 -/315 1-/3-phase TPE [mm] -/167 -/188 -/188 -/213 -/38 -/38 -/38 -/38 -/- AE 1-/3-phase TPE [mm] -/ AF 1-/3-phase TPE [mm] -/ P [mm] B1 [mm] 125/25 156/37 156/37 156/37 19/1 19/1 19/1 19/1 21/3 B2 [mm] 1/265 12/332 12/332 12/ / / / / /29 B3 [mm] phase TPE [mm] TP [mm] 125/ /36 156/ /385 2/25 2/25 2/25 2/25 3/51 3-phase TPE [mm] 167/3 188/37 188/3 213/3 38/1 38/1 38/1 38/1 - C1 [mm] 16/28 1/8 1/8 1/8 23/5 23/5 23/5 23/5 23/5 C5 [mm] 225/83 2/1 2/1 2/1 275/11 275/11 275/11 275/11 275/11 C6 [mm] L1 [mm] H1 [mm] H2 [mm] /3-phase TP [mm] -/613 -/718 -/776 -/76 -/881 -/881 -/925 -/925 -/158 H3 1-/3-phase TPE [mm] -/613 -/718 -/776 -/76 -/881 -/881 -/925 -/951 -/- H [mm] M M16 M16 M16 M16 M16 M16 M16 M16 M16 TP(E), TP(E)D pumps are primarily fitted with IE3 motors. See section Motors on pages 36 to. The dimension before the slash applies to the single-head pump, and the dimension after the slash applies to the twin-head pump. 73

74 Technical data DN 32 -pole, PN 6, 1, 16 TP, TPD, TPE, TPED, -pole, PN 6, 1, 16 TP, TPD, TPE, TPED 32-XXX/ H / -/ -3/ TP, TPE 32 Hz Q [m³/h] H / -1/ -8/ TP, TPE 32 Hz Q [m³/h] / /.8 -/. -1/.6-3/ / Q [m³/h] NPSH -/, -6/ Q [m³/h] NPSH / Eta [%] Q [m³/h] -/ -6/ -3/ Eta [%] Q [m³/h] -1/ -8/ -12/ Q [m³/h] Q [m³/h] Q [l/s] v [m/s] TM Q [l/s] v [m/s] TM2 28 Note: All curves apply to single-head pumps. For further information, see page. 7

75 Performance curves DN 32 -pole, PN 6, 1, 16 P B3 P AF H3 AE D1 B1 B2 Rp 1/ M L1 C5 H1 H2 H C1 B1 D1 B2 AE AF AE AF M M L1 C6 C5 H H1 H2 C1 TM TM Technical data TP 32-3/ -/ -6/ -8/ -1/ -12/ TPD TPE TPED Series IEC size 1-phase TP phase TP phase TPE phase TPE /3-phase TP.12/.12.25/.25.25/.25 -/.25 -/.37 -/.55 1-/3-phase TPE.37/-.37/-.37/-.25/-.37/-.55/.55 PN PN 6/1 PN 6/1 PN 6/1 PN 16 PN 16 PN 16 T min ; T max [ C] [-25;1] [-25;1] [-25;1] [-25;12] [-25;12] [-25;12] D1 [mm] /3-phase TP [mm] 118/118 11/11 11/11 -/11 -/11 -/11 1-/3-phase TPE [mm] 11/- 11/- 11/- 11/- 11/- 11/178 1-/3-phase TP [mm] 11/11 133/ /133 -/19 -/19 -/19 1-/3-phase TPE [mm] 1/- 1/- 1/- 1/- 1/- 1/167 AE 1-/3-phase TPE [mm] 15/- 15/- 15/- 15/- 15/- 15/132 AF 1-/3-phase TPE [mm] 15/- 15/- 15/- 15/- 15/- 15/132 P [mm] - 15/ B1 [mm] 75/18 1/222 1/ /26 125/26 1/321 B2 [mm] 75/18 1/222 1/ / /257 1/321 B3 [mm] phase TPE [mm] 1/26 1/225 1/225 1/26 1/26 1/321 TP [mm] 11/18 1/222 1/ /26 125/26 1/321 3-phase TPE [mm] /321 C1 [mm] 8/2 8/2 8/2 1/356 1/356 1/35 C5 [mm] 11/52 1/82 1/82 17/5 17/5 22/6 C6 [mm] L1 [mm] H1 [mm] H2 [mm] /3-phase TP [mm] 16/39 395/ /395 -/2 -/2 -/87 H3 1-/3-phase TPE [mm] 8/- 395/- 395/- 2/- 2/- 87/537 H [mm] M M12 M12 M12 M16 M16 M16 TP(E), TP(E)D pumps are primarily fitted with IE3 motors. See section Motors on pages 36 to. The dimension before the slash applies to the single-head pump, and the dimension after the slash applies to the twin-head pump. 75

76 Technical data DN -pole, PN 6, 1, 16 TP, TPD, TPE, TPED -XXX/ H / -6/ -3/ TP, TPE Hz Q [m³/h] H / -13/ -1/ TP, TPE Hz Q [m³/h].2.2-6/ / / -3/ / -1/ Q [m³/h] NPSH 3.5-9/ / -6/ Q [m³/h] NPSH Eta [%] Q [m³/h] -9/ -3/ -6/. Eta [%] Q [m³/h] -1/ -13/ -16/ Q [m³/h] Q [m³/h] Q [l/s] v [m/s] TM Q [l/s] v [m/s] TM Note: All curves apply to single-head pumps. For further information, see page. 76

77 Performance curves DN -pole, PN 6, 1, 16 P B3 P AF AE H3 D1 B1 B2 Rp 1/ M L1 C5 H1 H2 H C1 B1 D1 B2 AE AF AE AF M M L1 C6 C5 H H1 H2 C1 TM TM Technical data TP -3/ -6/ -9/ -1/ -13/ -16/ TPD - TPE TPED - Series IEC size 1-phase TP phase TP phase TPE phase TPE /3-phase TP.12/.12.25/.25.25/.25 -/.55 -/.75 -/1.1 1-/3-phase TPE.37/-.37/-.37/-.55/.55.75/.75 -/1.1 PN PN 6/1 PN 6/1 PN 16 PN 16 PN 16 PN 16 T min ; T max [ C] [-25;1] [-25;1] [-25;1] [-25;12] [-25;12] [-25;12] D1 [mm] 1-/3-phase TP [mm] 118/118 11/11 11/11 -/11 -/178 -/178 1-/3-phase TPE [mm] 11/- 11/- 11/- 11/178 11/178 -/178 1-/3-phase TP [mm] 11/11 133/19 133/133 -/19 -/11 -/11 1-/3-phase TPE [mm] 1/- 1/- 1/- 1/167 1/167 -/167 AE 1-/3-phase TPE [mm] 15/- 15/- 15/- 15/132 15/132 -/132 AF 1-/3-phase TPE [mm] 15/- 15/- 15/- 15/132 15/132 -/132 P [mm] B1 [mm] 85/18 1/- 1/222 13/273 19/325 19/325 B2 [mm] 75/18 1/- 1/ /267 1/321 1/321 B3 [mm] phase TPE [mm] 1/26 1/225 1/225 1/273 19/325 - TP [mm] 11/18 133/- 1/222 13/273 19/325 19/325 3-phase TPE [mm] / / /325 C1 [mm] 12/2 12/- 12/2 1/ 1/35 1/35 C5 [mm] 125/5 125/- 16/95 17/5 22/18 22/18 C6 [mm] L1 [mm] H1 [mm] / H2 [mm] /3-phase TP [mm] 19/ / /398 -/97 -/59 -/589 H3 1-/3-phase TPE [mm] 11/- 389/- 388/- 7/57 99/59 -/59 H [mm] M M12 M12 M12 M16 M16 M16 TP(E), TP(E)D pumps are primarily fitted with IE3 motors. See section Motors on pages 36 to. The dimension before the slash applies to the single-head pump, and the dimension after the slash applies to the twin-head pump. 77

78 Technical data DN -pole, PN 6, 1, 16 TP, TPD, TPE, TPED -XXX/ H / -9/ TP, TPE Hz H / -19/ TP, TPE Hz / -3/ / -13/ Q [m³/h].7-11/ / -9/ -6/ Q [m³/h] NPSH Q [m³/h] / -16/ -23/ -19/ Q [m³/h] NPSH / / -9/, -11/ Eta [%] Q [m³/h] -11/ -3/ -9/ -6/ Q [m³/h]. Eta [%] Q [m³/h] -13/ -16/ -19/ -23/ Q [m³/h] Q [l/s] v [m/s] TM Q [l/s] v [m/s] TM2 32 Note: All curves apply to single-head pumps. For further information, see page. 78

79 Performance curves DN -pole, PN 6, 1, 16 P B3 P AF H3 AE D1 B1 B2 Rp 1/ M L1 C5 H1 H2 H C1 B1 D1 B2 AE AF AE AF M M L1 C6 C5 H H1 H2 C1 TM TM Technical data TP -3/ -6/ -9/ -11/ -13/ -16/ -19/ -23/ TPD TPE TPED Series IEC size 1-phase TP phase TP phase TPE phase TPE /3-phase TP.25/.25.37/.37 -/.55 -/.75 -/1.1 -/1.5 -/2.2 -/3 1-/3-phase TPE.37/-.37/-.55/.55.75/.75 -/1.1 -/1.5 -/2.2 -/3 PN PN 6/1 PN 6/1 PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 T min ; T max [ C] [-25;1] [-25;1] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] D1 [mm] 1-/3-phase TP [mm] 11/12 11/11 -/11 -/178 -/178 -/178 -/198 -/198 1-/3-phase TPE [mm] 11/- 11/- 11/178 11/178 -/178 -/178 -/198 -/198 1-/3-phase TP [mm] 133/ /19 -/19 -/11 -/11 -/11 -/12 -/12 1-/3-phase TPE [mm] 1/- 1/- 1/167 1/167 -/167 -/167 -/177 -/177 AE 1-/3-phase TPE [mm] 15/- 15/- 15/132 15/132 -/132 -/132 -/132 -/132 AF 1-/3-phase TPE [mm] 15/- 15/- 15/132 15/132 -/132 -/132 -/132 -/132 P [mm] B1 [mm] 75/181 11/ /29 18/386 18/386 18/386 18/386 18/386 B2 [mm] 9/186 1/ /28 16/379 16/379 16/379 16/379 16/379 B3 [mm] phase TPE [mm] 1/26 1/225 1/29 18/ TP [mm] 133/ / /29 18/386 18/386 18/386 18/386 18/386 3-phase TPE [mm] /29 18/386 18/386 18/386 18/386 18/386 C1 [mm] 12/2 12/2 1/ 1/ 1/ 1/ 1/ 1/ C5 [mm] 1/6 1/6 17/52 22/123 22/123 22/123 22/123 22/123 C6 [mm] L1 [mm] H1 [mm] 82/ H2 [mm] /3-phase TP [mm] 8/16 52/ -/7 -/553 -/63 -/63 -/65 -/65 H3 1-/3-phase TPE [mm] 8/- /- 7/ /563 -/563 -/63 -/65 -/65 H [mm] M M12 M12 M16 M16 M16 M16 M16 M16 TP(E), TP(E)D pumps are primarily fitted with IE3 motors. See section Motors on pages 36 to. The dimension before the slash applies to the single-head pump, and the dimension after the slash applies to the twin-head pump. 79

80 Technical data DN 65 -pole, PN 6, 1, 16 TP, TPD, TPE, TPED 65-XXX/ H / -9/ -6/ -3/ TP, TPE 65 Hz Q [m³/h] -9/ -3/ -11/ -6/ Q [m³/h] NPSH 2.5-3/ H / -17/ -1/ -13/ TP, TPE 65 Hz Q [m³/h]. -2/ -13/ -17/ -1/ Q [m³/h] NPSH / /, -11/ Eta [%] Q [m³/h] -3/ -9/ -11/ -6/ Q [m³/h]. Eta [%] Q [m³/h] -2/ -17/ -13/ -1/ Q [m³/h] Q [l/s] v [m/s] TM Q [l/s] v [m/s] TM2 3 Note: All curves apply to single-head pumps. For further information, see page. 8

81 Performance curves DN 65 -pole, PN 6, 1, 16 P B3 P AF AE H3 D1 B1 B2 Rp 1/ M L1 C5 H1 H2 H C1 B1 D1 B2 AE AF AE AF M M L1 C6 C5 H H1 H2 C1 TM TM Technical data TP 65-3/ -6/ -9/ -11/ -13/ -1/ -17/ -2/ TPD TPE TPED Series IEC size 1-phase TP phase TP phase TPE phase TPE /3-phase TP.25/.25.55/.55 -/.75 -/1.1 -/1.5 -/2.2 -/3 -/ 1-/3-phase TPE.37/-.55/.55.75/.75 -/1.1 -/1.5 -/2.2 -/3 -/ PN PN 6/1 PN 6/1 PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 T min ; T max [ C] [-25;1] [-25;1] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] D1 [mm] /3-phase TP [mm] 11/11 11/11 -/178 -/178 -/178 -/198 -/198 -/22 1-/3-phase TPE [mm] 11/- 11/178 11/178 -/178 -/178 -/198 -/198 -/22 1-/3-phase TP [mm] 133/19 133/19 -/11 -/11 -/11 -/12 -/12 -/13 1-/3-phase TPE [mm] 1/- 1/167 1/167 -/167 -/167 -/177 -/177 -/188 AE 1-/3-phase TPE [mm] 15/- 15/132 15/15 -/132 -/132 -/132 -/132 -/15 AF 1-/3-phase TPE [mm] 15/- 15/132 15/15 -/132 -/132 -/132 -/132 -/15 P [mm] B1 [mm] 125/23 125/23 12/ /39 178/39 178/39 178/39 178/39 B2 [mm] 1/2 1/2 12/29 16/383 16/383 16/ 16/383 16/383 B3 [mm] phase TPE [mm] 1/2 1/2 12/ TP [mm] 133/2 133/2 12/ / / /39 178/ /383 3-phase TPE [mm] - 167/32 167/36 178/ / / / /365 C1 [mm] 16/2 16/2 1/ 1/52 1/52 1/52 1/52 1/52 C5 [mm] 17/63 17/63 18/65 238/ / / / /111 C6 [mm] L1 [mm] H1 [mm] H2 [mm] /3-phase TP [mm] 23/23 75/75 -/558 -/612 -/612 -/65 -/65 -/691 H3 1-/3-phase TPE [mm] 23/- 75/525 8/558 -/572 -/612 -/65 -/65 -/691 H [mm] M M16 M16 M16 M16 M16 M16 M16 M16 TP(E), TP(E)D pumps are primarily fitted with IE3 motors. See section Motors on pages 36 to. The dimension before the slash applies to the single-head pump, and the dimension after the slash applies to the twin-head pump. 81

82 Technical data DN 8 -pole, PN 6, 1, 16 TP, TPD, TPE, TPED 8-XXX/ H / -9/ -7/ -6/ -3/ TP, TPE 8 Hz Q [m³/h] -6/ -3/ -9/ -7/ -11/ Q [m³/h] NPSH 5-3/ H / -27/ -2/ -17/ -1/ TP, TPE 8 Hz Q [m³/h] -2/ -17/ -1/ -27/ -3/ Q [m³/h] NPSH 5-27/, 3/ / -7/ 9/, -11/ /, 17/ -2/ Eta [%] Q [m³/h] -6/ -9/ -11/ -7/ -3/ Eta [%] Q [m³/h] -17/ -1/ -3/ -27/ -2/ Q [m³/h] Q [m³/h] Q [l/s] v [m/s] TM Q [l/s] v [m/s] TM Note: All curves apply to single-head pumps. For further information, see page. 82

83 Performance curves DN 8 -pole, PN 6, 1, 16 P B3 P AF H3 AE H3 D1 B1 B2 Rp 1/ M L1 C5 H H1 H2 C1 B1 D1 B2 AE AF AE AF M M L1 C6 C5 H H1 H2 C1 TM TM Technical data TP 8-3/ -6/ -7/ -9/ -11/ -1/ -17/ -2/ -27/ -3/ TPD TPE TPED Series IEC size 1-phase TP phase TP phase TPE phase TPE /3-phase TP.37/.37.75/.75 -/1.1 -/1.5 -/2.2 -/3 -/ -/5.5 -/7.5 -/11 1-/3-phase TPE.37/-.75/.75 -/1.1 -/1.5 -/2.2 -/3 -/ -/5.5 -/7.5 -/11 PN PN 6/PN 1 PN 6/PN 1 PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 T min ; T max [ C] [-25;1] [-25;1] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] D1 [mm] /3-phase TP [mm] 12/11 178/178 -/178 -/178 -/198 -/198 -/22 -/26 -/26 -/31 1-/3-phase TPE [mm] 11/- 11/178 -/178 -/178 -/198 -/198 -/22 -/26 -/26 -/31 1-/3-phase TP [mm] 133/19 139/11 -/11 -/11 -/12 -/12 -/13 -/159 -/159 -/2 1-/3-phase TPE [mm] 1/- 1/167 -/167 -/167 -/177 -/177 -/188 -/213 -/213 -/38 AE 1-/3-phase TPE [mm] 15/- 15/ AF 1-/3-phase TPE [mm] 15/- 15/ P [mm] B1 [mm] 13/23 135/2 176/ / / /16 187/16 23/91 23/91 23/91 B2 [mm] 1/2 1/2 1/35 1/35 1/35 162/5 162/5 226/8 226/8 226/8 B3 [mm] phase TPE [mm] 1/2 1/ TP [mm] 133/23 139/2 176/ / / /16 187/16 23/91 23/91 23/91 3-phase TPE [mm] - 167/32 176/ / / /16 188/16 23/91 23/91 38/91 C1 [mm] 16/2 16/2 1/8 1/8 1/8 1/5 1/5 23/5 23/5 23/5 C5 [mm] 18/53 18/53 22/93 22/93 22/93 2/133 2/133 31/15 31/15 31/15 C6 [mm] L1 [mm] H1 [mm] H2 [mm] /3-phase TP [mm] 513/61 551/51 -/612 -/612 -/65 -/65 -/691 -/792 -/82 -/91 H3 1-/3-phase TPE [mm] 61/- 91/51 -/572 -/612 -/65 -/65 -/691 -/792 -/872 -/91 H [mm] M M16 M16 M16 M16 M16 M16 M16 M16 M16 M16 TP(E), TP(E)D pumps are primarily fitted with IE3 motors. See section Motors on pages 36 to. The dimension before the slash applies to the single-head pump, and the dimension after the slash applies to the twin-head pump. 83

84 Technical data DN 1 -pole, PN 6, 1, 16 TP, TPD, TPE, TPED 1-XXX/ H / -13/ -11/ -9/ -7/ -6/ -3/ TP, TPE 1 Hz Q [m³/h] 6-17/ -13/ 3-11/ 2-9/ 1-7/ -6/ -3/ Q [m³/h] NPSH 1-3/ Eta [%] /, -17/ -6/ -9/, -11/ -7/ Q [m³/h] -17/ -6/ -11/ -3/ -13/ -7/ -9/ Q [m³/h] Q [l/s] v [m/s] TM2 5 9 Note: All curves apply to single-head pumps. For further information, see page. 8

85 Performance curves DN 1 -pole, PN 6, 1, 16 P B3 P H3 AF AE H3 D1 B1 B2 Rp 1/ M L1 C5 H H1 H2 C1 B1 D1 B2 AE AF AE AF M M L1 C6 C5 H H1 H2 C1 TM TM Technical data TP 1-3/ -6/ -7/ -9/ -11/ -13/ -17/ TPD TPE TPED Series IEC size 1-phase TP phase TP phase TPE phase TPE /3-phase TP.55/ /1.1 -/1.5 -/2.2 -/3 -/ -/5.5 1-/3-phase TPE.55/.55 -/1.1 -/1.5 -/2.2 -/3 -/ -/5.5 PN PN 6/PN 1 PN 6/PN 1 PN 16 PN 16 PN 16 PN 16 PN 16 T min ; T max [ C] [-25;1] [-25;1] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] D1 [mm] /3-phase TP [mm] 11/11 178/178 -/178 -/198 -/198 -/22 -/26 1-/3-phase TPE [mm] 11/178 -/178 -/178 -/198 -/198 -/22 -/26 1-/3-phase TP [mm] 133/19 139/11 -/11 -/12 -/12 -/13 -/159 1-/3-phase TPE [mm] 1/167 -/167 -/167 -/177 -/177 -/188 -/213 AE 1-/3-phase TPE [mm] 15/132 -/ AF 1-/3-phase TPE [mm] 15/132 -/ P [mm] B1 [mm] 175/28 175/28 19/1 19/1 19/1 21/3 21/3 B2 [mm] 125/35 125/35 151/ / / /29 173/29 B3 [mm] phase TPE [mm] 175/ TP [mm] 175/28 175/28 19/1 19/1 19/1 21/3 21/3 3-phase TPE [mm] 175/3 175/3 19/1 19/1 19/1 21/3 213/3 C1 [mm] 2/28 2/28 23/5 23/5 23/5 23/5 23/5 C5 [mm] 225/83 225/83 2/11 275/11 275/11 275/11 275/11 C6 [mm] L1 [mm] H1 [mm] H2 [mm] /3-phase TP [mm] 525/ /625 -/63 -/676 -/676 -/773 -/796 H3 1-/3-phase TPE [mm] 525/575 -/585 -/63 -/676 -/676 -/773 -/796 H [mm] M M16 M16 M16 M16 M16 M16 M16 TP(E), TP(E)D pumps are primarily fitted with IE3 motors. See section Motors on pages 36 to. The dimension before the slash applies to the single-head pump, and the dimension after the slash applies to the twin-head pump. 85

86 Technical data DN 1 -pole, PN 6, 1, 16 TP, TPD, TPE, TPED 1-XXX/ H / -37/ -33/ -2/ -2/ TP, TPE 1 Hz Q [m³/h] -2/ -2/ -1/ -37/ -33/ Q [m³/h] NPSH /, -37/, -1/ 2 Eta [%] /, -2/ Q [m³/h] -1/ -2/ -33/ -2/ -37/ Q [m³/h] Q [l/s] v [m/s] TM Note: All curves apply to single-head pumps. For further information, see page. 86

87 Performance curves DN 1 -pole, PN 6, 1, 16 P B3 P AF H3 AE H3 D1 B1 B2 Rp 1/ M L1 C5 H H1 H2 C1 B1 D1 B2 AE AF AE AF M M L1 C6 C5 H H1 H2 C1 TM TM Technical data TP 1-2/ -2/ -33/ -37/ -1/ TPD TPE - TPED - Series IEC size 1-phase TP phase TP phase TPE phase TPE /3-phase TP -/7.5 -/11 -/15 -/18.5 -/22 1-/3-phase TPE -/7.5 -/11 -/15 -/ PN PN 16 PN 16 PN 16 PN 16 PN 16 T min ; T max [ C] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] D1 [mm] /3-phase TP [mm] -/26 -/31 -/31 -/363 -/363 1-/3-phase TPE [mm] -/26 -/31 -/31 -/31-1-/3-phase TP [mm] -/159 -/2 -/2 -/262 -/262 1-/3-phase TPE [mm] -/213 -/38 -/38 -/38 - AE 1-/3-phase TPE [mm] AF 1-/3-phase TPE [mm] P [mm] B1 [mm] 29/579 29/579 29/579 29/579 29/579 B2 [mm] 29/561 29/561 29/561 29/561 29/561 B3 [mm] phase TPE [mm] TP [mm] 29/579 29/579 29/579 29/579 29/579 3-phase TPE [mm] 29/579 38/579 38/579 38/579 - C1 [mm] 23/68 23/68 23/68 23/68 23/68 C5 [mm] 335/11 335/11 335/11 335/11 335/11 C6 [mm] L1 [mm] H1 [mm] H2 [mm] /3-phase TP [mm] -/858 -/95 -/128 -/12 -/193 H3 1-/3-phase TPE [mm] -/888 -/95 -/998 -/12 - H [mm] M M16 M16 M16 M16 M16 TP(E), TP(E)D pumps are primarily fitted with IE3 motors. See section Motors on pages 36 to. The dimension before the slash applies to the single-head pump, and the dimension after the slash applies to the twin-head pump. 87

88 Technical data DN 125 -pole, PN 6, 1, 16 TP, TPD, TPE, TPED 125-XXX/ H / TP, TPE 125 Hz H -2/ TP, TPE 125 Hz / -11/ / -32/ -2/ / Q [m³/h] 8-16/ / -13/ Q [m³/h] -2/ -21/ -32/ -2/ -36/ Q [m³/h] NPSH Q [m³/h] NPSH 6-32/, -36/, -2/ /, -13/, 16/ /, -2/ Eta [%] Q [m³/h] -13/ -11/ -16/ Q [m³/h] Eta [%] Q [m³/h] -21/ -36/ -2/ -32/ -2/ Q [m³/h] Q [l/s] v [m/s] TM Q [l/s] v [m/s] TM Note: All curves apply to single-head pumps. For further information, see page. 88

89 Performance curves DN 125 -pole, PN 6, 1, 16 P B3 P H3 AF AE H3 D1 B1 B2 Rp 1/ M L1 C5 H H1 H2 C1 B1 D1 B2 AE AF AE AF M M L1 C6 C5 H H1 H2 C1 TM TM Technical data TP / -13/ -16/ -21/ -2/ -32/ -36/ -2/ TPD TPE - - TPED - - Series IEC size 1-phase TP phase TP phase TPE phase TPE /3-phase TP -/ -/5.5 -/7.5 -/11 -/15 -/18.5 -/22 -/3 1-/3-phase TPE -/ -/5.5 -/7.5 -/11 -/15 -/ /- PN PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 T min ; T max [ C] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] D1 [mm] /3-phase TP [mm] -/22 -/26 -/26 -/31 -/31 -/363 -/363 -/2 1-/3-phase TPE [mm] -/22 -/26 -/26 -/31 -/31 -/31 - -/- 1-/3-phase TP [mm] -/13 -/159 -/159 -/2 -/2 -/262 -/262 -/3 1-/3-phase TPE [mm] -/188 -/213 -/213 -/38 -/38 -/38 - -/- AE 1-/3-phase TPE [mm] AF 1-/3-phase TPE [mm] P [mm] B1 [mm] 2/537 2/537 2/ / / / / /566 B2 [mm] 22/518 22/518 22/518 23/552 23/552 23/552 23/552 23/552 B3 [mm] phase TPE [mm] TP [mm] 2/537 2/537 2/ / / / /566 3/566 3-phase TPE [mm] 2/537 2/537 2/537 38/566 38/566 38/ C1 [mm] 23/68 23/68 23/68 23/68 23/68 23/68 23/68 23/68 C5 [mm] 31/8 31/8 31/8 /175 /175 /175 /175 /175 C6 [mm] L1 [mm] H1 [mm] H2 [mm] /3-phase TP [mm] -/85 -/877 -/927 -/1 -/178 -/192 -/113 -/12 H3 1-/3-phase TPE [mm] -/85 -/877 -/969 -/1 -/18 -/17 -/- -/- H [mm] M M16 M16 M16 M16 M16 M16 M16 M16 TP(E), TP(E)D pumps are primarily fitted with IE3 motors. See section Motors on pages 36 to. The dimension before the slash applies to the single-head pump, and the dimension after the slash applies to the twin-head pump. 89

90 Technical data DN 1 -pole, PN 6, 1, 16 TP, TPD, TPE, TPED 1-XXX/ H / -22/ -2/ -16/ -13/ TP, TPE 1 Hz Q [m³/h] -13/ -2/ -16/ -22/ -2/ Q [m³/h] NPSH /, -16/, -2/, -22/, -2/ 1 Eta [%] Q [m³/h] -2/ -16/ -2/ -13/ -22/ Q [m³/h] Q [l/s] v [m/s] TM Note: All curves apply to single-head pumps. For further information, see page. 9

91 Performance curves DN 1 -pole, PN 6, 1, 16 P B3 P AF H3 AE H3 D1 B1 B2 Rp 1/ M L1 C5 H H1 H2 C1 B1 D1 B2 AE AF AE AF M M L1 C6 C5 H H1 H2 C1 TM TM Technical data TP 1-13/ -16/ -2/ -22/ -2/ TPD TPE - TPED - Series IEC size 1-phase TP phase TP phase TPE phase TPE /3-phase TP -/7.5 -/11 -/15 -/18.5 -/22 1-/3-phase TPE -/7.5 -/11 -/15 -/ PN PN 16 PN 16 PN 16 PN 16 PN 16 T min ; T max [ C] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] D1 [mm] /3-phase TP [mm] -/267 -/31 -/31 -/363 -/363 1-/3-phase TPE [mm] -/26 -/31 -/31 -/31-1-/3-phase TP [mm] -/167 -/2 -/2 -/262 -/262 1-/3-phase TPE [mm] -/213 -/38 -/38 -/38 - AE 1-/3-phase TPE [mm] AF 1-/3-phase TPE [mm] P [mm] B1 [mm] 296/ / / / /583 B2 [mm] 237/ / / / /553 B3 [mm] phase TPE [mm] TP [mm] 296/ / / / /583 3-phase TPE [mm] 296/583 38/583 38/583 38/583 - C1 [mm] 23/68 23/68 23/68 23/68 23/68 C5 [mm] /153 /153 /153 /153 /153 C6 [mm] L1 [mm] H1 [mm] H2 [mm] /3-phase TP [mm] -/917 -/18 -/182 -/196 -/117 H3 1-/3-phase TPE [mm] -/966 -/18 -/152 -/178 -/- H [mm] M M16 M16 M16 M16 M16 TP(E), TP(E)D pumps are primarily fitted with IE3 motors. See section Motors on pages 36 to. The dimension before the slash applies to the single-head pump, and the dimension after the slash applies to the twin-head pump. 91

92 Technical data DN 1 -pole, PN 6, 1, 16 TP, TPD, TPE, TPED 1-XXX/ H / -3/ -28/ -26/ TP, TPE 1 Hz Q [m³/h] -28/ -26/ -39/ -3/ Q [m³/h] NPSH / 2 Eta [%] /, -3/, 39/ Q [m³/h] -39/ -26/ -28/ -3/ Q [m³/h] Q [l/s] v [m/s] TM Note: All curves apply to single-head pumps. For further information, see page. 92

93 Performance curves DN 1 -pole, PN 6, 1, 16 TM Technical data TP 1-26/ -28/ -3/ -39/ TPD TPE TPED Series IEC size 1-phase TP phase TP phase TPE phase TPE /3-phase TP -/18.5 -/22 -/3 -/37 1-/3-phase TPE -/18.5 -/- -/- -/- PN PN 16 PN 16 PN 16 PN 16 T min ; T max [ C] [-25;12] [-25;12] [-25;12] [-25;12] D1 [mm] /3-phase TP [mm] -/363 -/363 -/2 -/2 1-/3-phase TPE [mm] -/31 -/ - -/- -/- 1-/3-phase TP [mm] -/262 -/262 -/3 -/325 1-/3-phase TPE [mm] -/38 -/ - -/- -/- AE 1-/3-phase TPE [mm] AF 1-/3-phase TPE [mm] P [mm] 3 3 B1 [mm] 335/- 335/- 335/- 335/- B2 [mm] 288/- 288/- 288/- 288/- 1-phase TPE [mm] TP [mm] 335/- 335/- 335/- 335/- 3-phase TPE [mm] 335/- -/- -/- -/- L1 [mm] H1 [mm] H2 [mm] H3 1-/3-phase TP [mm] -/1113 -/116 -/1221 -/ /3-phase TPE [mm] -/195 -/ - -/- -/- TP(E), TP(E)D pumps are primarily fitted with IE3 motors. See section Motors on pages 36 to. The dimension before the slash applies to the single-head pump, and the dimension after the slash applies to the twin-head pump. 93

94 Technical data DN 2 -pole, PN 6, 1, 16 TP 2-XXX/ H / -32/ -27/ -2/ -22/ -18/ TP, TPE 2 Hz Q [m³/h] / -2/ -22/ -27/ -1/ -32/ Q [m³/h] NPSH /, -22/, -2/ -27/, 32/, -1/ Eta [%] Q [m³/h] -1/ -32/ -18/ -27/ -22/ -2/ Q [m³/h] Q [l/s] v [m/s] TM

95 Performance curves DN 2 -pole, PN 6, 1, 16 TM Technical data TP 2-18/ -22/ -2/ -27/ -32/ -1/ TPD TPE TPED Series IEC size 1-phase TP phase TP phase TPE phase TPE /3-phase TP -/22 -/3 -/37 -/5 -/55 -/75 1-/3-phase TPE -/- -/- -/- -/- -/- -/- PN PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 T min ; T max [ C] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] D1 [mm] /3-phase TP [mm] -/363 -/2 -/2 -/2 -/95 -/555 1-/3-phase TPE [mm] -/ - -/- -/- -/- -/- -/- 1-/3-phase TP [mm] -/262 -/3 -/325 -/325 -/392 -/32 1-/3-phase TPE [mm] -/ - -/- -/- -/- -/- -/- AE 1-/3-phase TPE [mm] AF 1-/3-phase TPE [mm] P [mm] B1 [mm] 393/- 393/- 393/- 393/- 393/- 393/- B2 [mm] 328/- 328/- 328/- 328/- 328/- 328/- 1-phase TPE [mm] TP [mm] 393/- 393/- 393/- 393/- 393/- 32/- 3-phase TPE [mm] -/- -/- -/- -/- -/- -/- L1 [mm] H1 [mm] H2 [mm] H3 1-/3-phase TP [mm] -/1252 -/139 -/1321 -/1381 -/189 -/192 1-/3-phase TPE [mm] -/ - -/- -/- -/- -/- -/- TP(E), TP(E)D pumps are primarily fitted with IE3 motors. See section Motors on pages 36 to. The dimension before the slash applies to the single-head pump, and the dimension after the slash applies to the twin-head pump. 95

96 Technical data DN 2 -pole, PN 16 TP 2-XXX/ H / -59/ -53/ -7/ -/ -36/ -33/ TP, TPE 2 Hz Q [m³/h] 1-66/ -36/ -33/ -/ -7/ -53/ -59/ Q [m³/h] NPSH 1-7/, -53/, -59/, -66/ Eta [%] /, -36/, -/ Q [m³/h] -33/ -36/ -/ -7/ -53/ -66/ -59/ Q [m³/h] Q [l/s] v [m/s] TM

97 Performance curves DN 2 -pole, PN 16 TM Technical data TP 2-33/ -36/ -/ -7/ -53/ -59/ -66/ TPD TPE TPED Series IEC size 1-phase TP phase TP phase TPE phase TPE /3-phase TP -/37 -/5 -/55 -/75 -/9 -/11 -/132 1-/3-phase TPE -/- -/- -/- -/- -/- -/- -/- PN PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 T min ; T max [ C] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] D1 [mm] /3-phase TP [mm] -/2 -/2 -/95 -/555 -/555 -/61 -/61 1-/3-phase TPE [mm] -/- -/- -/- -/- -/- -/- -/- 1-/3-phase TP [mm] -/325 -/325 -/392 -/32 -/32 -/95 -/95 1-/3-phase TPE [mm] -/- -/- -/- -/- -/- -/- -/- AE 1-/3-phase TPE [mm] AF 1-/3-phase TPE [mm] P [mm] B1 [mm] 23/- 23/- 23/- 23/- 23/- 23/- 23/- B2 [mm] 368/- 368/- 368/- 368/- 368/- 368/- 368/- 1-phase TPE [mm] TP [mm] 23/- 23/- 23/- 32/- 32/- 95/- 95/- 3-phase TPE [mm] -/- -/- -/- -/- -/- -/- -/- L1 [mm] H1 [mm] H2 [mm] H3 1-/3-phase TP [mm] -/1326 -/1386 -/19 -/197 -/167 -/1639 -/ /3-phase TPE [mm] -/- -/- -/- -/- -/- -/- -/- TP(E), TP(E)D pumps are primarily fitted with IE3 motors. See section Motors on pages 36 to. The dimension before the slash applies to the single-head pump, and the dimension after the slash applies to the twin-head pump. 97

98 Technical data DN 2 -pole, PN 1 TP 2-XXX/ H 36-39/ TP 2 Hz 32-31/ / Q [m³/h] 6-28/ -31/ -39/ 3 2 NPSH Q [m³/h] Eta [%] Q [m³/h] -39/ -28/ -31/ Q [m³/h] Q [l/s] v [m/s] TM

99 Performance curves DN 2 -pole, PN 1 P H3 D1D Rp 3/8 L3 L1 H1 H2 L2 D1S C2 C8 Rp 3/8 C8 C7 ø B8 B9 B1 B2 B7 TM2 839 Technical data TP 2-28/ -31/ -39/ TPD TPE TPED Series 1-phase TP IEC size 3-phase TP 225 M 2 M 28 S 1-phase TPE phase TPE PN T min ; T max [ C] [-25;12] [-25;12] [-25;12] D1 D /D1 S [mm] 2/3 2/3 2/3 [mm] [mm] P [mm] B1 [mm] B2 [mm] [mm] B7 [mm] B8 [mm] B9 [mm] C2 [mm] C7 [mm] C8 [mm] [mm] L1 [mm] L2 [mm] L3 [mm] H1 [mm] H2 [mm] H3 [mm] TP(E), TP(E)D pumps are primarily fitted with IE3 motors. See section Motors on pages 36 to. 99

100 Technical data DN pole, PN 16 TP, TPD, TPE, TPED, 6-pole, PN 16 TP, TPD 125-XXX/6 H /6-1/6-11/6-9/6-7/6-6/6 TP 125 Hz Q [m³/h] 8-17/ /6-11/6 3-9/6 2-7/6-6/ Q [m³/h] NPSH 2.5-1/6, -17/ /6, -11/6-6/6, -7/6. Eta [%] Q [m³/h] -7/6-6/6-1/6-17/6-9/6-11/ Q [m³/h] Q [l/s] v [m/s] TM Note: All curves apply to single-head pumps. For further information, see page. 1

101 Performance curves DN pole, PN 16 P B3 P AF H3 AE H3 D1 B1 B2 Rp 1/ M L1 C5 H H1 H2 C1 B1 D1 B2 AE AF AE AF M M L1 C6 C5 H H1 H2 C1 TM TM Technical data TP 125-6/6-7/6-9/6-11/6-1/6-17/6 TPD TPE TPED Series IEC size 1-phase TP phase TP phase TPE phase TPE /3-phase TP -/1.5 -/2.2 -/3 -/ -/5.5 -/7.5 1-/3-phase TPE -/- -/- -/- -/- -/- -/- PN PN 16 PN 16 PN 16 PN 16 PN 16 PN 16 T min ; T max [ C] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] [-25;12] D1 [mm] /3-phase TP [mm] -/23 -/227 -/267 -/267 -/267 -/32 1-/3-phase TPE [mm] -/- -/- -/- -/- -/- -/- 1-/3-phase TP [mm] -/135 -/18 -/167 -/167 -/167 -/197 1-/3-phase TPE [mm] -/- -/- -/- -/- -/- -/- AE 1-/3-phase TPE [mm] AF 1-/3-phase TPE [mm] P [mm] B1 [mm] 2/537 2/ / / / /566 B2 [mm] 22/518 22/518 23/552 23/552 23/552 23/552 B3 [mm] phase TPE [mm] TP [mm] 2/537 2/ / / / /566 3-phase TPE [mm] C1 [mm] 23/68 23/68 23/68 23/68 23/68 23/68 C5 [mm] 31/8 31/8 /175 /175 /175 /175 C6 [mm] L1 [mm] H1 [mm] H2 [mm] /3-phase TP [mm] -/829 -/853 -/876 -/91 -/91 -/111 H3 1-/3-phase TPE [mm] -/- -/- -/- -/- -/- -/- H [mm] M M16 M16 M16 M16 M16 M16 The dimension before the slash applies to the single-head pump, and the dimension after the slash applies to the twin-head pump. 11

102 Technical data DN 1 6-pole, PN 16 TP, TPD 1-XXX/6 H /6-9/6-7/6-6/6 TP 1 Hz Q [m³/h] -11/6-9/ /6-7/ Q [m³/h] NPSH /6, -7/6, -9/6, -11/ Eta [%] Q [m³/h] -11/6-9/6-7/6-6/ Q [m³/h] Q [l/s] v [m/s] TM Note: All curves apply to single-head pumps. For further information, see page. 12

103 Performance curves DN 1 6-pole, PN 16 P B3 P H3 AF AE H3 D1 B1 B2 Rp 1/ M L1 C5 H H1 H2 C1 B1 D1 B2 AE AF AE AF M M L1 C6 C5 H H1 H2 C1 TM TM Technical data TP 1-6/6-7/6-9/6-11/6 TPD TPE TPED Series IEC size 1-phase TP phase TP phase TPE phase TPE /3-phase TP -/2.2 -/3 -/ -/5.5 1-/3-phase TPE -/- -/- -/- -/- PN PN 16 PN 16 PN 16 PN 16 T min ; T max [ C] [-25;12] [-25;12] [-25;12] [-25;12] D1 [mm] /3-phase TP [mm] -/227 -/267 -/267 -/267 1-/3-phase TPE [mm] -/- -/- -/- -/- 1-/3-phase TP [mm] -/18 -/167 -/167 -/167 1-/3-phase TPE [mm] -/- -/- -/- -/- AE 1-/3-phase TPE [mm] AF 1-/3-phase TPE [mm] P [mm] B1 [mm] 296/ / / /583 B2 [mm] 237/ / / /553 B3 [mm] phase TPE [mm] TP [mm] 296/ / / /583 3-phase TPE [mm] C1 [mm] 23/68 23/68 23/68 23/68 C5 [mm] /153 /153 /153 /153 C6 [mm] L1 [mm] H1 [mm] H2 [mm] H3 1-/3-phase TP [mm] -/862 -/879 -/917 -/917 1-/3-phase TPE [mm] -/- -/- -/- -/- H [mm] M M16 M16 M16 M16 The dimension before the slash applies to the single-head pump, and the dimension after the slash applies to the twin-head pump. 13

104 Technical data DN 1 2-pole, PN 25 TP, 2-pole, PN 25 TP 1-XXX/2 H /2-82/2 TP 1 Hz H /2-153/2 TP 1 Hz 7 6-7/2-62/ /2-118/2-1/ Q [m³/h] 7-96/ /2-62/2-7/ Q [m³/h] NPSH Eta [%] Q [m³/h] -82/2-62/2-7/2-96/ Q [m³/h] Q [m³/h] /2-1/2-153/2-1/2-168/ Q [m³/h] NPSH Eta [%] Q [m³/h] -1/2-118/2-1/2-153/2-168/ Q [m³/h] Q [l/s] v [m/s] TM Q [l/s] v [m/s] TM

105 Performance curves DN 1 2-pole, PN 25 Rp 1/2 P H2 H3 D1D H1 D1S Rp 1/2 L1 B8 B9 B6 C C9 ø C3 B5 B1 B2 B7 TM2 83 Technical data TP 1-62/2-7/2-82/2-96/2-1/2-118/2-1/2-153/2-168/2 TPD TPE TPED Series 1-phase TP IEC size 3-phase TP 2 L 225 M 2 M 28 S 28 S 28 M 315 S 315 M 315 L 1-phase TPE phase TPE PN T min ; T max [ C] [;1] [;1] [;1] [;1] [;1] [;1] [;1] [;1] [;1] D1 D /D1 S [mm] 1/125 1/125 1/125 1/125 1/125 1/125 1/125 1/125 1/125 [mm] [mm] P [mm] B1 [mm] B2 [mm] [mm] B5 [mm] B6 [mm] B7 [mm] B8 [mm] B9 [mm] C3 [mm] C [mm] C9 [mm] [mm] L1 [mm] H1 [mm] H2 [mm] H3 [mm] TP(E), TP(E)D pumps are primarily fitted with IE3 motors. See section Motors on pages 36 to. 15

106 Technical data DN 1 -pole, PN 25 TP, -pole, PN 25 TP 1-XXX/ H / -22/ -19/ TP 1 Hz H / -38/ -32/ -27/ TP 1 Hz Q [m³/h] Q [m³/h] / -22/ -26/ / -38/ -32/ -27/ Q [m³/h] NPSH Q [m³/h] NPSH Eta [%] Q [m³/h] -22/ -19/ -26/ Q [m³/h] Eta [%] Q [m³/h] -2/ -27/ -38/ -32/ Q [m³/h] Q [l/s] v [m/s] TM Q [l/s] v [m/s] TM

107 Performance curves DN 1 -pole, PN 25 Rp 1/2 P H2 H3 D1D H1 D1S Rp 1/2 L1 B8 B9 B6 C C9 ø C3 B5 B1 B2 B7 TM2 83 Technical data TP 1-19/ -22/ -26/ -27/ -32/ -38/ -2/ TPD TPE TPED Series 1-phase TP IEC size 3-phase TP 132 S 132 M 16 M 16 M 16 L 18 M 18 L 1-phase TPE phase TPE PN T min ; T max [ C] [;1] [;1] [;1] [;1] [;1] [;1] [;1] D1 D /D1 S [mm] 1/125 1/125 1/125 1/125 1/125 1/125 1/125 [mm] [mm] P [mm] B1 [mm] B2 [mm] [mm] B5 [mm] B6 [mm] B7 [mm] B8 [mm] B9 [mm] C3 [mm] C [mm] C9 [mm] [mm] L1 [mm] H1 [mm] H2 [mm] H3 [mm] TP(E), TP(E)D pumps are primarily fitted with IE3 motors. See section Motors on pages 36 to. 17

108 Technical data DN 125 -pole, PN 25 TP 125-XXX/ H / -2/ TP 125 Hz H 5-3/ -37/ TP 125 Hz / / -28/ Q [m³/h] 1-2/ / -1/ Q [m³/h] NPSH Q [m³/h] -28/ -3/ -37/ -31/ NPSH Q [m³/h] Eta [%] Q [m³/h] -2/ -2/ -1/ Q [m³/h] 2 6 Q [l/s] v [m/s] TM Eta [%] Q [m³/h] -3/ -37/ -28/ -31/ Q [m³/h] Q [l/s] TM

109 Performance curves DN 125 -pole, PN 25 Rp 1/2 P H2 H3 D1D H1 D1S Rp 1/2 L1 B8 B9 B6 C C9 ø C3 B5 B1 B2 B7 TM2 83 Technical data TP 125-1/ -2/ -2/ -28/ -31/ -37/ -3/ TPD TPE TPED Series 1-phase TP IEC size 3-phase TP 132 M 16 M 16 L 16 L 18 M 18 L 2 L 1-phase TPE phase TPE PN T min ; T max [ C] [;1] [;1] [;1] [;1] [;1] [;1] [;1] D1 D /D1 S [mm] 125/1 125/1 125/1 125/1 125/1 125/1 125/1 [mm] [mm] P [mm] B1 [mm] B2 [mm] [mm] B5 [mm] B6 [mm] B7 [mm] B8 [mm] B9 [mm] C3 [mm] C [mm] C9 [mm] [mm] L1 [mm] H1 [mm] H2 [mm] H3 [mm] TP(E), TP(E)D pumps are primarily fitted with IE3 motors. See section Motors on pages 36 to. 19

110 Technical data DN 1 -pole, PN 25 TP 1-XXX/ H 65 TP 1-6/ 6 Hz 55-53/ 5-3/ 35-3/ -32/ 3-27/ / Q [m³/h] 7 6-6/ -53/ -3/ 3-3/ -32/ 2-27/ -2/ 1 NPSH Q [m³/h] Eta [%] Q [m³/h] -32/ -3/ -2/ -3/ -6/ -53/ -27/ Q [m³/h] Q [l/s] v [m/s] TM

111 Performance curves DN 1 -pole, PN 25 Rp 1/2 P H2 H3 D1D H1 D1S Rp 1/2 L1 B8 B9 B6 C C9 ø C3 B5 B1 B2 B7 TM2 83 Technical data TP 1-2/ -27/ -32/ -3/ -3/ -53/ -6/ TPD TPE TPED Series 1-phase TP IEC size 3-phase TP 18 M 18 L 2 L 225 S 225 M 2 M 28 S 1-phase TPE phase TPE PN T min ; T max [ C] [;1] [;1] [;1] [;1] [;1] [;1] [;1] D1 D /D1 S [mm] 1/2 1/2 1/2 1/2 1/2 1/2 1/2 [mm] [mm] P [mm] B1 [mm] B2 [mm] [mm] B5 [mm] B6 [mm] B7 [mm] B8 [mm] B9 [mm] C3 [mm] C [mm] C9 [mm] [mm] L1 [mm] H1 [mm] H2 [mm] H3 [mm] TP(E), TP(E)D pumps are primarily fitted with IE3 motors. See section Motors on pages 36 to. 111

112 Technical data DN 2 -pole, PN 25 TP 2-XXX/ H / -38/ -28/ -26/ TP 2 Hz Q [m³/h] -2/ -28/ -38/ H / -56/ -51/ -/ TP 2 Hz Q [m³/h] -62/ -56/ -51/ -/ 2-26/ 2 1 NPSH Q [m³/h] Eta [%] Q [m³/h] -2/ -38/ -26/ -28/ Q [m³/h] 1 1 Q [l/s] TM Q [m³/h] NPSH Eta [%] Q [m³/h] -51/ -/ -62/ -56/ Q [m³/h] 1 1 Q [l/s] v [m/s] TM

113 Performance curves DN 2 -pole, PN 25 Rp 1/2 P H2 H3 D1D H1 D1S Rp 1/2 L1 B8 B9 B6 C C9 ø C3 B5 B1 B2 B7 TM2 83 Technical data TP 2-26/ -28/ -38/ -2/ -/ -51/ -56/ -62/ TPD TPE TPED Series 1-phase TP IEC size 3-phase TP 2 L 225 S 225 M 2 M 2 M 28 S 28 M 315 S 1-phase TPE phase TPE PN T min ; T max [ C] [;1] [;1] [;1] [;1] [;1] [;1] [;1] [;1] D1 D /D1 S [mm] 2/2 2/2 2/2 2/2 2/2 2/2 2/2 2/2 [mm] [mm] P [mm] B1 [mm] B2 [mm] [mm] B5 [mm] B6 [mm] B7 [mm] B8 [mm] B9 [mm] C3 [mm] C [mm] C9 [mm] [mm] L1 [mm] H1 [mm] H2 [mm] H3 [mm] TP(E), TP(E)D pumps are primarily fitted with IE3 motors. See section Motors on pages 36 to. 113

114 Technical data DN 2 -pole, PN 25 TP 2-XXX/ H / -32/ -27/ TP 2 Hz Q [m³/h] -32/ -27/ -37/ NPSH Q [m³/h] H / -6/ -5/ -9/ TP 2 Hz Q [m³/h] -9/ -66/ -6/ -5/ NPSH Q [m³/h] Eta [%] Q [m³/h] -27/ -37/ -32/ Q [m³/h] Eta [%] Q [m³/h] -6/ -66/ -9/ -5/ Q [m³/h] Q [l/s] v [m/s] TM Q [l/s] v [m/s] TM

115 Performance curves DN 2 -pole, PN 25 Rp 1/2 P H2 H3 D1D H1 D1S Rp 1/2 L1 B8 B9 B6 C C9 ø C3 B5 B1 B2 B7 TM2 83 Technical data TP 2-27/ -32/ -37/ -9/ -5/ -6/ -66/ TPD TPE TPED Series 1-phase TP IEC size 3-phase TP 225 M 2 M 28 S 28 M 315 S 315 M 315 M 1-phase TPE phase TPE PN T min ; T max [ C] [;1] [;1] [;1] [;1] [;1] [;1] [;1] D1 D /D1 S [mm] 2/3 2/3 2/3 2/3 2/3 2/3 2/3 [mm] [mm] P [mm] B1 [mm] B2 [mm] [mm] B5 [mm] B6 [mm] B7 [mm] B8 [mm] B9 [mm] C3 [mm] C [mm] C9 [mm] [mm] L1 [mm] H1 [mm] H2 [mm] H3 [mm] TP(E), TP(E)D pumps are primarily fitted with IE3 motors. See section Motors on pages 36 to. 115

116 Technical data DN 3 -pole, PN 25 TP 3-XXX/ H / -67/ -59/ TP 3 Hz Q [m³/h] / -59/ -7/ 1 NPSH Q [m³/h] Eta [%] Q [m³/h] -7/ -59/ -67/ Q [m³/h] Q [l/s] TM

117 Performance curves DN 3 -pole, PN 25 Rp 1/2 P H2 H3 D1D Rp 1/2 L1 H1 D1S B8 B9 B6 C C9 ø C3 B5 B1 B2 B7 TM2 83 Technical data TP 3-59/ -67/ -7/ TPD TPE TPED Series 1-phase TP IEC size 3-phase TP 315 L phase TPE phase TPE PN T min ; T max [ C] [;1] [;1] [;1] D1 D /D1 S [mm] 3/3 3/3 3/3 [mm] [mm] P [mm] B1 [mm] B2 [mm] [mm] B5 [mm] B6 [mm] B7 [mm] B8 [mm] B9 [mm] C3 [mm] C [mm] C9 [mm] [mm] L1 [mm] H1 [mm] H2 [mm] H3 [mm]

118 Technical data DN -pole, PN 25 TP -XXX/ H / -51/ -7/ TP Hz Q [m³/h] H / -72/ -67/ TP Hz Q [m³/h] 6-76/ 3 2-5/ -51/ -7/ 3-72/ -67/ Q [m³/h] NPSH 1 1 NPSH Q [m³/h] Eta [%] Q [m³/h] -7/ -51/ -5/ Q [m³/h] 2 Eta [%] Q [m³/h] -67/ -72/ -76/ Q [m³/h] Q [l/s] v [m/s] TM Q [l/s] v [m/s] TM

119 Performance curves DN -pole, PN 25 P Rp 1/2 H3 PN H1 H2 PN D1D Rp 1/2 L1 D1S B6 C ø C9 C3 B5 B9 B8 B2 B1 B7 TM Technical data TP -7/ -51/ -5/ -67/ -72/ -76/ TPD TPE TPED Series 1-phase TP IEC size 3-phase TP phase TPE phase TPE PN T min ; T max [ C] [;1] [;1] [;1] [;1] [;1] [;1] D1 D /D1 S [mm] / / / / / / [mm] [mm] P [mm] B1 [mm] B2 [mm] [mm] B5 [mm] B6 [mm] B7 [mm] B8 [mm] B9 [mm] C3 [mm] C [mm] C9 [mm] [mm] L1 [mm] H1 [mm] H2 [mm] H3 [mm]

120 Weights and shipping volume TP, TPD, TPE, TPED TP, TPD, TPE, TPED, 2-pole, PN 6, 1, 16 Connection Weights Pump type D1 D D1 S Shipping volume [m 3 ] Net [kg] Gross [kg] TP/TPD TPE/TPED TP/TPD TPE/TPED TP/TPD TPE/TPED TP 25-/2 R G 1/2 G 1/2 7/- - 8/- -.2/- - TP 25-9/2 R G 1/2 G 1/2 8/- 11/- 9/- 13/-.2/-.36/- TP 32-/2 R G 2 G 2 8/- - 9/- -.2/- - TP 32-9/2 R G 2 G 2 8/- 12/- 9/- 1/-.2/-.36/- TP, TPD 32-6/2 DN 32 DN 32 16/32 22/39 17/33 25/3.36/.72.6/.151 TP, TPD 32-12/2 DN 32 DN 32 19/38 21/2 2/ 22/.36/.72.56/.72 TP, TPD 32-1/2 DN 32 DN 32 23/5 29/59 26/57 33/62.6/.82.6/.151 TP, TPD 32-18/2 DN 32 DN 32 2/5 29/59 27/57 32/62.6/.82.6/.82 TP, TPD 32-23/2 DN 32 DN 32 25/5 1/81 28/57 5/85.6/.82.91/.221 TP, TPD 32-2/2 DN 32 DN 32 2/86 /11 7/11 62/ / /.3912 TP, TPD 32-2/2 DN 32 DN 32 6/93 52/15 51/19 57/ / /.3912 TP, TPD 32-32/2 DN 32 DN 32 51/1 57/11 57/12 62/133.18/ /.3912 TP, TPD 32-38/2 DN 32 DN 32 63/127 65/13 68/1 7/19.18/.58.18/.518 TP, TPD 32-6/2 DN 32 DN 32 76/151 79/157 82/169 85/ / /.518 TP, TPD 32-58/2 DN 32 DN 32 9/18 95/189 16/ / / /.518 TP -/2 DN DN 12/- - 13/- -.2/- - TP, TPD -6/2 DN DN 2/2 23/8 21/3 25/52.36/.72.56/.72 TP -9/2 DN DN 12/- 17/- 13/- 18/-.2/-.25/- TP, TPD -12/2 DN DN 2/1 22/6 21/3 2/.36/.72.56/.72 TP -18/2 DN DN 2/- 29/- 25/- 32/-.36/-.6/- TP, TPD -19/2 DN DN 29/5 /82 32/59 8/87.6/ /.221 TP, TPD -23/2 DN DN 36/56 6/81 39/61 9/86.6/ /.221 TP, TPD -27/2 DN DN 39/7 37/75 2/75 /8.6/ /.221 TP, TPD -2/2 DN DN 53/17 58/118 58/12 6/136.18/ /.3912 TP, TPD -3/2 DN DN 65/13 66/133 7/18 72/152.18/.58.18/.518 TP, TPD -36/2 DN DN 7/1 73/16 75/158 78/165.18/.58.18/.518 TP, TPD -7/2 DN DN 9/183 95/192 15/21 113/ / /.518 TP, TPD -58/2 DN DN 1/211 16/ / / / /.518 TP, TPD -6/2 DN DN 2/5 2/ 21/8 28/53.56/.72.6/.151 TP, TPD -12/2 DN DN 28/56 /83 29/58 1/85.56/.72.91/.221 TP, TPD -18/2 DN DN 28/56 1/83 29/58 5/86.56/.72.91/.221 TP, TPD -16/2 DN DN 7/9 53/16 52/111 6/ / /.3912 TP, TPD -19/2 DN DN 8/98 5/11 53/11 6/ / /.3912 TP, TPD -2/2 DN DN 5/18 59/119 59/125 6/137.18/ /.3912 TP, TPD -29/2 DN DN 65/131 67/13 7/19 72/153.18/.58.18/.518 TP, TPD -36/2 DN DN 71/1 7/1 76/161 8/168.18/.58.18/.518 TP, TPD -3/2 DN DN 86/17 91/182 11/191 19/21.18/.58.18/.518 TP, TPD -/2 DN DN 112/228 11/ /27 132/ / /.518 TP, TPD -57/2 DN DN 19/33 181/ /32 199/ / /1.52 TP, TPD -71/2 DN DN 179/363 18/ /38 23/ / /1.52 TP, TPD -83/2 DN DN 181/367 29/22 198/ /8.728/ /1.52 TP, TPD -9/2 DN DN 196/ /8 222/8 2/7.728/ /1.52 TP, TPD 65-6/2 DN 65 DN 65 26/53 3/59 27/56 33/63.56/.1.6/.151 TP, TPD 65-12/2 DN 65 DN 65 31/63 /86 32/65 2/9.56/.1.91/.221 TP, TPD 65-18/2 DN 65 DN 65 38/76 5/92 1/79 8/95.66/.1.91/.221 TP, TPD 65-19/2 DN 65 DN 65 57/116 63/126 63/132 68/15.18/ /.3912 TP, TPD 65-23/2 DN 65 DN 65 69/139 71/12 7/156 76/161.18/.58.18/.518 TP, TPD 65-26/2 DN 65 DN 65 7/19 77/155 79/166 82/173.18/.58.18/.518 TP, TPD 65-3/2 DN 65 DN 65 89/178 93/187 1/ /26.18/.58.18/.518 TP, TPD 65-1/2 DN 65 DN 65 13/26 15/21 118/22 123/229.18/.58.18/.518 TP, TPD 65-6/2 DN 65 DN /31 182/ /331 21/ / /1.52 TP, TPD 65-5/2 DN 65 DN 65 18/ / /39 2/5.728/ /1.52 TP, TPD 65-66/2 DN 65 DN /373 21/27 199/39 228/53.728/ /1.52 TP, TPD 65-72/2 DN 65 DN /2 223/5 216/29 22/81.728/ /1.52 TP, TPD 65-93/2 DN 65 DN 65 35/699-36/ / TP, TPD 8-12/2 DN 8 DN 8 3/83 52/1 /86 57/16.66/.1.91/.37 12

121 Weights and shipping volume TP, TPD, TPE, TPED Pump type Connection Weights Shipping volume [m 3 ] Net [kg] Gross [kg] D1 D D1 S TP/TPD TPE/TPED TP/TPD TPE/TPED TP/TPD TPE/TPED TP, TPD 8-1/2 DN 8 DN 8 61/12 66/13 7/11 78/151.18/ /.3912 TP, TPD 8-18/2 DN 8 DN 8 65/132 7/1 78/19 88/18.18/.58.18/.67 TP, TPD 8-21/2 DN 8 DN 8 78/157 8/162 9/17 9/192.18/.58.18/.518 TP, TPD 8-2/2 DN 8 DN 8 93/187 97/195 15/2 118/225.18/ /.518 TP, TPD 8-2/2 DN 8 DN 8 11/ / /23 136/ / /.518 TP, TPD 8-33/2 DN 8 DN 8 18/3 181/37 169/33 23/2.728/ /.67 TP, TPD 8-/2 DN 8 DN 8 16/ /377 18/356 25/25.728/ /.67 TP, TPD 8-52/2 DN 8 DN 8 176/39 215/27 197/ /77.728/ /1.52 TP, TPD 8-57/2 DN 8 DN 8 25/7 228/53 226/57 29/3.728/ /1.52 TP, TPD 8-7/2 DN 8 DN 8 3/ / / TP, TPD 1-12/2 DN 1 DN 1 53/18 61/12 55/113 66/13.1/ /.37 TP, TPD 1-16/2 DN 1 DN 1 93/196 95/22 17/26 19/ / /.67 TP, TPD 1-2/2 DN 1 DN 1 18/ / /276 13/ / /.67 TP, TPD 1-2/2 DN 1 DN 1 122/25 127/26 136/3 19/31.728/ /.67 TP, TPD 1-2/2 DN 1 DN 1 175/351 26/13 199/1 23/63.728/ /1.52 TP, TPD 1-31/2 DN 1 DN 1 2/1 29/2 228/6 233/7.728/ /1.52 TP, TPD 1-36/2 DN 1 DN 1 27/1 23/68 23/6 257/ / /1.52 TP, TPD 1-39/2 DN 1 DN 1 221/3 27/95 2/93 27/55.728/ /1.52 TP, TPD 1-8/2 DN 1 DN 1 38/771-25/ /1.8 - The dimension before the slash applies to the single-head pump, and the dimension after the slash applies to the twin-head pump. TP, TPD, TPE, TPED, -pole, PN 6, 1, 16 Connection Weights Pump type D1 D D1 S Net [kg] Gross [kg] Shipping volume [m 3 ] TP/TPD TPE/TPED TP/TPD TPE/TPED TP/TPD TPE/TPED TP, TPD 32-3/ DN 32 DN 32 15/3 21/38 16/31 2/2.36/.72.6/.151 TP, TPD 32-/ DN 32 DN 32 25/32 29/5 28/33 32/58.6/.72.6/.151 TP, TPD 32-6/ DN 32 DN 32 25/ 29/5 28/53 32/58.36/.82.6/.151 TP, TPD 32-8/ DN 32 DN 32 35/69 36/7 /86 8/92.138/ /.3912 TP, TPD 32-1/ DN 32 DN 32 36/71 37/75 1/88 9/92.138/ /.3912 TP, TPD 32-12/ DN 32 DN 32 9/9 8/96 55/11 61/ / /.3912 TP, TPD -3/ DN DN 17/33 23/1 18/3 26/.36/.72.6/.151 TP -6/ DN DN 22/2 27/- 23/3 3/-.36/.72.6/- TP, TPD -9/ DN DN 28/ 32/9 32/56 36/5.76/ /.151 TP, TPD -1/ DN DN 1/83 2/85 5/99 5/13.138/ /.3912 TP, TPD -13/ DN DN 7/98 58/12 53/11 71/ / /.3912 TP, TPD -16/ DN DN 53/11 6/131 59/126 71/1.2176/ /.3912 TP, TPD -3/ DN DN 2/6 3/51 25/8 33/55.36/.72.6/.151 TP, TPD -6/ DN DN 25/ 28/56 26/52 3/61.56/.72.56/.72 TP, TPD -9/ DN DN 3/87 /89 7/13 56/16.138/ /.3912 TP, TPD -11/ DN DN 55/115 66/137 61/13 79/ / /.518 TP, TPD -13/ DN DN 61/127 72/19 67/16 79/ / /.518 TP, TPD -16/ DN DN 6/132 73/151 7/151 8/ / /.518 TP, TPD -19/ DN DN 69/12 83/171 75/162 9/ / /.518 TP, TPD -23/ DN DN 8/165 8/165 87/181 87/ / /.518 TP, TPD 65-3/ DN 65 DN 65 33/56 37/62 35/59 1/65.56/.1.6/.151 TP, TPD 65-6/ DN 65 DN 65 33/63 36/69 3/66 38/79.56/.1.56/.1 TP, TPD 65-9/ DN 65 DN 65 6/92 57/115 51/19 69/ / /.3912 TP, TPD 65-11/ DN 65 DN 65 63/13 7/155 69/1 8/ / /.58 TP, TPD 65-13/ DN 65 DN 65 65/138 75/158 71/155 82/ / /.58 TP, TPD 65-1/ DN 65 DN 65 7/16 8/177 76/166 91/ / /.518 TP, TPD 65-17/ DN 65 DN 65 81/171 81/171 87/188 88/ / /.518 TP, TPD 65-2/ DN 65 DN 65 8/169 11/21 87/186 18/ / /.518 TP, TPD 8-3/ DN 8 DN 8 37/68 1/72 39/71 /76.56/.1.6/.151 TP, TPD 8-6/ DN 8 DN 8 37/7 /95 39/72 53/1.66/.1.91/.37 TP, TPD 8-7/ DN 8 DN 8 67/11 7/156 8/159 87/ / /.58 TP, TPD 8-9/ DN 8 DN 8 7/18 75/158 83/165 88/ / /

122 Weights and shipping volume TP, TPD, TPE, TPED Pump type Connection Weights Shipping volume [m 3 ] Net [kg] Gross [kg] D1 D D1 S TP/TPD TPE/TPED TP/TPD TPE/TPED TP/TPD TPE/TPED TP, TPD 8-11/ DN 8 DN 8 73/153 8/176 86/17 98/ / /.518 TP, TPD 8-1/ DN 8 DN 8 88/172 87/171 12/192 11/ / /.67 TP, TPD 8-17/ DN 8 DN 8 11/199 16/29 115/218 12/ / /.67 TP, TPD 8-2/ DN 8 DN 8 19/393 18/ /3 2/ / /1.52 TP, TPD 8-27/ DN 8 DN 8 25/15 25/16 229/65 23/ / /1.52 TP, TPD 8-3/ DN 8 DN 8 239/8 233/72 263/53 258/ / /1.52 TP, TPD 1-3/ DN 1 DN 1 1/85 3/93 /9 6/13.1/ /.22 TP, TPD 1-6/ DN 1 DN 1 52/17 63/122 55/113 67/127.1/ /.37 TP, TPD 1-7/ DN 1 DN 1 95/191 1/21 19/28 11/ / /.67 TP, TPD 1-9/ DN 1 DN 1 97/196 19/ /26 133/ / /.67 TP, TPD 1-11/ DN 1 DN 1 17/215 16/ /265 13/26.728/ /.67 TP, TPD 1-13/ DN 1 DN 1 139/282 1/292 16/ /32.728/ /1.52 TP, TPD 1-17/ DN 1 DN 1 168/3 155/ /39 189/36.728/ /1.52 TP, TPD 1-2/ DN 1 DN 1 239/99 2/ 26/59 29/5.9696/ /1.52 TP, TPD 1-2/ DN 1 DN 1 27/ / / / / /1.52 TP, TPD 1-33/ DN 1 DN 1 285/ /61 39/6 31/ / /1.52 TP, TPD 1-37/ DN 1 DN 1 331/681 33/ /732 38/ / /1.8 TP, TPD 1-1/ DN 1 DN 1 36/ / /1.8 TP, TPD / DN 125 DN / /3 213/3 218/ / /1.52 TP, TPD / DN 125 DN / 198/ 22/1 29/7.9696/ /1.52 TP, TPD / DN 125 DN /71 223/72 252/ / / /1.52 TP, TPD / DN 125 DN /6 292/ /65 32/ / /1.52 TP, TPD 125-2/ DN 125 DN /623 31/ /67 36/ / /1.52 TP, TPD / DN 125 DN /717 35/715 12/775 2/ / /1.52 TP, TPD / DN 125 DN /79-28/ /1.8 - TP, TPD 125-2/ DN 125 DN 125 6/ / /1.8 - TP, TPD 1-13/ DN 1 DN 1 285/57 286/ /62 336/ / /1.52 TP, TPD 1-16/ DN 1 DN 1 32/63 31/631 3/693 36/ / /1.52 TP, TPD 1-2/ DN 1 DN 1 33/ /675 38/71 386/ / /1.8 TP, TPD 1-22/ DN 1 DN 1 376/ /753 33/813 25/8.9696/ /1.8 TP, TPD 1-2/ DN 1 DN 1 392/786-9/ /1.8 - TP 1-26/ DN 1 DN 1 385/- 388/- 558/- 561/- 2.3/- 2.3/- TP 1-28/ DN 1 DN 1 11/ / /- - TP 1-3/ DN 1 DN 1 62/ / /- - TP 1-39/ DN 1 DN 1 5/- - 79/ /- - TP 2-18/ DN 2 DN 2 96/ / /- - TP 2-22/ DN 2 DN 2 56/ / /- - TP 2-2/ DN 2 DN 2 625/- - 79/ /- - TP 2-27/ DN 2 DN 2 666/ / /- - TP 2-32/ DN 2 DN 2 817/ / /- - TP 2-33/ DN 2 DN 2 72/ / /- - TP 2-36/ DN 2 DN 2 761/- - 96/ /- - TP 2-/ DN 2 DN 2 911/ / /- - TP 2-1/ DN 2 DN 2 935/ / /- - TP 2-7/ DN 2 DN 2 129/ / /- - TP 2-53/ DN 2 DN / /- -.6/- - TP 2-59/ DN 2 DN / /- -.6/- - TP 2-66/ DN 2 DN 2 188/ /- -.6/- - TP 2-28/ DN 2 DN 3 69/ / /- - TP 2-31/ DN 2 DN 3 82/- - 15/ /- - TP 2-39/ DN 2 DN 3 935/ / /- - The dimension before the slash applies to the single-head pump, and the dimension after the slash applies to the twin-head pump. 122

123 Weights and shipping volume TP, TPD, TPE, TPED TP, TPD, 6-pole, PN 6, 1, 16 Connection Weights Pump type D1 D D1 S Shipping volume [m 3 ] Net [kg] Gross [kg] TP/TPD TPE/TPED TP/TPD TPE/TPED TP/TPD TPE/TPED TP, TPD 125-6/6 DN 125 DN /31-187/ / TP, TPD 125-7/6 DN 125 DN / / / TP, TPD 125-9/6 DN 125 DN /69-26/ / TP, TPD /6 DN 125 DN /82-267/ / TP, TPD 125-1/6 DN 125 DN 125 2/96-27/ / TP, TPD /6 DN 125 DN /567-31/ / TP, TPD 1-6/6 DN 1 DN 1 229/61-259/ / TP, TPD 1-7/6 DN 1 DN 1 253/8-283/ / TP, TPD 1-9/6 DN 1 DN 1 259/ / / TP, TPD 1-11/6 DN 1 DN 1 265/53-295/ / The dimension before the slash applies to the single-head pump, and the dimension after the slash applies to the twin-head pump. TP, 2-pole, PN 25 Pump type Connection Weights Shipping volume D1 [m 3 D D1 S Net [kg] Gross [kg] ] TP 1-62/2 DN 1 DN TP 1-7/2 DN 1 DN TP 1-82/2 DN 1 DN TP 1-96/2 DN 1 DN TP 1-1/2 DN 1 DN TP 1-118/2 DN 1 DN TP 1-1/2 DN 1 DN TP 1-153/2 DN 1 DN TP 1-168/2 DN 1 DN TP, -pole, PN 25 Pump type Connection Weights Shipping volume D1 [m 3 D D1 S Net [kg] Gross [kg] ] TP 1-19/ DN 1 DN TP 1-22/ DN 1 DN TP 1-26/ DN 1 DN TP 1-27/ DN 1 DN TP 1-32/ DN 1 DN TP 1-38/ DN 1 DN TP 1-2/ DN 1 DN TP 125-1/ DN 125 DN TP 125-2/ DN 125 DN TP 125-2/ DN 125 DN TP / DN 125 DN TP / DN 125 DN TP / DN 125 DN TP 125-3/ DN 125 DN TP 1-2/ DN 1 DN TP 1-27/ DN 1 DN TP 1-32/ DN 1 DN TP 1-3/ DN 1 DN TP 1-3/ DN 1 DN TP 1-53/ DN 1 DN TP 1-6/ DN 1 DN TP 2-26/ DN 2 DN TP 2-28/ DN 2 DN TP 2-38/ DN 2 DN TP 2-2/ DN 2 DN TP 2-/ DN 2 DN

124 Weights and shipping volume TP, TPD, TPE, TPED Pump type Connection Weights Shipping volume D1 [m 3 D D1 S Net [kg] Gross [kg] ] TP 2-51/ DN 2 DN TP 2-56/ DN 2 DN TP 2-62/ DN 2 DN TP 2-27/ DN 2 DN TP 2-32/ DN 2 DN TP 2-37/ DN 2 DN TP 2-9/ DN 2 DN TP 2-5/ DN 2 DN TP 2-6/ DN 2 DN TP 2-66/ DN 2 DN TP 3-59/ DN 3 DN TP 3-67/ DN 3 DN TP 3-7/ DN 3 DN TP -7/ DN DN TP -51/ DN DN TP -5/ DN DN TP -67/ DN DN TP -72/ DN DN TP -76/ DN DN

125 Accessories TP, TPD, TPE, TPED Unions and valves Cast-iron pumps A union kit consists of two cast-iron union tails, two cast-iron union nuts and two EPDM gaskets. Pump type, union connection Pressure stage TP, TPE 25 R PN 1 TP, TPE 32 R PN 1 Size A valve kit consists of two brass valves, two brass union nuts and two EPDM gaskets. The valve housing is of pressure die-cast brass. Product number Rp 3/ Rp Rp 1 1/ Rp Rp 1 1/ 9922 Pump type, valve connection Pressure stage Size Bronze pumps A union kit consists of two bronze union tails, two brass union nuts and two EPDM gaskets. The valve housing is of pressure die-cast brass. Product number Rp 3/ TP, TPE 25 R PN 1 Rp Rp 1 1/ TP, TPE 32 R PN 1 Rp 1 1/ 5539 Pump type, union connection Pressure stage Size A valve kit consists of two brass valves, two brass union nuts and two EPDM gaskets. The valve housing is of pressure die-cast brass. Product number Rp 3/ TP, TPE 25 R B PN 1 Rp TP, TPE 32 R B PN 1 Rp 1 1/ 9971 Pump type, valve connection Pressure stage Size Product number Rp 3/ TP, TPE 25 R B PN 1 Rp Rp 1 1/ TP, TPE 32 R B PN 1 Rp 1 1/

126 Accessories TP, TPD, TPE, TPED Counter flanges Cast-iron pumps A flange kit consists of two steel flanges, two gaskets of asbestos-free material IT 2, and the requisite number of bolts. Counter flange Pump type Description Rated pressure Pipework connection Product number Threaded 1 bar, EN Rp 1 1/ Threaded Rp 1¼ For welding ø19 ø78 ø1 ø1 TM TP, TPE 32 TPD, TPED 32 For welding 1 bar, EN mm, nominal 5397 Threaded 16 bar, EN Rp 1 1/ For welding 16 bar, EN mm, nominal 5397 Threaded 1 bar, EN Rp 1 1/ Threaded Rp 1½ For welding ø19 ø88 ø11 ø1 TM TP, TPE TPD, TPED For welding 1 bar, EN mm, nominal Threaded 16 bar, EN Rp 1 1/ For welding 16 bar, EN mm, nominal Threaded 1 bar, EN Rp Threaded Rp 2 For welding ø19 ø12 ø125 ø165 TM TP, TPE TPD, TPED For welding 1 bar, EN mm, nominal 5982 Threaded 16 bar, EN Rp For welding 16 bar, EN mm, nominal 5982 Threaded 1 bar, EN Rp 2 1/ Threaded Rp 2½ For welding ø19 ø122 ø15 ø185 TM TP, TPE 65 TPD, TPED 65 For welding 1 bar, EN mm, nominal Threaded 16 bar, EN Rp 2 1/ For welding 16 bar, EN mm, nominal

127 Accessories TP, TPD, TPE, TPED Counter flange Pump type Description Rated pressure Pipework connection Product number Threaded 6 bar, EN Rp Rp 3 ø19 For welding 6 bar, EN mm, nominal Threaded For welding ø138 ø16 ø2 TM TP, TPE 8 TPD, TPED 8 Threaded 1 bar, EN Rp For welding 1 bar, EN mm, nominal Threaded 16 bar, EN Rp For welding 16 bar, EN mm, nominal Threaded 6 bar, EN Rp Rp ø19 For welding 6 bar, EN mm, nominal Threaded For welding ø158 ø18 ø22 TM TP, TPE 1 TPD, TPED 1 Threaded 1 bar, EN Rp For welding 1 bar, EN mm, nominal Threaded 16 bar, EN Rp For welding 16 bar, EN mm, nominal Threaded 1 bar, EN Rp Threaded Rp 5 For welding ø19 ø188 ø21 ø2 TM TP, TPE 125 TPD, TPED 125 For welding 1 bar, EN mm, nominal Threaded 16 bar, EN Rp For welding 16 bar, EN mm, nominal For welding ø23 ø212 ø2 ø285 TM TP, TPE 1 TPD, TPED 1 For welding 1 bar, EN For welding 16 bar, EN mm, nominal 1 mm, nominal S11116 S

128 Accessories TP, TPD, TPE, TPED Bronze pumps A flange kit consists of two bronze flanges, two gaskets of asbestos-free material IT 2, and the requisite number of bolts. Counter flange Pump type Description Rated pressure Pipework connection Product number Threaded 1 bar, EN Rp 1 1/ Rp 1¼ ø19 TP, TPE 32 B For welding 1 bar, EN mm, nominal Threaded For welding ø78 ø1 ø1 TM Threaded 16 bar, EN Rp 1 1/ For welding 16 bar, EN mm, nominal Threaded 1 bar, EN Rp 1 1/ Threaded Rp 1½ For welding ø19 ø88 ø11 ø1 TM TP, TPE B For welding 1 bar, EN mm, nominal Threaded 16 bar, EN Rp 1 1/ For welding 16 bar, EN mm, nominal Rp 2 ø19 Threaded 1 bar, EN Rp Threaded For welding ø12 ø125 ø165 TM TP, TPE B For welding 1 bar, EN mm, nominal Rp 2½ ø19 Threaded 1 bar, EN Rp 2 1/ Threaded For welding ø122 ø15 ø185 TM TP, TPE 65 B For welding 1 bar, EN mm, nominal Threaded 6 bar, EN Rp Rp 3 Threaded For welding ø19 ø138 ø16 ø2 TM TP, TPE 8 B For welding 6 bar, EN mm, nominal Threaded 1 bar, EN Rp For welding 1 bar, EN mm, nominal Rp ø19 Threaded 6 bar, EN Rp Threaded For welding ø158 ø18 ø22 TM TP, TPE 1 B Threaded 1 bar, EN Rp

129 Accessories TP, TPD, TPE, TPED Base plates Note: Base plates are supplied as standard with TP, TPD, TPE, TPED pumps with 11 kw motors and above. TP, TPE Series 1 and 2 Pump type TP, TPE 32 TP, TPE TP, TPE TP 65-6/2 TP, TPE 65-12/2 TP 65-18/2 TP 65-3/ TP, TPE 65-6/ TP, TPE 8 TP, TPE 1 Hexagon head screws Product number 2 x M12 x 2 mm x M16 x 3 mm TP, TPE Series 3 Pump type TP, TPE 8-2/ TP, TPE 8-27/ TP, TPE 8-3/ TP, TPE 1-2/2 TP, TPE 1-31/2 TP, TPE 1-36/2 TP, TPE 1-39/2 TP, TPE 1-8/2 TP, TPE 1-xx/ TP, TPE 125-xx/ TP, TPE 1-xx/ TP, TPE 125-xx/6 TP, TPE 1-xx/6 Drawing Hexagon head screws Product number 2 x M16 x 3 mm Product number Except TPE Drawing Product number xø18 35 xø TP, TPE Series 3 Pump type 12 2 TP, TPE 32 TP, TPE TP, TPE TP, TPE 65 TP, TPE 8-xx/2 TP, TPE 8-7/ TP, TPE 8-9/ TP, TPE 8-11/ TP, TPE 8-1/ TP, TPE 8-17/ TP, TPE 1-16/2 TP, TPE 1-2/2 TP, TPE 1-2/2 2xø1 2xø1 16 2xø18 xø1 Hexagon head screws TM Product number 2 x M16 x 3 mm TPD, TPED Series 3 Pump type TPD, TPED 32 TPD, TPED TPD, TPED TPD, TPED 65 TPD, TPED 8-xx/2 TPD, TPED 8-7/ TPD, TPED 8-9/ TPD, TPED 8-11/ TPD, TPED 8-1/ TPD, TPED 8-17/ TPD, TPED 1-16/2 TPD, TPED 1-2/2 TPD, TPED 1-2/2 Drawing xø18 TM Hexagon head screws Product number x M16 x 3 mm Product number Drawing Product number xø xø xø18 1 xø1 TM xø1 TM

130 Accessories TP, TPD, TPE, TPED TPD, TPED Series 3 Pump type TPD, TPED 1-2/2 TPD, TPED 1-31/2 TPD, TPED 1-36/2 TPD, TPED 1-39/2 TPD, TPED 1-7/ TPD, TPED 1-9/ TPD, TPED 1-11/ TPD, TPED 1-13/ TPD, TPED 1-17/ Hexagon head screws Product number x M16 x 3 mm Drawing Product number 23 2xø xø1 TM TPD, TPED Series 3 Pump type TPD, TPED 8-2/ TPD, TPED 8-27/ TPD, TPED 8-3/ TPD, TPED 1-2/ TPD, TPED 1-2/ TPD, TPED 1-33/ TPD, TPED 1-37/ TPD, TPED 1-1/ TPD, TPED 125-xx/ TPD, TPED 1-xx/ Hexagon head screws Product number x M16 x 3 mm Drawing Product number xø xø1 TM

131 Accessories TP, TPD, TPE, TPED Blanking flanges Normally used with twin-head pumps. TM TPD, TPED, 2-pole Pump type TPD, TPED 32-6/2 TPD, TPED 32-12/2 TPD, TPED 32-1/2 TPD, TPED 32-18/2 TPD, TPED 32-23/2 TPD, TPED 32-2/2 TPD, TPED 32-2/2 TPD, TPED 32-32/2 TPD, TPED 32-38/2 TPD, TPED 32-6/2 TPD, TPED 32-58/2 TPD, TPED -6/2 TPD, TPED -12/2 TPD, TPED -19/2 TPD, TPED -23/2 TPD, TPED -27/2 TPD, TPED -2/2 TPD, TPED -3/2 TPD, TPED -36/2 TPD, TPED -7/2 TPD, TPED -58/2 TPD, TPED -6/2 TPD, TPED -12/2 TPD, TPED -18/2 TPD, TPED -16/2 TPD, TPED -19/2 TPD, TPED -2/2 TPD, TPED -29/2 TPD, TPED -36/2 TPD, TPED -3/2 TPD, TPED -/2 TPD, TPED -57/2 TPD, TPED -71/2 TPD, TPED -83/2 TPD, TPED -9/2 131

132 Accessories TP, TPD, TPE, TPED Pump type TPD, TPED 65-6/2 TPD, TPED 65-12/2 TP, TPD 65-18/2 TPD, TPED 65-19/2 TPD, TPED 65-23/2 TPD, TPED 65-26/2 TPD, TPED 65-3/2 TPD, TPED 65-1/2 TPD, TPED 65-3/2 TPD, TPED 65-1/2 TPD, TPED 65-6/2 TPD, TPED 65-5/2 TPD, TPED 65-66/2 TPD, TPED 65-72/2 TPD 65-93/2 TPD, TPED 8-12/2 TPD, TPED 8-1/2 TPD, TPED 8-18/2 TPD, TPED 8-21/2 TPD, TPED 8-2/2 TPD, TPED 8-2/2 TPD, TPED 8-33/2 TPD, TPED 8-/2 TPD, TPED 8-52/2 TPD, TPED 8-57/2 TP, TPD 8-7/2 TPD, TPED 1-12/2 TPD, TPED 1-16/2 TPD, TPED 1-2/2 TPD, TPED 1-2/2 TPD, TPED 1-2/2 TPD, TPED 1-31/2 TPD, TPED 1-36/2 TPD, TPED 1-39/2 TP, TPD 1-8/2 132

133 Accessories TP, TPD, TPE, TPED TPD, TPED, -pole Pump type TPD, TPED 32-3/ TPD, TPED 32-/ TPD, TPED 32-6/ TPD, TPED 32-8/ TPD, TPED 32-1/ TPD, TPED 32-12/ TPD, TPED -3/ TPD, TPED -9/ TPD, TPED -1/ TPD, TPED -13/ TPD, TPED -16/ TPD, TPED -3/ TPD, TPED -6/ TPD, TPED -9/ TPD, TPED -11/ TPD, TPED -13/ TPD, TPED -16/ TPD, TPED -19/ TPD, TPED -23/ TPD, TPED 65-3/ TPD, TPED 65-6/ TPD, TPED 65-9/ TPD, TPED 65-11/ TPD, TPED 65-13/ TPD, TPED 65-1/ TPD, TPED 65-17/ TPD, TPED 65-2/ TPD, TPED 8-3/ TPD, TPED 8-6/ TPD, TPED 8-7/ TPD, TPED 8-9/ TPD, TPED 8-11/ TPD, TPED 8-1/ TPD, TPED 8-17/ TPD, TPED 8-2/ TPD, TPED 8-27/ TPD, TPED 8-3/ TPD, TPED 1-3/ TPD, TPED 1-6/ TPD, TPED 1-7/ TPD, TPED 1-9/ TPD, TPED 1-11/ TPD, TPED 1-13/ TPD, TPED 1-17/ TPD, TPED 1-2/ TPD, TPED 1-2/ TPD, TPED 1-33/ TPD, TPED 1-37/ TPD, TPED 1-1/ TPD, TPED / TPD, TPED / TPD, TPED / TPD, TPED / TPD, TPED 125-2/ TPD, TPED / TPD, TPED / TPD 125-2/ 133

134 Accessories TP, TPD, TPE, TPED Pump type TPD, TPED 1-13/ TPD, TPED 1-16/ TPD, TPED 1-2/ TPD, TPED 1-22/ TPD, TPED 1-2/ TPD, 6-pole Pump type TP, TPD 125-6/6 TP, TPD 125-7/6 TP, TPD 125-9/6 TP, TPD /6 TP, TPD 125-1/6 TP, TPD /6 TP, TPD 1-6/6 TP, TPD 1-7/6 TP, TPD 1-9/6 TPD 1-11/6 13

135 Accessories TP, TPD, TPE, TPED Insulating kits Insulating kits are only available for TP, TPE Series 2 pumps. An insulating kit consists of two or three insulating covers made of expanded polypropylene (EPP). The insulating kit is tailored to the individual pump model and has an insulating thickness corresponding to the nominal diameter of the pump. The thermal conductivity of EPP is very low (. W/m C), i.e. the insulating property is very good. The insulating kit encloses the entire pump housing. Fig. 1 Insulating kit TM Product numbers of insulating kits Single-head TP, TPE Series 2 pumps Pump type Product number TP, TPE 32-3/ TP, TPE 32-/ TP, TPE 32-6/ TP, TPE 32-6/ TP, TPE 32-12/ TP, TPE 32-1/ TP, TPE 32-18/ TP, TPE 32-23/ TP, TPE -3/ TP, TPE -6/ TP, TPE -6/ TP, TPE -9/ TP, TPE -12/ TP, TPE -18/ TP, TPE -19/ TP, TPE -23/ TP, TPE -27/ TP, TPE -3/ TP, TPE -6/ TP, TPE -6/ TP, TPE -12/ TP, TPE -18/ TP, TPE 65-3/ TP, TPE 65-6/ TP, TPE 65-6/ TP, TPE 65-12/ TP, TPE 65-18/ TP, TPE 8-3/ TP, TPE 8-6/ TP, TPE 8-12/ TP, TPE 1-3/ TP, TPE 1-6/

136 Accessories TP, TPD, TPE, TPED Sensors Accessory Type Supplier Measuring range Product number Flowmeter Flowmeter Flowmeter Note: All sensors have -2 ma output signal. Sensors for boosting applications Sensors for circulation applications SITRANS F M MAGFLO MAG 31/ W SITRANS F M MAGFLO MAG 31/ W SITRANS F M MAGFLO MAG 31/ W Siemens 1-5 m 3 /h (DN 25) ID8285 Siemens 3-1 m 3 /h (DN ) ID8286 Siemens 6-3 m 3 /h (DN 65) ID8287 Flowmeter SITRANS F M MAGFLO MAG 31/ W Siemens 2-75 m 3 /h (DN 1) ID8288 Temperature sensor TTA () 25 Carlo Gavazzi C to +25 C Temperature sensor TTA (-25) 25 Carlo Gavazzi -25 C to +25 C Temperature sensor TTA () 1 Carlo Gavazzi C to +1 C Temperature sensor TTA () 1 Carlo Gavazzi C to +1 C Accessory for temperature sensor. All with 1/2 RG connection. Protecting tube 9 x mm Carlo Gavazzi Protecting tube 9 x 1 mm Carlo Gavazzi Cutting ring bush Carlo Gavazzi Temperature sensor, ambient temperature WR 52 tmg (DK: Plesner) - C to + C ID8295 Differential temperature sensor ETSD Honsberg C to +2 C Differential temperature sensor ETSD Honsberg C to + C Danfoss pressure sensor kit Pressure range Product number Connection: G 1/2 A (DIN B6kt) Electrical connection: plug (DIN 36) Pressure sensor, type MBS 3, with 2 m screened cable Connection: G 1/ A (DIN B6kt) 5 cable clips (black) Fitting instructions PT (212) bar bar bar bar bar bar bar bar bar bar 5163 Grundfos differential pressure sensor, DPI Pressure range Product number 1 sensor incl..9 m screened cable (7/16" connections) 1 original DPI bracket (for wall mounting) 1 Grundfos bracket (for mounting on motor) 2 M screws for mounting of sensor on bracket 1 M6 screw (self-cutting) for mounting on MGE 9/1 1 M8 screw (self-cutting) for mounting on MGE 112/132 1 M1 screw (self-cutting) for mounting on MGE 16 1 M12 screw (self-cutting) for mounting on MGE 18 3 capillary tubes (short/long) 2 fittings (1/" - 7/16") 5 cable clips (black) Installation and operating instructions Service kit instruction Fitting kit for TPED with two sensors -.6 bar bar bar bar bar bar bar Select the differential pressure sensor so that the maximum pressure of the sensor is higher than the maximum differential pressure of the pump. 136

137 Accessories TP, TPD, TPE, TPED Potentiometer Potentiometer for setpoint setting and start/stop of the pump. CIU communication interface units Product External potentiometer with cabinet for wall mounting. Product number R1 The R1 is used for wireless communication. Communication takes place by means of infrared light. Product Product number R Fig. 2 Grundfos CIU communication interface unit The CIU units enable communication of operating data, such as measured values and setpoints, between TPE pumps and a building management system. The CIU unit incorporates a 2-2 V/VDC power supply module and a CIM module. It can either be mounted on a DIN rail or on a wall. We offer the following CIU units: GrA 6118 CIU 1 For communication via LON. CIU 1 For communication via Profibus DP. CIU 2 For communication via Modbus RTU. CIU 2 For wireless communication via GSM/GPRS. CIU 3 For communication via Bnet MS/TP. Description Fieldbus protocol Product number CIU 1 LON CIU 1 Profibus DP CIU 2 Modbus RTU CIU 2 GSM/GPRS CIU 3 Bnet MS/TP Contact Grundfos For further information about data communication via CIU units and fieldbus protocols, see the CIU documentation available in WebCAPS. 137

138 Accessories TP, TPD, TPE, TPED CIM communication interface modules EMC filter EMC (electromagnetic compatibility to EN 618-3) Fig. 3 Grundfos CIM communication interface module The CIM modules enable communication of operating data, such as measured values and setpoints, between TPE pumps of kw and a building management system. The CIM modules are add-on communication modules which are fitted in the terminal box of TPE pumps of kw. Note: CIM modules must be fitted by authorised personnel. We offer the following CIM modules: CIM 1 For communication via LON. CIM 1 For communication via Profibus DP. GrA6121 Motor 2-pole -pole Emission/immunity Emission: Motors may be installed in residential areas (first environment), unrestricted distribution, corresponding to CISPR11, group 1, class B. Immunity: Motors fulfil the requirements for both the first and second environment. Emission: The motors are category C3, corresponding to CISPR11, group 2, class A, and may be installed in industrial areas (second environment). If fitted with an external Grundfos EMC filter, the motors are category C2, corresponding to CISPR11, group 1, class A, and may be installed in residential areas (first environment). TM CIM 2 For communication via Modbus RTU. CIM 2 For wireless communication via GSM/GPRS. CIM 3 For communication via Bnet MS/TP. Fig. EMC filter The EMC filter for residential areas is available as a complete kit ready for installation. Product Product number EMC filter (TPE 5.5 kw and 7.5 kw, -pole) 9617 EMC filter (TPE kw) Description Fieldbus protocol Product number CIM 1 LON CIM 1 Profibus DP CIM 2 Modbus RTU CIM 2 GSM/GPRS CIM 3 Bnet MS/TP Contact Grundfos For further information about data communication via CIM modules and fieldbus protocols, see the CIM documentation available in WebCAPS. 138

139 Minimum inlet pressure - NPSH TP, TPD, TPE, TPED To ensure optimum and noiseless operation, we recommend the minimum inlet pressure values shown on pages 1 to 12. A minimum inlet pressure is required to avoid pressure drop that may cause cavitation. The minimum inlet pressure (p s ) in bar relative (pressure gauge value on the pump suction side) can be calculated using the following formula. Note: Calculation of the minimum inlet pressure should be based on the maximum required flow. 1 p ( NPSH + H ) ρ g -- ρ c 2 S R S 2.1 p + p [ bar relative] b d p s = Minimum inlet pressure in bar. NPSH R = The required Net Positive Suction Head in metres head. (To be read from the NPSH curve at the highest flow the pump will be delivering). H s = Safety margin = minimum.5 metres head. Note: A safety margin of.5 metres prevents pressure drop. ρ = Density of the pumped liquid measured in kg/m 3. g = Gravitational acceleration measured in m/s. For estimated calculations use the value 9.81 m/s 2. c = Flow velocity of the pumped liquid at the pressure gauge. Insert the flow velocity as the unit [m/s]. (See individual curve charts from page 9). p b = Barometric pressure in bar. (Set the barometric pressure to.97 bar.) Note: Only occasionally the pressure is as high as 1 bar; this value is also at sea level. p d = Vapour pressure in bar. See fig. 5. c Ps NPSH Fig. 5 Minimum inlet pressure Temp. [ C] P d [bar] TM TM

140 Minimum inlet pressure - NPSH TP, TPD, TPE, TPED TP, TPD, 2-pole, PN 6, 1, 16 Pump type p [bar] 2 C 6 C 9 C 11 C 12 C 1 C TP 25-/2 R TP 25-9/2 R TP 32-/2 R TP 32-9/2 R TP, TPD 32-6/ TP, TPD 32-12/ TP, TPD 32-1/ TP, TPD 32-18/ TP, TPD 32-23/ TP, TPD 32-2/ TP, TPD 32-2/ TP, TPD 32-32/ TP, TPD 32-38/ TP, TPD 32-6/ TP, TPD 32-58/ TP -/ TP, TPD -6/ TP -9/ TP, TPD -12/ TP -18/ TP, TPD -19/ TP, TPD -23/ TP, TPD -27/ TP, TPD -2/ TP, TPD -3/ TP, TPD -36/ TP, TPD -7/ TP, TPD -58/ TP, TPD -6/ TP, TPD -12/ TP, TPD -18/ TP, TPD -16/ TP, TPD -19/ TP, TPD -2/ TP, TPD -29/ TP, TPD -36/ TP, TPD -3/ TP, TPD -/ TP, TPD -57/ TP, TPD -71/ TP, TPD -83/ TP, TPD -9/ TP, TPD 65-6/ TP, TPD 65-12/ TP, TPD 65-18/ TP, TPD 65-19/ TP, TPD 65-23/ TP, TPD 65-26/ TP, TPD 65-3/ TP, TPD 65-1/ TP, TPD 65-6/ TP, TPD 65-5/ TP, TPD 65-66/ TP, TPD 65-72/ TP, TPD 65-93/ Pump type p [bar] 2 C 6 C 9 C 11 C 12 C 1 C TP, TPD 8-12/ TP, TPD 8-1/ TP, TPD 8-18/ TP, TPD 8-21/ TP, TPD 8-2/ TP, TPD 8-2/ TP, TPD 8-33/ TP, TPD 8-/ TP, TPD 8-52/ TP, TPD 8-57/ TP, TPD 8-7/ TP, TPD 1-12/ TP, TPD 1-16/ TP, TPD 1-2/ TP, TPD 1-2/ TP, TPD 1-2/ TP, TPD 1-31/ TP, TPD 1-36/ TP, TPD 1-39/ TP, TPD 1-8/

141 Minimum inlet pressure - NPSH TP, TPD, TPE, TPED TP, TPD, -pole, PN 6, 1, 16 Pump type p [bar] 2 C 6 C 9 C 11 C 12 C 1 C TP, TPD 32-3/ TP, TPD 32-/ TP, TPD 32-6/ TP, TPD 32-8/ TP, TPD 32-1/ TP, TPD 32-12/ TP, TPD -3/ TP -6/ TP, TPD -9/ TP, TPD -1/ TP, TPD -13/ TP, TPD -16/ TP, TPD -3/ TP, TPD -6/ TP, TPD -9/ TP, TPD -11/ TP, TPD -13/ TP, TPD -16/ TP, TPD -19/ TP, TPD -23/ TP, TPD 65-3/ TP, TPD 65-6/ TP, TPD 65-9/ TP, TPD 65-11/ TP, TPD 65-13/ TP, TPD 65-1/ TP, TPD 65-17/ TP, TPD 65-2/ TP, TPD 8-3/ TP, TPD 8-6/ TP, TPD 8-7/ TP, TPD 8-9/ TP, TPD 8-11/ TP, TPD 8-1/ TP, TPD 8-17/ TP, TPD 8-2/ TP, TPD 8-27/ TP, TPD 8-3/ TP, TPD 1-3/ TP, TPD 1-6/ TP, TPD 1-7/ TP, TPD 1-9/ TP, TPD 1-11/ TP, TPD 1-13/ TP, TPD 1-17/ TP, TPD 1-2/ TP, TPD 1-2/ TP, TPD 1-33/ TP, TPD 1-37/ TP, TPD 1-1/ TP, TPD / TP, TPD / TP, TPD / TP, TPD / TP, TPD 125-2/ TP, TPD / TP, TPD / Pump type p [bar] 2 C 6 C 9 C 11 C 12 C 1 C TP, TPD 125-2/ TP, TPD 1-13/ TP, TPD 1-16/ TP, TPD 1-2/ TP, TPD 1-22/ TP, TPD 1-2/ TP 1-26/ TP 1-28/ TP 1-3/ TP 1-39/ TP 2-18/ TP 2-22/ TP 2-2/ TP 2-27/ TP 2-32/ TP 2-33/ TP 2-36/ TP 2-/ TP 2-1/ TP 2-7/ TP 2-53/ TP 2-59/ TP 2-66/ TP 2-28/ TP 2-31/ TP 2-39/ TP, TPD, 6-pole, PN 16 Pump type p [bar] 2 C 6 C 9 C 11 C 12 C 1 C TP, TPD 125-6/ TP, TPD 125-7/ TP, TPD 125-9/ TP, TPD / TP, TPD 125-1/ TP, TPD / TP, TPD 1-6/ TP, TPD 1-7/ TP, TPD 1-9/ TP, TPD 1-11/ TP Series, 2-pole, PN 25 Pump type p [bar] 2 C 6 C 9 C 11 C 12 C 1 C TP 1-62/ TP 1-7/ TP 1-82/ TP 1-96/ TP 1-1/ TP 1-118/ TP 1-1/ TP 1-153/ TP 1-168/

142 Minimum inlet pressure - NPSH TP, TPD, TPE, TPED TP Series, -pole, PN 25 Pump type p [bar] 2 C 6 C 9 C 11 C 12 C 1 C TP 1-19/ TP 1-22/ TP 1-26/ TP 1-27/ TP 1-32/ TP 1-38/ TP 1-2/ TP 125-1/ TP 125-2/ TP 125-2/ TP / TP / TP / TP 125-3/ TP 1-2/ TP 1-27/ TP 1-32/ TP 1-3/ TP 1-3/ TP 1-53/ TP 1-6/ TP 2-27/ TP 2-28/ TP 2-38/ TP 2-2/ TP 2-/ TP 2-51/ TP 2-56/ TP 2-62/ TP 2-27/ TP 2-32/ TP 2-37/ TP 2-9/ TP 2-5/ TP 2-6/ TP 2-66/ TP 3-59/ TP 3-67/ TP 3-7/ TP -7/ TP -51/ TP -5/ TP -67/ TP -72/ TP -76/

143 Further product documentation TP, TPD, TPE, TPED WebCAPS WebCAPS is a Web-based Computer Aided Product Selection program available on WebCAPS contains detailed information on more than 185, Grundfos products in more than 2 languages. In WebCAPS, all information is divided into six sections: Catalogue Literature Service Sizing Replacement C drawings. Catalogue This section is based on fields of application and pump types, and contains technical data curves (QH, Eta, P1,, etc.) which can be adapted to the density and viscosity of the pumped liquid and show the number of pumps in operation product photos dimensional drawings wiring diagrams quotation texts, etc. Literature In this section you can access all the latest documents of a given pump, such as data booklets installation and operating instructions service documentation, such as Service kit catalogue and Service kit instructions quick guides product brochures. Service This section contains an easy-to-use interactive service catalogue. Here you can find and identify service parts of both existing and discontinued Grundfos pumps. Furthermore, this section contains service videos showing you how to replace service parts. 13

144 1 Further product documentation TP, TPD, TPE, TPED Sizing This section is based on different fields of application and installation examples, and gives easy step-by-step instructions in how to select the most suitable and efficient pump for your installation carry out advanced calculations based on energy consumption, payback periods, load profiles, life cycle costs, etc. analyse your selected pump via the built-in life cycle cost tool determine the flow velocity in wastewater applications, etc. Replacement In this section you find a guide to selecting and comparing replacement data of an installed pump in order to replace the pump with a more efficient Grundfos pump. The section contains replacement data of a wide range of pumps produced by other manufacturers than Grundfos. Based on an easy step-by-step guide, you can compare Grundfos pumps with the one you have installed on your site. When you have specified the installed pump, the guide will suggest a number of Grundfos pumps which can improve both comfort and efficiency. C drawings In this section it is possible to download 2-dimensional (2D) and 3-dimensional (3D) C drawings of most Grundfos pumps. These formats are available in WebCAPS: 2-dimensional drawings:.dxf, wireframe drawings.dwg, wireframe drawings. 3-dimensional drawings:.dwg, wireframe drawings (without surfaces).stp, solid drawings (with surfaces).eprt, E-drawings. WinCAPS WinCAPS is a Windows-based Computer Aided Product Selection program containing detailed information on more than 185, Grundfos products in more than 2 languages. The program contains the same features and functions as WebCAPS, but is an ideal solution if no Internet connection is available. WinCAPS is available on CD-ROM and updated once ayear. Fig. 6 WinCAPS CD-ROM Subject to alterations. 1