CAPTIVUE SPORTS MESSAGE CENTER INSTRUCTION MANUAL REVISION DATE: 08-21-07 PART#: 98-0019-42
SERVICE & CUSTOMER INFORMATION CUSTOMER MUST HAVE PART NUMBER WHEN ORDERING ITEMS THROUGH THE SERVICE DEPARTMENT. IF FURTHER HELP IS NEEDED CONTACT A TRANS-LUX SERVICE REP IN YOUR TRANS-LUX DEALER ORGANIZATION OR PHONE THE TRANS-LUX HELP DESK AT (800) 462-2716. TO AID YOU IN YOUR DISCUSSIONS WITH SERVICE REPS, WE SUGGEST THAT YOU RECORD THE FOLLOWING: MODEL NUMBER: TRANS-LUX SALES ORDER NUMBER: (THIS NUMBER IS FOUND IN THE UPPER RIGHT HAND CORNER OF THE PACKING SLIP AND INVOICE.) INSTALLATION DATE: WARRANTY: COPIES OF THE FIVE YEAR LIMITED WARRANTY IS ENCLOSED.
Trans-Lux DES MOINES, IOWA INSTRUCTION DRAWING LIST CAPTIVUE SPORTS MESSAGE TABLE OF CONTENTS DESCRIPTION DRAWING NUMBER INTRODUCTION.. 98-0055-01 STRUCTURAL INSTALLATION 01-0212-10 COLUMNS AND FOOTINGS CHART. 98-0029-01 PREFACE ELECTRICAL INSTALLATION.. 97-0019-42 GROUNDING INSTRUCTIONS. 01-0107-01 TROUBLE SHOOTING... 97-0010-01 WARRANTY, MONCHROME MESSAGE WARRANTY, COLOR MESSAGE
INTRODUCTION This manual is a reference guide for the installation and trouble shooting of Fair-Play message center. Read the entire manual prior to beginning installation of your message center. It includes information for typical installation, maintenance and troubleshooting. You should always be mindful of local codes and regulations regarding the installation of electronic display equipment. These instructions may need to be altered for your installation. It is recommended you seek the guidance of a local professional for any installation changes required for your installation. If further help is needed, you may contact your local Fair-Play representative or the Trans-Lux Help Desk at 1-800-462-2716. 98-0055-01,preface.doc, REV. 4/6/2006
Structural Installation The following instructions are to be used as a guide for the selection and installation of your display. Read thoroughly before selecting an installation method. The installation should be altered for different soil conditions, clearances or local codes. Trans-Lux assumes no responsibility for installations done by others. All installations should be reviewed and approved by a licensed professional structural engineer in your area prior to construction. These instructions show typical installations. Actual installation will depend on the equipment purchased and the desired arrangement of the equipment purchased. True dimensions should be verified prior to construction. Water Ingress: No additional penetrations may be created in the product unless they are sealed per Nema 4 Standard. All field penetrations must be tested using a stream of water poured from a container located not less than 6 away horizontally. Warranty will be void if this testing is not completed during installation, or if there is water ingress from field modifications. Any cabinets located above the product must not allow water to build up and then flow through conduits into the product. Penetrations between product and higher cabinets must be sealed between the cabinet internal spaces using water tight cable to conduit seals. Holes remaining from eye bolt removal must be filled, sealed and tested. Ventilation: Install product so that air flow is not restricted. Customer s structure must allow for the free flow of outside ambient air to the product, without recirculation of air. Warranty will be void if components fail due to air flow restrictions. Design criteria The following minimum design criteria shall be used when selecting the columns and footings shown in this manual: 1. Codes Uniform Building Code, 1997 American Concrete Institute 318-95 American Institute of Steel Construction, ASD 1989 2. Lateral Loads Wind: Base Wind Speed 80 mph, Exposure B 3. Concrete Strengths Ultimate strengths at 28 days (per ACI cylinder testing) drilled piers 3000 psi, 145 pcf 4. Structural Steel Material shall be ASTM: A36 Rolled Sections, Fy = 36 ksi A500 Grade B, Structural Tubes, Fy = 46 ksi A53 Grade B, Pipe Fy = 35 ksi 5. Soil average with allowable stresses of 2500 psf. Note: Any deviations from the designs criteria above will be listed on the typical installation drawing in this manual. These deviations apply only to the installation shown in this manual. Local codes may specify additional design requirements. The building authority in your area should be contacted prior to beginning construction. 01-0212-10,structural.doc Rev. 9/13/2006
Erection Use the following steps to determine the structural installation requirements of your display. 1. Determine location: The display may be positioned to face any direction so that the spectators can see it. For maximum visibility, place it so that the sun does not shine directly on the face of the display. 2. Select installation method to match display purchased. The following page shows a typical installation for your display. This installation may need to be modified for your individual needs. 3. Installation notes: The display can easily be lifted into place using a crane or boom truck such as used by utilities and sign companies. U-bolts or eyebolts are included on the top edge of the display. Hook the slings or spreader bar cables into these bolts when lifting the display. The bolts may be removed after the display is secured to the supports. Caution: If bolts are removed, plug open holes in display or water damage will occur and warranty will be void. The display is to be welded or bolted to the supports at each hanger location. While Trans-Lux believes the instructions contained herein are accurate and correct, in light of varying soil and other conditions, Trans-Lux does not warrant the accuracy or correctness of such instructions and there are no warranties, express or implied including but not limited to any warranties of merchantability or fitness for a particular purpose. In no event shall Trans-Lux be liable to dealer or its customer for any indirect, special or consequential damages or lost profits arising out of or related to this sale or the performance or breach thereof even if Trans-Lux has been advised of the possibility thereof. Trans-Lux s liability to dealer, if any, in connection with this sale shall in no event exceed the total amount paid by dealer for the scoreboard and sign equipment furnished by Trans-Lux. 01-0212-10,structural.doc Rev. 9/13/2006
COLUMNS and FOOTINGS HEIGHT TO TOP OF EQUIPMENT 10'-0" GRADE FOOTING DEPTH OPTIONAL EQUIPMENT SCOREBOARD OPTIONAL EQUIPMENT COLUMN SPACING I-BEAM COLUMN Notes: Read thoroughly before selecting columns & footings. Reference chart on back side for columns and footings. The column length equals all component heights + 10-0 (above grade) + footing depth. See item A below if installing a top mounted pendant sign. This chart does not support 2-sided installations. Columns and footings are selected for locating scoreboard & components 10-0 above grade. Wind load: 30psf (80 mph). Soil: average with allowable stresses of 2500 psf. Design should be altered for different soil conditions, clearance, or local codes. If your scoreboard size is not listed check with your local Fair-Play representative or seek the services of a local Engineer. This chart does not support equipment with end signs. Reference your installation Manual for back view hanger details and proper column spacing. FOOTING DIAMETER A When calculating column length, do not include any top mounted Pendant sign models. These signs fasten to the edge of the scoreboard and do not require columns. While Fair-Play believes the instructions contained herein are accurate and correct, in light of varying soil and other conditions, Fair-Play does not warrant the accuracy or correctness of such instructions and there are no warranties, expressed or implied including but not limited to any warranties of merchantability or fitness for a particular purpose. In no event shall Fair-Play be liable to dealer or its customer for any indirect, special or consequential damages or lost profits arising out of or related to this sale or the performance or breach thereof even if Fair-Play has been advised of the possibility thereof. Fair-Play s liability to dealer, if any, in connection with this sale shall in no event exceed the total amount paid by dealer for the scoreboard & sign equipment furnished by Fair-Play.
COLUMNS and FOOTINGS CHART Length of Scoreboard 8' 8'-6" 9' 10' 12' 14' 16' 18' 20' 24' 27' 32' 36' 45' # of Columns 2 2 2 2 2 2 2 2 2 2 2 3 4 5 Spacing 4'-0" 4'-3" 4'-6" 5'-0" 6'-0" 7'-0" 8'-0" 9'-0" 10'-0" 12'-0" 13'-6" 10'-6" 9'-0" 9'-0" Height from grade to top of equipment 13-14 ft W6 X 9 W6 X 9 W6 X 9 W6 X 9 W6 X 9 W8 X 10 W10 X 12 W10 X 12 W8 X 13 W8 X 13 W8 X 15 W8 X 13 W10 X 13 W10 X 13 2'-0" dia 2'-0" dia 2'-0" dia 2'-0" dia 2'-0" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 4'-6" deep 4'-6" deep 4'-6" deep 5'-0" deep 5'-0" deep 5'-0" deep 5'-0" deep 5'-6" deep 5'-6" deep 6'-0" deep 6'-6" deep 6'-0" deep 6'-0" deep 6'-0" deep 15-16 ft W8 X 10 W8 X 10 W10 X 12 W8 X 13 W8 X 13 W10 X 15 W10 X 15 W10 X 17 W10 X 17 W10 X 19 W10 X 19 W8 X 18 W8 X 15 W8 X 15 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 5'-0" deep 5'-0" deep 5'-0" deep 5'-0" deep 5'-6" deep 6'-0" deep 6'-0" deep 6'-6" deep 6'-6" deep 7'-0" deep 7'-6" deep 7'-0" deep 6'-6" deep 6'-6" deep 17-18 ft W8 X 13 W10 X 15 W8 X 15 W12 X 16 W8 X 15 W10 X 17 W12 X 19 W10 X 19 W8 X 21 W10 X 2 W10 X 22 W8 X 21 W10 X 19 W10 X 19 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 5'-6" deep 5'-6" deep 5'-6" deep 6'-0" deep 6'-0" deep 6'-6" deep 7'-0" deep 7'-0" deep 7'-6" deep 8'-0" deep 8'-6" deep 7'-6" deep 7'-0" deep 7'-0" deep 19-20 ft W8 X 15 W10 X 17 W10 X 17 W12 X 19 W10 X 19 W8 X 21 W12 X 22 W10 X 22 W10 X 22 W10 X 30 W10 X 26 W10 X 26 W10 X 22 W10 X 22 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 6'-0" deep 6'-0" deep 6'-0" deep 6'-6" deep 7'-0" deep 7'-6" deep 7'-6" deep 8'-0" deep 8'-6" deep 9'-0" deep 9'-0" deep 8'-6" deep 8'-0" deep 8'-0" deep 21-22 ft W10 X 19 W8 X 18 W10 X 19 W12 X 22 W10 X 22 W10 X 22 W12 X 26 W10 X 30 W10 X 26 W10 X 39 W12 X 30 W12 X 30 W12 X 26 W12 X 26 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 3'-0" dia 2'-6" dia 2'-6" dia 2'-6" dia 3'-0" dia 3'-0" dia 3'-0" dia 3'-0" dia 6'-6" deep 6'-6" deep 6'-6" deep 7'-0" deep 7'-6" deep 8'-0" deep 7'-6" deep 8'-6" deep 9'-0" deep 9'-6" deep 9'-6" deep 8'-6" deep 8'-0" deep 8'-0" deep 23-24 ft W10 X 22 W10 X 22 W10 X 22 W10 X 22 W10 X 26 W14 X 30 W12 X 26 W12 X 30 W12 X 30 W10 X 45 W12 X 35 W12 X 35 W10 X 30 W10 X 30 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 3'-0" dia 3'-0" dia 3'-0" dia 3'-0" dia 2'-6" dia 3'-0" dia 3'-0" dia 2'-6" dia 2'-6" dia 7'-0" deep 7'-0" deep 7'-0" deep 7'-6" deep 8'-0" deep 8'-0" deep 8'-6" deep 8'-6" deep 9'-0" deep 10'-6" deep 10'-0" deep 9'-0" deep 9'-6" deep 9'-6" deep 25-26 ft W10 X 22 W10 X 22 W10 x 26 W10 x 26 W10 x 26 W14 X 34 W12 X 30 W12 X 35 W12 X 35 W12 X 50 W16 X 45 W12 X 40 W12 X 35 W12 X 35 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 2'-6" dia 3'-0" dia 3'-0" dia 3'-0" dia 3'-0" dia 3'-0" dia 3'-6" dia 3'-0" dia 3'-0" dia 3'-0" dia 7'-6" deep 7'-6" deep 7'-6" deep 8'-0" deep 8'-6" deep 8'-6" deep 9'-0" deep 9'-0" deep 9'-6" deep 10'-0" deep 10'-0" deep 10'-0" deep 9'-0" deep 9'-0" deep 27-28 ft W10 X 26 W10 X 26 W10 X 26 W12 X 30 W12 X 30 W14 X 38 W12 X 35 W12 X 40 W12 X 40 W12 X 53 W18 X 50 W14 X 43 W12 X 35 W12 X 35 2'-6" dia 2'-6" dia 2'-6" dia 3'-0" dia 3'-0" dia 3'-0" dia 3'-0" dia 3'-0" dia 3'-0" dia 3'-0" dia 3'-6" dia 3'-0" dia 3'-0" dia 3'-0" dia 8'-0" deep 8'-0" deep 8'-0" deep 8'-0" deep 8'-6" deep 9'-0" deep 9'-6" deep 10'-0" deep 10'-0" deep 11'-0" deep 10'-6" deep 10'-6" deep 10'-0" deep 10'-0"deep 29-30 ft W10 X 30 W10 X 30 W10 X 30 W12 X 35 W12 X 35 W14 X 38 W12 X 40 W12 X 50 W14 X 48 W14 X 53 W18 X 55 W16 X 50 W14 X 43 W14 X 43 2'-6" dia 2'-6" dia 2'-6" dia 3'-0" dia 3'-0" dia 3'-0" dia 3'-0" dia 3'-0" dia 3'-0" dia 3'-6" dia 3'-6" dia 3'-6" dia 3'-0" dia 3'-0" dia 8'-0" deep 8'-6" deep 8'-6" deep 8'-6" deep 9'-0" deep 9'-6" deep 10'-0" deep 10'-6" deep 10'-6" deep 11'-0" deep 11'-6" deep 10'-6" deep 10'-6" deep 10'-6"deep 31-32 ft W12 X 30 W12 X 30 W12 X 35 W14 X 38 W14 X 38 W14 X 43 W12 X 45 W14 X 53 W14 X 48 W14 X 61 W18 X 60 W18 X 55 W14 X 43 W14 X 43 3'-0" dia 3'-0" dia 3'-0" dia 3'-0" dia 3'-0" dia 3'-0" dia 3'-0" dia 3'-6" dia 3'-0" dia 3'-6" dia 3'-6" dia 3'-6" dia 3'-0" dia 3'-0" dia 8'-0" deep 8'-0" deep 8'-6" deep 8'-6" deep 9'-6" deep 10'-0" deep 10'-6" deep 10'-0" deep 11'-0" deep 11'-6" deep 12'-0" deep 11'-0" deep 11'-0" deep 11'-0"deep 33-34 ft W14 X 34 W12 X 35 W12 X 35 W14 X 38 W12 X 45 W14 X 43 W12 X 53 W14 X 53 W14 X 53 W14 X 61 W18 X 65 W18 X 60 W14 X 48 W14 X 48 3'-0" dia 3'-0" dia 3'-0" dia 3'-0" dia 3'-0" dia 3'-0" dia 3'-0" dia 3'-6" dia 3'-6" dia 3'-6" dia 3'-6" dia 3'-6" dia 3'-0" dia 3'-0" dia 8'-6" deep 8'-6" deep 9'-0" deep 9'-0" deep 9'-6" deep 10'-6" deep 11'-0" deep 10'-6" deep 11'-0" deep 12'-0" deep 12'-6" deep 11'-6" deep 11'-0' deep 11'-0' deep 98-0029-01 - Rev. 01-23-07
POWER INSTALLATION The following items must be considered when installing your new display. Any technical questions should be directed towards a qualified technician. Trans-Lux assumes no responsibility for installation done by others. All power connections should follow local codes and the current NEC (National Electric Code). REQUIREMENTS 1. Your marquee requires a 120 VAC single phase: two wire grounded power supply at the marquee. A 120 VAC, 2 wire grounded power supply at the control location. The power connection is typically located in the upper most left end of the display as you are facing it. 2. The total power required, when all LED s or lamps are turned on, is listed on the identification label provided with your sign. Wire size should be determined by a local electrician typically determined by both load and wire lengths. 3. The control cable depends on the type of control you have. a. It should be installed in conduit (1/2 or larger) for mechanical protection. Care should be taken when soldering the cable to the control connectors. b. The receiver typically located in the upper most left end of the display as you are facing it. The control cable not provided attaches to the receiver with the connectors supplied with your display. Connectors will depend on the type of control used. PROLINE CONTROLLERS: Fiber connection made at location J1 of the fiber adapter card connected on the UXC controller located on the left end of the display as you are facing it. 4. The control data cable and power cables must be routed in separate conduit. (Placing low voltage data cables with high voltage power cable will create a safety hazard and/or cause damage to your equipment.) 5. A fused disconnect, usually mounted on the support column within view of the display face. 6. Switch power off to the system when not in use. The control console should be disconnected and placed in a storage closet to protect against theft and/or vandalism. 7. The proper grounding of the electrical circuits and the display structure are important aspects of any installation. Refer to drawing 01-0107-01 for suggestions on grounding circuits. If problems develop after the installation is complete, contact your Trans-Lux representative or the Trans-Lux Service Department. 98-0019-42_Elec Preface.doc 7/11/06
DISPLAY 8 FT MIN. (REF. 250-52) 45-90 NOTE: ALL REFERENCES ARE TO THE NATIONAL ELECTRICAL CODE, 1999 EDITION GROUND LEVEL SUGGEST 1/2'' CONDUIT (REF. 250-64B) FLUSH WITH OR BELOW GROUND LEVEL UNLESS PROTECTED. USE LISTED CLAMP (REF. 250-70) SUGGEST SECURING CONDUIT TO ROD. SOLID OR STRAND CORROSION PROTECTED CONTINUOUS FROM TERMINAL BLOCK (REF. 250-64B) ROD 8 FT. LONG MIN. FREE OF NON-CONDUCTIVE COATINGS. (REF. 250-52) FOR PROPER CONDUCTOR SIZING (REF. 250-66) 01-0107-01 11/05/02 DLS
WARNING: CAUTION MUST BE TAKEN WHEN TROUBLESHOOTING YOUR SIGN, RISK OF ELECTRICAL SHOCK OR ELECTROCUTION POSSIBLE. ONLY QUALIFIED PERSONNEL SHOULD ATTEMPT TROUBLESHOOTING THE SIGN. INJURY OR DEATH MAY OCCUR. Service box Does the service box have power coming into it? If yes, continue on. If no, check other power in the area, contact you local electrician. Does the service box have the same amount of power coming out of it? If yes, continue on. If no, check the following: Is the service box main power switch on? If the service box has fuses, are any fuses burned out? Are all physical connections still firmly in place? Is there any other apparent damage to the service box? If still no, contact you local electrician. Customer power hookup to sign Does the power hookup have power coming into it? If yes, continue on. If no, follow the incoming cable back to the service box to see if it has been cut. Does the power hookup have power coming out of it? If yes, continue on to the receiver. If no, check the following: Are any fuses blown? If yes, check the following: Is there water or corrosion in the power connection? Has the wiring been pinched in the service accesses or elsewhere? Are there animal nest or other non-standard physical connections in the wiring? Is the connection on the output loose? Are all physical connections still firmly in place? If the fuse is not blown, check the following: Are all physical connections still firmly in place? Is there any other apparent damage to the breaker box? Receiver Does the receiver have power coming into it? (The video processor has a single red power indicator LED. If it is on, the receiver has power.) If yes, continue on. If no, follow the incoming cable back to the breaker box to see if it has been cut. Are all physical connections still firmly in place? Are all socketed components oriented correctly? Has any soldering broken loose? Is there any apparent damage to the receiver? If the above steps do not restore power flow through the receiver, call Trans-Lux Customer Support at 1-800-747-5305 or 1-800-462-2716 for further assistance. 97-0010-01,trouble shooting, REV. 8/28/2003
LED panels Does the LED panel have power coming into it? If no, check the following: Does the power supply have power coming out of it? Are there any fuses blown (at the fuse holder)? If no, call Trans-Lux Customer Support at 1-800-747-5305 or 1-800-462-2716 for further assistance. 97-0010-01,trouble shooting, REV. 8/28/2003
Trans-Lux Midwest Corporation d.b.a. Fair-Play Scoreboards ( Seller ) manufactures a variety of solid state electronic products. Seller warrants that for a period of five (5) years from date of invoice of any of its monochrome red or amber Light Emitting Diode (LED) products it will repair or replace, from new or serviceable used parts, at the Seller s option, any of its LED electronic products that are found to be defective in materials and/or workmanship under normal use and maintenance. This warranty requires that the defective equipment be returned to Seller. A return authorization number must be obtained from the Seller s Service Center before returning any product. Returned products must be properly packaged and shipped prepaid. Return shipping costs after repair will be paid by Seller except for overnight, express or special shipping costs which shall be paid by Purchaser. Conditions and Limitations TRANS-LUX MIDWEST CORPORATION d.b.a. Fair-Play Scoreboards FIVE YEAR LIMITED WARRANTY MONOCHROME LED MARQUEE and MESSAGE CENTERS This warranty covers equipment and software manufactured by the Seller only. It does not apply to installation or service labor. This warranty also does not apply to completed subassemblies (including, but not limited to, computers, keyboards, power supplies, monitors, disk drives, fans, air conditioning units, wireless components, etc.) or software manufactured by other companies. Where a third party s equipment or software is supplied hereunder, such manufacturer s warranty and warranty period shall apply in place of the above, and Seller hereby assigns to Purchaser all of its rights under transferable third party warranties for such equipment and/or software. Wireless control devices even if not defective may not function reliably in certain environments or otherwise due to outside causes beyond Seller s control, including but not limited to cell phones or portable computers. In the event it is determined a wireless device during the ninety (90) day period following shipment does not function in accordance with its specification without repeated errors or is otherwise consistently unreliable, and Seller determines repair or replacement thereof is not likely to improve performance, at Purchaser s request, upon return to Seller postage prepaid in like new condition within such time period, Seller s sole obligation shall be to refund the entire purchase price of such device, and thereafter Seller s sole obligation shall be to repair or replace defective components for the balance of the warranty period without responsibility or liability for claims for unreliable performance not due to defects. This warranty shall not apply in case of neglect, abuse or damage caused by user, sabotage, vandalism, acts of terrorists, improper storage, improper installation, maintenance or servicing of the equipment by anyone other than Seller or the Seller s authorized representative, or failure to operate and maintain according to Seller s instructions furnished with the product. The warranty also does not apply to components damaged by power surges, water damage, lightning, wind damage or other acts of nature, excessive application of power, or burn in due to static (non-moving) images applied for lengthy periods of time, replacement of fluorescent or incandescent lamps or light emitting diodes (LEDs), nor the use of high pressure washes, exposure to concentrated detergents or other chemical agents or solvents, improper handling by third party shippers, disabling fans or other factory installed cooling systems, installing non-factory replacement parts, removing warning labels and protection devices, software conflicts due to non-factory loading of additional software on the controller, computer viruses or loading software onto non-factory authorized computer. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OF SELLER, EXPRESS OR IMPLIED, AND, EXCEPT TO THE EXTENT HEREIN PROVIDED, SELLER DOES NOT MAKE ANY WARRANTY WHATSOEVER INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR USE OR PURPOSE. Seller s entire liability and Purchaser s exclusive remedy for damages from any cause whatsoever, and regardless of the form of action, whether in contract or in tort including negligence, shall be limited to actual damages up to the purchase price or $25,000.00 whichever is less. The foregoing limitation of liability will not apply to claims by Purchaser for bodily injury or damage to real property or tangible personal property for which Seller is legally liable. In no event shall Seller be liable for any special, punitive, or consequential damages or lost profits or data even if Seller has been advised of the possibility of such damages. Seller will not be liable for any claim by Purchaser based on any third party claim. No person is authorized to give any other warranty or to assume any additional obligation on the Seller s behalf unless such additional warranty or obligation is made in writing and signed by a duly authorized officer of Seller. Fair-Play ã Scoreboards - A Division of Trans-Lux Midwest Corporation For Service contact: Trans-Lux Repair Center, 110 Richards Avenue, Norwalk, CT 06854 Telephone: 800-462-2716 Fax: (203) 831-8827 Internet Address - www.fair-play.com Effective 05-18-04 2004, Fair-Play Scoreboards, All rights reserved.
TRANS-LUX MIDWEST CORPORATION d.b.a. Fair-Play Scoreboards FIVE YEAR LIMITED WARRANTY COLOR CAPTIVUE LED MARQUEE and MESSAGE CENTER Trans-Lux Midwest Corporation ( Seller ) manufactures a variety of solid state electronic products. Seller warrants that, for a period of five (5) years from date of invoice of any of its Color CaptiVue Light Emitting Diode (LED) products, it will repair or replace, from new or serviceable used parts, at the Seller s option, any of its LED electronic products that are found to be defective in materials and/or workmanship under normal use and maintenance. This warranty requires that the defective equipment be returned to Seller. A return authorization number must be obtained from the Seller s Service Center before returning any product. Returned products must be properly packaged and shipped prepaid. Return shipping costs after repair will be paid by Seller except for overnight, express or special shipping costs which shall be paid by Purchaser. Conditions and Limitations This warranty covers equipment and software manufactured by the Seller only. It does not apply to installation or service labor. This warranty also does not apply to certain subassemblies (including, but not limited to, computers, keyboards, monitors, disk drives, air conditioning units, wireless components, etc.) or software manufactured by other companies. Where a third party s equipment or software is supplied hereunder, such manufacturer s warranty and warranty period shall apply in place of the above, and Seller hereby assigns to Purchaser all of its rights under transferable third party warranties for such equipment and/or software. Wireless control devices even if not defective may not function reliably in certain environments or otherwise due to outside causes beyond Seller s control, including but not limited to cell phones or wireless networks. In the event it is determined a wireless device during the ninety (90) day period following shipment does not function in accordance with its specification without repeated errors or is otherwise consistently unreliable, and Seller determines repair or replacement thereof is not likely to improve performance, at Purchaser s request, upon return to Seller postage prepaid in like new condition within such time period, Seller s sole obligation shall be to refund the entire purchase price of such device, and thereafter Seller s sole obligation shall be to repair or replace defective components for the balance of the warranty period without responsibility or liability for claims for unreliable performance not due to defects. This warranty shall not apply in case of neglect, abuse or damage caused by user, sabotage, vandalism, acts of terrorists, improper storage, installation, maintenance or servicing of the equipment by anyone other than Seller or the Seller s authorized representative, or failure to operate and maintain according to Seller s instructions furnished with the product. The warranty also does not apply to components damaged by power surges, water damage, lightning, wind damage or other acts of nature, excessive application of power, burn in due to static (non-moving) images applied for lengthy periods of time, color shift and color variations due to the inherent deterioration of the red, green, and blue component, replacement of fluorescent or incandescent lamps or light emitting diodes (LEDs) nor the use of high pressure washes, exposure to concentrated detergents or other chemical agents or solvents, improper handling by third party shippers, disabling fans or other factory installed cooling systems, installing non-factory replacement parts, removing warning labels and protection devices, software conflicts due to non-factory loading of additional software on the controller, computer viruses or loading software onto non-factory authorized computer. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OF SELLER, EXPRESS OR IMPLIED, AND, EXCEPT TO THE EXTENT HEREIN PROVIDED, SELLER DOES NOT MAKE ANY WARRANTY WHATSOEVER INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR USE OR PURPOSE. Seller s entire liability and Purchaser s exclusive remedy for damages from any cause whatsoever, and regardless of the form of action, whether in contract or in tort including negligence, shall be limited to actual damages up to the purchase price or $25,000.00 whichever is less. The foregoing limitation of liability will not apply to claims by Purchaser for bodily injury or damage to real property or tangible personal property for which Seller is legally liable. In no event shall Seller be liable for any special, punitive, or consequential damages or lost profits or data even if Seller has been advised of the possibility of such damages. Seller will not be liable for any claim by Purchaser based on any third party claim. No person is authorized to give any other warranty or to assume any additional obligation on the Seller s behalf unless such additional warranty or obligation is made in writing and signed by a duly authorized officer of Seller. Trans-Lux Midwest Corporation For Service contact: Trans-Lux Help Desk 1700 Delaware Avenue Des Moines, Iowa 50317 Telephone: 800-462-2716 Fax: (515) 263-7105 Fair-Play Scoreboards - A Division of Trans-Lux Midwest Corporation For Service contact: Trans-Lux Repair Center, 110 Richards Avenue, Norwalk, CT 06854 Telephone: 800-462-2716 Fax: (203) 831-8827 Internet Address - www.fair-play.com Effective 12-6-06 2006, Trans-Lux Midwest, All rights reserved.