INSTALATION INSTRUCTIONS FOR SPY FANCAN Great care has gone into providing complete and thorough installation instructions. If for some reason you are having trouble with any part of this installation please do not hesitate to give us a call. 1. Ensure that all parts and the proper quantities of parts that are listed in the Parts List on the Assembly Drawing are in the package. 2. Refer to Spyder Shop Manual and remove the Middle Right side body panel. If you have a 10mm Gear Wrench, removal of the Lower Right side body panel is not necessary. If you don t have a 10mm Gear Wrench remove the Lower Right side body panel. 3. Loosen the top inner bolt that holds the radiator fan to the radiator. The picture below shows the bolt has been removed but it only needs to be loosened enough to slip the tab of the FANCAN under the head of the bolt. Page 1
4. Loosen the lower outer bolt that holds the radiator fan to the radiator. The picture below shows the bolt has been removed but it only needs to be loosened enough to slip the tab of the FANCAN under the head of the bolt. Page 2
5. Install FANCAN as shown in the following pictures. NOTE: the FANCAN in these pictures is a prototype. The FANCAN that you have is not exactly the same as this one but the functionallity is still the same. Tighten the bolts that were loosened. Page 3
6. On the back of the Middle Right side body panel there is a scoop that must be removed. There are three metal clips and two screws that must be removed to do this. They have already been removed in the following picture. 7. Reinstall the Lower Right side body panel if it was removed then reinstall the Middle Right side body panel and the installation is complete. If for some reason you are having trouble with any part of this installation please do not hesitate to give us a call at 334 277 2224. Ask for Jeff Kranzusch or Robert Kawzinski. Page 4
PLEASE READ THESE TERMS AND CONDITIONS VERY CAREFULLY. THE TERMS AND CONDITIONS OF PRODUCT SALES AND SERVICE PROJECTS ARE LIMITED TO THOSE CONTAINED HEREIN. ANY ADDITIONAL OR DIFFERENT TERMS OR CONDITIONS IN ANY FORM DELIVERED BY YOU ( CUSTOMER ) ARE HEREBY DEEMED TO BE MATERIAL ALTERATIONS AND NOTICE OF OBJECTION TO THEM AND REJECTION OF THEM IS HEREBY GIVEN. BY ACCEPTING DELIVERY OF THE PRODUCTS OR BY ENGAGING INDUSTRIAL SPECIALTY COMPANY, INC. ON THE INVOICE, STATEMENT OF WORK OR OTHER ISCI DOCUMENTATION ( SELLER ) TO PROVIDE PRODUCT TO PERFORM OR PROCURE ANY SERVICES, CUSTOMER AGREES TO BE BOUND BY AND ACCEPTS THESE TERMS AND CONDITIONS. ISCI (SELLER) MAKES NO CLAIMS OF REDUCED RISK OF INJURY OR INHERENT AGREEMENT ON THE PERFORMANCE AS THE PRODUCT RELATES TO SAFETY. ISCI CANNOT GUARANTEE OPTIMAL PERFORMANCE OF PRODUCT IF NOT INSTALLED BY ISCI, NOR IF PROPER INSTALLATION INSTRUCTIONS PROVIDED BY ISCI ARE NOT ADHERED TO. UNDER NO CIRCUMSTANCES AND NOTWITHSTANDING THE FAILURE OF ESSENTIAL PURPOSE OF ANY REMEDY SET FORTH HEREIN, WILL SELLER, IT S AFFILIATES OR IT S OR THEIR SUPPLIERS, SUBCONTRACTORS OR AGENTS BE LIABLE FOR: (A) ANY INCIDENTAL, INDIRECT, SPECIAL, PUNITIVE OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO, LOSS OF PROFITS, BUSINESS, REVENUES OR SAVINGS, EVEN IF SELLER HAS BEEN ADVISED OF THE POSSIBILITIES OF SUCH DAMAGES, OR IF SUCH DAMAGES ARE OTHERWISE FORESEEABLE, IN EACH CASE, WHETHER A CLAIM FOR ANY SUCH LIABILITY IS PREMISED UPON BREACH OF CONTRACT, WARRANTY, NEGLIGENCE, STRICT LIABILITY OR OTHER THEORY OF LIABILITY; (B) ANY CLAIMS, DEMANDS OR ACTIONS AGAINST CUSTOMER BY ANY THIRD PARTY; (C) ANY LOSS OR CLAIM ARISING OUT OF OR IN CONNECTION WITH CUSTOMER S IMPLEMENTATION OF ANY CONCLUSIONS OR RECOMMENDATIONS BY SELLER OR IT S AFFILIATES BASED ON, RESULTING FROM, ARISING OUT OF OR OTHERWISE RELATED TO THE PRODUCTS OR SERVICES; OR (D) ANY INJURIES DERIVED FROM THE USE OF THIS PRODUCT INDEPENDENTLY DERIVED FROM OR CAUSED BY IMPROPER INSTALLATION OF PRODUCT. THE ABOVE MENTIONED CONDITIONS ARE NOT ALL INCLUSIVE IN RELATION TO THE LIABILITY OF ISCI (SELLER). Page 5
4 3 PARTS LIST REVISION HISTORY ITEM QTY PART NUMBER DESCRIPTION REV DESCRIPTION DATE APPROVED 1 1 349171830_RevC Main Plate A Released for Production 2 1 349171831_RevC Side 3 2 349171832 Angle 4 1 349171833 Mounting Tab 5 1 349171833_LH Mounting Tab_LH D 6 8 90183A311 1/8" Blind Rivet Flat Washer D 7 8 97525A625 1/8" 18-8 SS Blind Rivet 2 C C B B Industrial Specialty Company Inc.'s prior written consent, all rights Model File # Fract. ±1/32" Surface Area Description Company A ISCI A Tolerances Date Material Dimensions Revision Industrial Specialty Co. Inc. Proprietary Property INDUSTRIAL SPECIALTY CO. INC. Unless Noted Otherwise 9/9/2010 This drawing is the proprietary property of Industrial Specialty Precision Machining / Engineered Products / Anodizing Finish Company Inc., and must not be used except in connection with our.xxx.xx.x Drawn By Part # 50 Forest Hills Dr. - P.O. Box 3262 - Montgomery, AL 36109 Inches PH (334) 277-2224 FX (334) 277-5846 work, not in any manner disclosed to any third party without ±.005 ±.01 ±.02 R.L.K. SPY-FS of design and invention are reserved..xx.x x 230.18 in^2 M:\34917-1\SPY-FANCAN (FANCAN)\SPY-FANCAN.iam Scale: NTS Drawing Unit: IN. [mm] Metric ±.13 ±.25 ±.5 Approx. Weight Used in Assembly # Project File # Angle ±0-30' 0.67 lbmass M:\34917-1\SPY-FANCAN (FANCAN)\SPY-FANCAN.idw 4 3 2 1 1