SOLUTIONS TO THE LAB 1 ASSIGNMENT

Transcription

1 SOLUTIONS TO THE LAB 1 ASSIGNMENT Question 1 Excel produces the following histogram of pull strengths for the 100 resistors: 2 20 Histogram of Pull Strengths (lb) Frequency (c) The histogram is one-peaked, bell-shaped, and approximately symmetric. Given the relatively small spread, there is one observation (between 74 and 7) lying far above the main body of the data. This observation may be considered an outlier. We will verify in Question 2 that indeed, the single observation is an outlier in a formal sense. The tails of the distribution are relatively short. The center of the distribution is at approximately 6 pounds. As the distribution is approximately symmetric, we expect that the values of mean and the median are very similar, and close to 6. If all 100 PST values were overestimated by approximately the same small positive value due to a poorly calibrated measuring device, the shape of the histogram would be approximately the same as the histogram for the overestimated values. However, the center (peak) of the histogram would be shifted to the left by the difference between the overestimated values and the accurate values. The mean and the median would also be shifted by the difference to the left but standard deviation and the interquartile range would not be affected (would be the same as the values obtained for the overestimated PST values. Question 2 The summary statistics for the pull strengths obtained with the Descriptive Statistics tool are displayed below: Summary Statistics Mean Standard Error Median 64.4 Mode 64.3 Standard Deviation Sample Variance

2 Kurtosis Skewness Range 16.3 Minimum 8.2 Maximum 74. Sum Count 100 The Paste Function feature applied to our data returns the following values of the first quartile, the third quartile, and the interquartile range: First Quartile Q 1 = Third Quartile Q 3 = Interquartile range = 3.62 (c) As the distribution of pull strengths is approximately symmetric, the mean and standard deviation are appropriate measures of center and variation. The median and the interquartile range are used for skewed distributions. Question 3 According to the 1.*IQR criterion, an outlier is any data point that lies below Q 1-1.*IQR or above the value Q 3 +1.*IQR. Taking into account the values of the lower and upper quartiles, and the interquartile range obtained in Question 2, an outlier lies below and above There is only one observation that satisfies the condition, the value of the largest observation in the data set. The outlier 74. lies far above the main body of the data. Thus we expect that the mean and the standard deviation of the remaining 99 observations would decrease. We do not expect a significant change in the value of the median. The summary statistics for the data without the outlier are displayed below: Summary Statistics (Outlier Removed) Mean Standard Error Median 64.4 Mode 64.3 Standard Deviation Sample Variance Kurtosis Skewness Range 13.4 Minimum 8.2 Maximum 71.6 Sum Count 99 The table confirms the conclusions we have reached before. 2

3 Question 4 In order to convert all 100 PST measurements to kilograms, it is necessary to multiple each value in the column PST by As a consequence, the new mean and the new median can be also obtained by multiplying the value of the mean and the median for the measurements expressed in pounds by Moreover, given the formula for the standard deviation and the above, the new standard deviation can be obtained from the standard deviation for the original data by multiplying it by Also the interquartile range for the data in kilograms is equal to the interquartile range for data on the original scale of measurement multiplied by The histogram for the data expressed in kilograms will have the same shape as the histogram obtained in Question 1. The peak of the new histogram will be approximately at 6*0.44 = Question In order to answer the question whether the new ozone-friendly cleaning process produces similarly strong or stronger solder-joints, on the average, we look at the summary statistics for the distribution. The mean of the pull strengths obtained is , and it is almost identical to the mean of pull strengths for the old technology (64.8). The small difference is due to sampling variability. Thus the new technology produces solder-joints of similar strength, on the average. Now we compare the variability of the two processes. The standard deviation for the old technology is 2.2 lb. This value is smaller than the value of lb obtained in Question 3 (after excluding the outlier). Given the large sample size that the new standard deviation is based on (99), it is safe to conclude that the new process results in slightly higher variability than the old process. More advanced statistical methods are required to determine whether the difference is statistically significant. The new process can be examined thoroughly to determine whether some sources of extra variation can be eliminated. Question 6 The histogram of electrical resistance for the 100 boards is displayed below: Histogram of Electrical Resistances 2 20 Frequency More The histogram is one-peaked, and skewed to the right. Most of the observations lie between 0 and 1, but there are several observations outside the range. The right tail is longer than the left tail of the distribution. There is one outlier. 3

4 As the distribution is skewed, median and interquartile range are appropriate measures of center and spread, respectively. Question 7 The scatterplot of electrical resistance (RES) versus pull strength (PST) displays the relationship between the two variables. It allows you to assess the type of relationship (linear, nonlinear), direction (positive, negati ve), and its strength. The scatterplot for the data is displayed below: Scatterplot of RES vs. PST Electrical Resistance (in teraohms) Pull Strength (in pounds) There is no clear pattern in the plot. It seems that the points in the plot are randomly scattered. However, it is worthy to notice a substantial difference in the variation of pull strength values for low electrical resistance values relative to that one for the high electrical resistance values. There are no obvious outliers in the plot. 4

5 LAB 1 ASSIGNMENT MARKING SCHEMA Proper Header and appearance: 10 points 1. Correctly formatted histogram: 6 points. Analysis of the shape of the histogram: 3 points Center (estimates of the mean and the median): 2 points (c) Histogram of accurate measurements: 2 points Mean, Median, standard deviation and IQR of accurate values: 2 points 2. Summary Statistics: Descriptive Statistics output (mean, median, standard deviation, IQR): 4 points First Quartile, Third Quartile, IQR: 3 points (c) Discussion of appropriateness: 2 points 3. Determining the lower and upper range for outliers: 2 points Identifying the outlier: 2 points Effect of removing the outlier on some summary statistics: 3 points 4. Effect of expressing the PST values in kilograms on summaries: 2 points Effect of expressing the PST values in kilograms on histogram: 2 points. Comparing the average strength of resistors: 2 points Comparing the variability of the two processes: 2 points 6. Correctly formatted histogram: 6 points. Analysis of the shape of the histogram: 3 points Numerical measures to describe typical resistance and the spread: 2 points 7. Relationship between pull strengths and resistance Discussion of the pattern in the scatterplot: 3 points Outliers: 1 point Correctly formatted scatterplot: 6 points TOTAL = 70