Vendor Name: Aspen Equipment Co Contact Person: Mark Lundeen Street Address: 9150 Pillsbury Ave. South P.O. Box: City, State, Zip: Bloomington, MN 55420 Phone #: 952-888-2525 Toll Free #: 800-888-7671 Fax #: 952-656-7159 Email Address: mlundeen@aspeneq.com Website: www.aspenequipment.com PRICE SCHEDULE 4.0 Wing Plow VENDOR PROVIDED INFORMATION Wing Plow - Make and Model Where mounted on truck Moldboard description Moldboard cutting edge description Lift height Hydraulic cylinder description Installation Warranty (months/years) Henderson Model HWS - 8' Patrol Wing Right hand front 32 high straight plow design, 8 cutting edge, 10 gauge grade 50, Rolled moldboard with (6), ½ supporting ribs, Triangular gussets on bottom angle (n/a on trip edge option), Non tripping moldboard with lower brace spring shock, Front moldbaord heel lift. ½ x 6 steel cutting edge, AASTHO 18" benching height, 18" nose 4" Nitrate coated, double acting, toe and heel lift 1 year TOTAL PRICE: $6,170.00 4.1 - Installation cost of Wing Plow PRICE $3,165.00 (I) = Installed & (C) = Carryout 4.1 - (I) Installation as mid mount, behind cab, $3,201.00 4.1 - (I) Installation as rear mount, in front of rear tires $3,019.00 4.2 - (I) *** (PT# 121137 & 121138) 35" x 19" Cheek Plates & Cross tubes mounting kit $875.00 4.3 - (I) Additional charge for wing installation when used w/underbody plow $219.00 4.4 - (I) Power slide for front post, requires DA hydraulic valve (Call for application) $924.00 4.5 - (I) Dual selector valve for power slide $207.00 4.6 - (I) Solenoid operated selector valve for power slide $213.00 4.7 - (I) Carbide cutting edge per foot $82.00 4.8 - (I) Curb guard each $110.00 4.9 - (I) Moldboard wear shoe $126.00 4.10 - (I) Mailbox cut on moldboard "No Flare" (HWS Wings Only) $97.00 4.11 - (I) Nitrogen charged rear push beam (Single Axle) $2,246.00 4.12 - (I) Nitrogen charged rear push beam (Tandem Axle or Front Mount) $2,246.00 4.13 - (I) Manifold quick connect 2 port includes installation $731.00 4.14 - (I) Manifold quick connect 4 port includes installation $1,076.00 4.15 - (I) Manifold quick connect 6 port includes installation $1,167.00 4.16 - (I) Orange side marker $38.00 4.17 - (I) Decel cushion cylinder in lieu of standard $116.00 4.18 - (I) Moldboard punched to accept both carbide & mild cutting edges $0.00 4.19 - (I) Removable rear wing support faceplate (below the frame mount) $794.00 4.20 - (I) Flat face couplers in lieu of standard (2 sets) $157.00 4.21 - (I) FS "Falls" Style Pipe and Bracket wing support ILO Std $644.00 4.22 - (I) Moldboard Boxed-in top flange ILO J-formed (HWS Patrol Wing) $26.00 4.24 - (I) 8" lift front mast ILO STD 18" lift (HWS Patrol Wing, STD mast model) -$179.00 4.25 - (I) 30" lift front mast ILO STD 18" list (HWS Patrol Wing, requires Full trip upgrade) $225.00 4.26 - (I) 48" lift front mast ILO STD 18" list (HWS Patrol Wing, requires Full trip upgrade) $366.00 4.27 - (I) 12" lift front mast ILO STD 18" lift (HWS Patrol Wing, STD mast model) -$106.00 4.28 - (I) 10ga 201 Stainless steel moldboard in lieu of steel 12' $582.00
4.29 - (I) 1 trip brace, 1 shock brace ILO STD Full trip braces (HWS Patrol Full trip) $641.00 4.30 - (I) Above frame rear support (HWS patrol wing) Not for use on rear mount wing) $239.00 4.31 - (I) Non-tripping moldboard with spring on lower wing brace (SD wing) $175.00 4.32 - (I) Full moldboard trip w/ top ext. spring, bottom compression spring (SW wing) $1,360.00 4.40 - (I) 9 steel moldboard in lieu of 8 $166.00 4.41 - (I) 10 steel moldboard in lieu of 8 $337.00 4.42 - (I) 11 steel moldboard in lieu of 8 $467.00 4.43 - (I) 12 steel moldboard in lieu of 8 $655.00 4.44 - (I) 10ga 201 Stainless steel moldboard in lieu of steel 8' $582.00 4.45 - (I) 10ga 201 Stainless steel moldboard in lieu of steel 9' $582.00 4.46 - (I) 10ga 201 Stainless steel moldboard in lieu of steel 10' $582.00 4.47 - (I) 10ga 201 Stainless steel moldboard in lieu of steel 11' $582.00 4.48 - (I) 8'- 12' 3/16 moldboard in lieu of 10 gauge $207.00 4.49 - (I) Adjustable trip cutting edge $1,211.00 4.50 - (I) Full moldboard trip (includes two telescoping push arms)(brace heel lift design) $1,155.00 4.51 - (I) Hydraulic push arm for extendable cutting path (brace heel lift design) $1,615.00 EXTENDED WARRANTY OPTIONS Use this section to offer performance/warranty options, number these items starting with 9.1, 9.2, 9.3, etc. (Specify years, miles or hours extended term covers.) $ - NA DELIVERY CHARGES - SEE SPECIAL TERMS AND CONDITIONS NO FLAT RATE ALLOWED Bloomington, MN 55420 DELIVERY STARTING POINT - City, State, Zip Price per loaded mile $2.50
Vendor Name: Aspen Equipment Co Contact Person: Mark Lundeen Street Address: 9150 Pillsbury Ave. South P.O. Box: City, State, Zip: Bloomington, MN 55420 Phone #: 952-888-2525 Toll Free #: 800-888-7671 Fax #: 952-656-7159 Email Address: mlundeen@aspeneq.com Website: www.aspenequipment.com PRICE SCHEDULE 4.0 Wing Plow VENDOR PROVIDED INFORMATION Wing Plow - Make and Model Where mounted on truck Moldboard description Moldboard cutting edge description Lift height Hydraulic cylinder description Installation Warranty (months/years) Henderson Model SDLWNG - 10' Leveling Wing Right hand front 29 intake, 38" discharge end height, 10 cutting edge, 7 gauge grade 50, formed moldboard with eight (8), ½ supporting ribs ½ x 6 steel cutting edge, AASTHO 68" benching standard, 86" optional Nitrate coated, double acting, toe and heel lift 1 year TOTAL PRICE: $10,714.00 4.1 - Installation cost of Wing Plow PRICE $3,165.00 (I) = Installed & (C) = Carryout 4.1 - (I) Installation as mid mount, behind cab, $3,201.00 4.1 - (I) Installation as rear mount, in front of rear tires $3,019.00 4.2 - (I) *** (PT# 121137 & 121138) 35" x 19" Cheek Plates & Cross tubes mounting kit $875.00 4.3 - (I) Additional charge for wing installation when used w/underbody plow $219.00 4.4 - (I) Power slide for front post, requires DA hydraulic valve (Call for application) $924.00 4.5 - (I) Dual selector valve for power slide $207.00 4.6 - (I) Solenoid operated selector valve for power slide $213.00 4.7 - (I) Carbide cutting edge per foot $82.00 4.8 - (I) Curb guard each $110.00 4.9 - (I) Moldboard wear shoe $126.00 4.10 - (I) Mailbox cut on moldboard "No Flare" (HWS Wings Only) $97.00 4.11 - (I) Nitrogen charged rear push beam (Single Axle) $2,246.00 4.12 - (I) Nitrogen charged rear push beam (Tandem Axle or Front Mount) $2,246.00 4.13 - (I) Manifold quick connect 2 port includes installation $731.00 4.14 - (I) Manifold quick connect 4 port includes installation $1,076.00 4.15 - (I) Manifold quick connect 6 port includes installation $1,167.00 4.16 - (I) Orange side marker $38.00 4.17 - (I) Decel cushion cylinder in lieu of standard $116.00 4.18 - (I) Moldboard punched to accept both carbide & mild cutting edges $0.00 4.19 - (I) Removable rear wing support faceplate (below the frame mount) $794.00 4.20 - (I) Flat face couplers in lieu of standard (2 sets) $157.00 4.21 - (I) FS "Falls" Style Pipe and Bracket wing support ILO Std $644.00 4.22 - (I) Moldboard Boxed-in top flange ILO J-formed (HWS Patrol Wing) $26.00 4.24 - (I) 8" lift front mast ILO STD 18" lift (HWS Patrol Wing, STD mast model) -$179.00 4.25 - (I) 30" lift front mast ILO STD 18" list (HWS Patrol Wing, requires Full trip upgrade) $225.00 4.26 - (I) 48" lift front mast ILO STD 18" list (HWS Patrol Wing, requires Full trip upgrade) $366.00 4.27 - (I) 12" lift front mast ILO STD 18" lift (HWS Patrol Wing, STD mast model) -$106.00 4.28 - (I) 10ga 201 Stainless steel moldboard in lieu of steel 12' $582.00 4.29 - (I) 1 trip brace, 1 shock brace ILO STD Full trip braces (HWS Patrol Full trip) $641.00 4.30 - (I) Above frame rear support (HWS patrol wing) Not for use on rear mount wing) $239.00
4.31 - (I) Non-tripping moldboard with spring on lower wing brace (SD wing) $175.00 4.32 - (I) Full moldboard trip w/ top ext. spring, bottom compression spring (SW wing) $1,360.00 4.40 - (I) 11 cutting edge, 12' moldboard in lieu of 10 $221.00 4.41 - (I) 12 cutting edge, 13' moldboard in lieu of 10 $419.00 4.42 - (I) 13 cutting edge, 14' moldboard in lieu of 10 $565.00 4.43 - (I) 10' 201 stainless steel moldboard in lieu of steel $749.00 4.44 - (I) 11' 201 stainless steel moldboard in lieu of steel $749.00 4.45 - (I) 12' 201 stainless steel moldboard in lieu of steel $749.00 4.46 - (I) 13' 201 stainless steel moldboard in lieu of steel $749.00 4.47 - (I) Canted rear mast ILO standard straight $163.00 4.48 - (I) Full moldboard trip w/top ext. spring, bottom standard $1,142.00 4.49 - (I) Up to 86" benching height in lieu of standard $910.00 EXTENDED WARRANTY OPTIONS Use this section to offer performance/warranty options, number these items starting with 9.1, 9.2, 9.3, etc. (Specify years, miles or hours extended term covers.) $ - NA DELIVERY CHARGES - SEE SPECIAL TERMS AND CONDITIONS NO FLAT RATE ALLOWED Bloomington, MN 55420 DELIVERY STARTING POINT - City, State, Zip Price per loaded mile $2.50
Vendor Name: Aspen Equipment Co Contact Person: Mark Lundeen Street Address: 9150 Pillsbury Ave. South P.O. Box: City, State, Zip: Bloomington, MN 55420 Phone #: 952-888-2525 Toll Free #: 800-888-7671 Fax #: 952-656-7159 Email Address: mlundeen@aspeneq.com Website: www.aspenequipment.com PRICE SCHEDULE 4.0 Wing Plow VENDOR PROVIDED INFORMATION Wing Plow - Make and Model Henderson Model HWS Mid Mount - 6' Where mounted on truck Moldboard description Moldboard cutting edge description Lift height Hydraulic cylinder description Installation Warranty (months/years) Right side, front post in back of rear of cab 27 high straight plow design, 6 cutting edge, 10 gauge grade 50, Rolled moldboard with three (3), 3/8 supporting ribs ½ x 6 steel cutting edge, AASTHO Standard front Mast is 8" lift Nitrate coated, double acting, toe and heel lift 1 year TOTAL PRICE: $5,634.00 4.1 - Installation cost of Wing Plow PRICE $3,165.00 (I) = Installed & (C) = Carryout 4.1 - (I) Installation as mid mount, behind cab, $3,201.00 4.1 - (I) Installation as rear mount, in front of rear tires $3,019.00 4.2 - (I) *** (PT# 121137 & 121138) 35" x 19" Cheek Plates & Cross tubes mounting kit $875.00 4.3 - (I) Additional charge for wing installation when used w/underbody plow $219.00 4.4 - (I) Power slide for front post, requires DA hydraulic valve (Call for application) $924.00 4.5 - (I) Dual selector valve for power slide $207.00 4.6 - (I) Solenoid operated selector valve for power slide $213.00 4.7 - (I) Carbide cutting edge per foot $82.00 4.8 - (I) Curb guard each $110.00 4.9 - (I) Moldboard wear shoe $126.00 4.10 - (I) Mailbox cut on moldboard "No Flare" (HWS Wings Only) $97.00 4.11 - (I) Nitrogen charged rear push beam (Single Axle) $2,246.00 4.12 - (I) Nitrogen charged rear push beam (Tandem Axle or Front Mount) $2,246.00 4.13 - (I) Manifold quick connect 2 port includes installation $731.00 4.14 - (I) Manifold quick connect 4 port includes installation $1,076.00 4.15 - (I) Manifold quick connect 6 port includes installation $1,167.00 4.16 - (I) Orange side marker $38.00 4.17 - (I) Decel cushion cylinder in lieu of standard $116.00 4.18 - (I) Moldboard punched to accept both carbide & mild cutting edges $0.00 4.19 - (I) Removable rear wing support faceplate (below the frame mount) $794.00 4.20 - (I) Flat face couplers in lieu of standard (2 sets) $157.00 4.21 - (I) FS "Falls" Style Pipe and Bracket wing support ILO Std $644.00 4.22 - (I) Moldboard Boxed-in top flange ILO J-formed (HWS Patrol Wing) $26.00 4.24 - (I) 8" lift front mast ILO STD 18" lift (HWS Patrol Wing, STD mast model) -$179.00 4.25 - (I) 30" lift front mast ILO STD 18" list (HWS Patrol Wing, requires Full trip upgrade) $225.00 4.26 - (I) 48" lift front mast ILO STD 18" list (HWS Patrol Wing, requires Full trip upgrade) $366.00 4.27 - (I) 12" lift front mast ILO STD 18" lift (HWS Patrol Wing, STD mast model) -$106.00 4.28 - (I) 10ga 201 Stainless steel moldboard in lieu of steel 12' $582.00 4.29 - (I) 1 trip brace, 1 shock brace ILO STD Full trip braces (HWS Patrol Full trip) $641.00 4.30 - (I) Above frame rear support (HWS patrol wing) Not for use on rear mount wing) $239.00 4.31 - (I) Non-tripping moldboard with spring on lower wing brace (SD wing) $175.00
4.32 - (I) Full moldboard trip w/ top ext. spring, bottom compression spring (SW wing) $1,360.00 4.40 - (I) 7 moldboard in lieu of 6 $156.00 4.41 - (I) 8 moldboard in lieu of 6 $314.00 4.42 - (I) 6' stainless steel moldboard in lieu of standard steel $582.00 4.43 - (I) 7 stainless steel moldboard in lieu of standard steel $582.00 4.44 - (I) 8 stainless steel moldboard in lieu of standard steel $582.00 EXTENDED WARRANTY OPTIONS Use this section to offer performance/warranty options, number these items starting with 9.1, 9.2, 9.3, etc. (Specify years, miles or hours extended term covers.) $ - NA DELIVERY CHARGES - SEE SPECIAL TERMS AND CONDITIONS NO FLAT RATE ALLOWED Bloomington, MN 55420 DELIVERY STARTING POINT - City, State, Zip Price per loaded mile $2.50
Vendor Name: Aspen Equipment Co Contact Person: Mark Lundeen Street Address: 9150 Pillsbury Ave. South P.O. Box: City, State, Zip: Bloomington, MN 55420 Phone #: 952-888-2525 Toll Free #: 800-888-7671 Fax #: 952-656-7159 Email Address: mlundeen@aspeneq.com Website: www.aspenequipment.com PRICE SCHEDULE 4.0 Wing Plow VENDOR PROVIDED INFORMATION Wing Plow - Make and Model Where mounted on truck Moldboard description Moldboard cutting edge description Lift height Hydraulic cylinder description Installation Warranty (months/years) Henderson Smart Link Rotational Floating Wing Mast Right hand front 32 high straight plow design, 8 cutting edge, 10 gauge grade 50, Rolled moldboard with seven (6), ½ supporting ribs, Brace heel lift design ½ x 6 steel cutting edge, AASTHO N/A Nitrate coated, double acting, toe and heel lift 1 year TOTAL PRICE: $7,446.00 4.1 - Installation cost of Wing Plow PRICE $3,165.00 (I) = Installed & (C) = Carryout 4.1 - (I) Installation as mid mount, behind cab, $3,201.00 4.1 - (I) Installation as rear mount, in front of rear tires $3,019.00 4.2 - (I) *** (PT# 121137 & 121138) 35" x 19" Cheek Plates & Cross tubes mounting kit $875.00 4.3 - (I) Additional charge for wing installation when used w/underbody plow $219.00 4.4 - (I) Power slide for front post, requires DA hydraulic valve (Call for application) $924.00 4.5 - (I) Dual selector valve for power slide $207.00 4.6 - (I) Solenoid operated selector valve for power slide $213.00 4.7 - (I) Carbide cutting edge per foot $82.00 4.8 - (I) Curb guard each $110.00 4.9 - (I) Moldboard wear shoe $126.00 4.10 - (I) Mailbox cut on moldboard "No Flare" (HWS Wings Only) $97.00 4.11 - (I) Nitrogen charged rear push beam (Single Axle) $2,246.00 4.12 - (I) Nitrogen charged rear push beam (Tandem Axle or Front Mount) $2,246.00 4.13 - (I) Manifold quick connect 2 port includes installation $731.00 4.14 - (I) Manifold quick connect 4 port includes installation $1,076.00 4.15 - (I) Manifold quick connect 6 port includes installation $1,167.00 4.16 - (I) Orange side marker $38.00 4.17 - (I) Decel cushion cylinder in lieu of standard $116.00 4.18 - (I) Moldboard punched to accept both carbide & mild cutting edges $0.00 4.19 - (I) Removable rear wing support faceplate (below the frame mount) $794.00 4.20 - (I) Flat face couplers in lieu of standard (2 sets) $157.00 4.21 - (I) FS "Falls" Style Pipe and Bracket wing support ILO Std $644.00 4.22 - (I) Moldboard Boxed-in top flange ILO J-formed (HWS Patrol Wing) $26.00 4.24 - (I) 8" lift front mast ILO STD 18" lift (HWS Patrol Wing, STD mast model) -$179.00 4.25 - (I) 30" lift front mast ILO STD 18" list (HWS Patrol Wing, requires Full trip upgrade) $225.00 4.26 - (I) 48" lift front mast ILO STD 18" list (HWS Patrol Wing, requires Full trip upgrade) $366.00 4.27 - (I) 12" lift front mast ILO STD 18" lift (HWS Patrol Wing, STD mast model) -$106.00 4.28 - (I) 10ga 201 Stainless steel moldboard in lieu of steel 12' $582.00 4.29 - (I) 1 trip brace, 1 shock brace ILO STD Full trip braces (HWS Patrol Full trip) $641.00 4.30 - (I) Above frame rear support (HWS patrol wing) Not for use on rear mount wing) $239.00
4.31 - (I) Non-tripping moldboard with spring on lower wing brace (SD wing) $175.00 4.32 - (I) Full moldboard trip w/ top ext. spring, bottom compression spring (SW wing) $1,360.00 4.40 - (I) Front heel lifting option ILO std rear heel lift -$386.00 4.41 - (I) 9 steel moldboard in lieu of 8 $166.00 4.42 - (I) 10 steel moldboard in lieu of 8 $337.00 4.43 - (I) 11 steel moldboard in lieu of 8 $467.00 4.44 - (I) 12 steel moldboard in lieu of 8 $655.00 4.45 - (I) 10ga Stainless steel moldboard in lieu of steel 8' $582.00 4.46 - (I) 10ga Stainless steel moldboard in lieu of steel 9' $582.00 4.47 - (I) 10ga Stainless steel moldboard in lieu of steel 10' $582.00 4.48 - (I) 10ga Stainless steel moldboard in lieu of steel 11' $582.00 4.49 - (I) 8'- 12' 3/16 moldboard in lieu of 10 gauge $207.00 4.50 - (I) Hydraulic push arm for extendable cutting path (brace heel lift SL only) $681.00 4.51 - (I) Hydraulic push arm for extendable cutting path (for use with Front Heel Lift SL) $1,336.00 EXTENDED WARRANTY OPTIONS Use this section to offer performance/warranty options, number these items starting with 9.1, 9.2, 9.3, etc. (Specify years, miles or hours extended term covers.) $ - NA DELIVERY CHARGES - SEE SPECIAL TERMS AND CONDITIONS NO FLAT RATE ALLOWED Bloomington, MN 55420 DELIVERY STARTING POINT - City, State, Zip Price per loaded mile $2.50